2. Anova
  3. D6000

Anova D6000 Assembly Instruction

  • Hello! I've reviewed the Assembly Instructions for the Landscape FUSION Rally D6000 Rectangular Table. This document outlines the necessary steps for assembling the table, including parts list, hardware details, required tools, and cleaning instructions. I'm ready to answer any questions you might have about assembling or maintaining this product.
  • What type of cleaning products should be used?
    Is it ok to use vinyl cleaners or protectants?
    Do I need special tools to assemble the table?
    How many people are needed for assembling the table?
ASI 221C HRD80
Assembly Instructions for D6000 Rally Rectangular Table
A
SSEMBLY
INSTRUCTIONS
Parts List Hardware Included Tools Needed
2 Seats 12 – 5/16 x 1 Bolt Ratchet with 1/2”and 9/16” Socket
1 Tabletop 12 – 5/16 Flange Nut 1/2”, 9/16”, and 5/8” Wrench
4 Supports 24 – 5/16 Washer Level
2 Crossbraces 2 – 3/8 x 7/8 Bolt
2 – 3/8 Flange Nut
18 – 3/8 Washer
4 – 3/8 x 4 3/4 Bolt
4 – 3/8 Acorn Nut
To prevent scratching on any of the finished pieces, we recommend assembling the unit on packing
material (paper and cardboard). Do not drag assembled unit on any surface. The assembly is a two-
person operation.
Cleaning Recommendations
For cleaning, use mild household cleansers or soap and water.
Do not use vinyl cleansers or protectants.
Sea
t
Tabletop
Support
Crossbrace
211 N. Lindbergh Blvd. • St. Louis, MO 63131-7809
800-231-1327 • www.landscapebrands.com
ASI 221C HRD80
A
SSEMBLY
INSTRUCTIONS
Note: Before assembling the nuts to the bolts, it is recommended that a light oil or petroleum jelly be
applied to the bolt threads.
1. Place tabletop upside down on a level protected surface.
2. Align support holes with tabletop holes, with supports on outside of table brackets.
3. With washers on both sides, insert 5/16”x 1” bolts through holes and attach 5/16” flange nuts
to bolts, leaving finger tight.
4. With crossbrace end between supports, align holes, closest to tabletop, in supports and
crossbrace. With washers on both sides, insert 3/8”x 4 3/4” bolt through both supports and
crossbrace, attach 3/8”acorn nut to bolt, leaving finger tight.
5. Align holes, furthest from tabletop, in supports, and install (3) 3/8” washers between supports.
With washers on both sides insert 3/8”x 4 3/4" bolt through both supports and (3) washers,
attach 3/8” acorn nut to bolt, leaving finger tight.
6. Align other end of crossbrace with hole in the tabletop. With washers on both sides insert
3/8”x 7/8” bolt through holes and attach flange nut, leaving finger tight.
7. Repeat steps 4, 5 and 6 for other side.
8. Align support and seat holes, with supports on outside of seat brackets. With washers on both
sides, insert 5/16”x 1” through holes and attach 5/16” flange nuts, leaving finger tight.
9. Turn table right side up.
10. Level all components.
11. Tighten hardware. Retighten hardware two weeks after initial assembly.
Diagram #1 Diagram #2
Flatwasher
Crossbrace
Acorn Nut Flatwasher
3/8 x 4 3/4 Bolt
Flatwashers (3)
Support
/