TBRA052_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
front runner
TBRA052
ENG
1
Thank you for purchasing a Front Runner Expander Chair Side Table.
Before you start, take a moment to familiarize yourself with the Fitting Instructions and the included components.
Refer to Page 2 for a list of all the components, quantities and tools required.
READ ME !
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
EXPANDER CHAIR SIDE TABLE
TBRA052_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
FIGURE 1.1
CHECK ONLINE FOR THE LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
7
8
1
4
5
9
2
6
3
IN THE BOX
1 1 X Side Table Top
2 1 X Table Hinge
3 1 X Strap
4 1 X M5x10 Button Head
5 1 X M5 Nylock Nut
6 2 X M5 x 16 Button Head
7 1 X Table Hook
8 2 X Long Hex Nut
9 1 X M5 Nut Cap
3mm
8mm
2
1
8
6
A
7
3
TBRA052_REV_A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
3
FIT AND SECURE 2
2.1
2.2
2.3
Slide the Table Hinge (Item 2) in between the
tube and the chair material as shown.
Asemble the Table Top (Item 1) to the Table
Hinge (Item 2) using M5 x 15 Button Head
screws and Long Hex Nuts (Item 8)
Feed the Strap (Item 3) through the Table
Hook (Item 7) as shown.
A) Feed the Strap in from the top of the
first slot.
B) Feed the Strap in from the bottom to
the second slot.
C) Feed the Strap in from the top at the 3
slot.
D) Feed the Strap in from the bottom of
the first slot.
3mm
8mm
C
B
D
TBRA052_REV _A00 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
4
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner Dealer in person or online.
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FINISH
3
Congratulations! You did it. Take a step back and admire your work!
3mm
8mm
2.4
Secure the Strap (Item 3) to the Table Top
(Item 1) using M5 x 10 Button Head screw
(Item 4) and Nyloc Nut (Item 5). Place the
Table Hook (Item 7) over the arm rest and
adjust the Strap (Item 3) until the Table Top
(Item 1) is level.
7
3
4
59
-
1
-
2
-
3
-
4
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Front Runner CHAI007 User guide
-
Front Runner TBRA036 Installation guide
-
Front Runner STRA069 Installation guide
-
Front Runner SSWO009 Installation guide
-
Front Runner STRA057 Installation guide
-
Front Runner KRFB004T Installation guide
-
Front Runner KSCC002T Installation guide
-
Front Runner RRAC285 Installation guide
-
Front Runner TENT031 User manual
-
Front Runner KSTL002T Installation guide
