ENG
RRAC281_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
1
Don’t be a hero and muscle through this installation without reading these fitting instructions first! Improper installation of this gear may void certain
aspects of your warranty.
Before you begin, take a moment and open all your Front Runner rack kit boxes and gather the assembly instructions for the various components.
A complete kit will contain:
1. A Front Runner Mounting System specific to your vehicle
2. A Front Runner Rack Tray or Load Bar Slats
This document will guide you through the assembly of the mounting system and assist you in fitting the roof rack tray or load bars to your specific
vehicle.
Please refer to the next page for a list of all the components, quantities and tools required.
RRAC281
READ ME FIRST
START HERE!
front runner TOYOTA LAND CRUISER 100 SERIES
Slimsport Rack Wind Fairing
IMPORTANT WARNING!
IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. IMPROPER ATTACHMENT COULD
RESULT IN AN AUTOMOBILE ACCIDENT, AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT
RUNNER PRODUCTS TO YOUR VEHICLE, CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND
DAMAGE. THEREFORE, YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO
INSTALLATION OR USE. IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY
FAMILIAR WITH THE INSTALLATION PROCEDURES, YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.
NOTE: Front Runner will not be responsible for any damage caused by the failure to install the product according to these instructions.
Please call us if you have any questions about the installation of this product.
RRAC281_REV_A01 © 2023 FRONT RUNNER VEHICLE OUTFITTERS
2
TOOLS NEEDED
CHECK ONLINE FOR LATEST FITMENT GUIDE WWW.FRONTRUNNEROUTFITTERS.COM
GET ORGANIZED
1
IN THE BOX
1 2 X Side Bracket 1 LH / 1 RH
2 1 X Wind Fairing
3 9 X M6 x 16 Flange Button Head Bolt
4 1 X Centre Bracket
5 2 X Light Bar Bracket 01 1 LH / 1 RH
6 2 X Light Bar Bracket 02 1 LH / 1 RH
7 3 X M8 x 16 Hex Bolt
8 3 X M8 Nyloc Nut
9 3 X M8 Nut Cap
10 1 X Rubber Seal
1
2
3
4
5
6
7
8
9
10
Cordless
Driver
13mm
Torx
T30
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
3
RRAC281_REV_A01
FIT AND SECURE
2
2.1
2.2
2.3
Start by undoing the bolts on the front of
the Roof rack holding the front slat in place
using a T30 Torx bit.
Remove the front slat.
Slide the M8 x 16 Hex Bolt (Item 7) into the
slat as shown.
Place the Wind Fairing Center Support
Bracket (Item 4) over the M8 x 16 Hex Bolt
(Item 7) with the M8 Nyloc Nut (Item 8).
Slide the Wind Fairing Center Support
Bracket to the center of the slat. DO NOT
TIGHTEN.
Refit the Slat to the Roof Rack and tighten
the side with T30 Torx.
Assemble the Wind Fairing Side Brackets
(Item 1) on the Left and Right side with the
M6 x 16 Button Head Flange Bolt (Item 3) as
shown. 5
8
7
4
3
1
Torx
T30
Cordless
Driver
Torx
T30
Cordless
Driver
13mm
Torx
T30
Cordless
Driver
Tightening Torque:
M6 : 8-10Nm / 5.9 ft lb - 7.38 ft lb
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
3
RRAC281_REV_A01
FIT AND SECURE
2
2.4
2.5
Assemble the Wind Fairing and Wind Fairing
Rubber Seal (Item 2 & 10). The bubble should
face down. Trim if required.
Fasten the above mentioned assembly to the
Support Brackets (Item 4 & 5) with the M6 x
16 Button Head Flange Bolts (Item 3) using a
T30 Torx as shown.
Fully tighten the M8 Nyloc Nut that was
inserted in 2.2.
6
If you would like to fit a Light Bar above the
rack using the standard fairing, position the
light bar brackets (Item 5 or 6) and secure
using a M8x20 hex bolt and a M8 Nyloc Nut
(Item 7 & 8)
Do the same on the opposite side.
Place M8 Nut Caps (Item 9) over all the nuts.
9
8
5
7
6
Torx
T30
Cordless
Driver
13mm
13mm
10
2
3
4
5
Tightening Torque:
M8 : 15-20Nm / 11.06 ft lb - 14.75 ft lb
© 2023 FRONT RUNNER VEHICLE OUTFITTERS
4
RRAC281_REV_A01
4
COMPLETION
3
3.1
Congratulations! You did it. Take a step back and admire your work!
INSTALL OTHER VEHICLE AND RACK ACCESSORIES
4
Now's the time to visit your favorite Front Runner dealer in person or online.
IMPORTANT!
Be sure to tag us. We love to see our gear in action! #FrontRunnerOutfitters #BornToRoam
Share your adventures on:
FRONT RUNNER RACK KITS OFTEN HAVE A HIGHER LOAD RATING THAN THE VEHICLES THEY ARE MOUNTED TO. PLEASE REFER TO YOUR SPECIFIC VEHICLE MANUFACTURER
FOR A RECOMMENDED ROOF RATING. FRONT RUNNER CANNOT BE RESPONSIBLE FOR IMPROPER LOADING BEYOND THE VEHICLE MANUFACTURER'S STATED LOAD CAPACITY.
/
