Table of contents
8
Fortima F 1250
Original operating instructions 150001157_04_us
16.7.3 Securing the storage compartment flap ...................................................................................183
16.7.4 Lifting the machine...................................................................................................................183
16.7.5 Lashing the machine................................................................................................................184
17 Settings...................................................................................................................................186
17.1 Setting the baling pressure ......................................................................................................186
17.2 Setting the number of twine layers...........................................................................................187
17.3 Setting the number of net layers ..............................................................................................187
17.4 Adjusting the twine limiter ........................................................................................................188
17.5 Setting the twine brake ............................................................................................................189
17.6 Releasing the twine brake........................................................................................................190
17.7 Setting the magnetic coupling of the twine tying......................................................................190
17.8 Setting "Position of twine guide slide" sensor .......................................................................... 191
17.9 Setting wrapping material brake ..............................................................................................192
17.10 Setting the brake force release when feeding wrapping material ............................................192
17.11 Checking brake force release in tying position ........................................................................193
17.12 Setting the spreading bracket of the tying mechanism ............................................................194
17.13 Adjusting the net wrapping cutting unit ....................................................................................194
18 Service & maintenance..........................................................................................................195
18.1 Observe the service record booklet .........................................................................................195
18.2 Maintenance table....................................................................................................................195
18.2.1 Maintenance – Before the season ...........................................................................................195
18.2.2 Maintenance – After the season ..............................................................................................196
18.2.3 Maintenance – once after 10 hours .........................................................................................197
18.2.4 Maintenance – once after 50 hours .........................................................................................197
18.2.5 Maintenance – every 10 hours, at least daily...........................................................................197
18.2.6 Maintenance – every 50 hours.................................................................................................198
18.2.7 Maintenance – Every 500 hours ..............................................................................................198
18.2.8 Maintenance – Every 2 years ..................................................................................................198
18.3 Lubrication chart ......................................................................................................................198
18.4 Lubricating the universal shaft .................................................................................................203
18.5 Tightening torques ...................................................................................................................204
18.6 Checking/maintaining tyres......................................................................................................207
18.7 Servicing the main gearbox .....................................................................................................209
18.8 Check hydraulic hoses.............................................................................................................209
18.9 Cleaning the machine ..............................................................................................................210
18.10 Clean the bushing and the drawbar eye ..................................................................................211
18.11 Cleaning drive chains...............................................................................................................211
18.12 Remove corrosion from the spreading bracket ........................................................................212
18.13 Protecting brake disc of the wrapping material brake from corrosion ......................................212
18.14 Adjusting the net wrapping cutting unit ....................................................................................213
18.15 Checking the screw connections on the drawbar ....................................................................213
18.16 Setting the scraper to the spiral roller ......................................................................................214
18.17 Adjusting the spring rail of the tying unit ..................................................................................214
18.18 Releasing the cam clutch on the universal shaft......................................................................215
18.19 Adjust drive chains...................................................................................................................215
18.19.1 Drive chain of the bale formation conveyor..............................................................................215
18.19.2 Drive chain of the pick-up ........................................................................................................216
18.19.3 Drive chain of the rollers ..........................................................................................................216
18.19.4 Drive chain of the auger conveyor ...........................................................................................217
18.20 Servicing chain lubrication unit ................................................................................................217
18.20.1 Checking oil level, topping up oil and changing filter ...............................................................218
18.20.2 Position of the oil brushes........................................................................................................219
18.20.3 Position of the dosing units ......................................................................................................220
18.20.4 Cleaning the dosing units.........................................................................................................221
18.20.5 Replacing the hose on the dosing unit.....................................................................................222
18.21 Servicing compressed air brake (for version with "Compressed air brake") ............................ 223
18.21.1 Cleaning air filter ......................................................................................................................223
18.21.2 Drain condensation water from the compressed air tank.........................................................224
19 Disturbance, cause and remedy...........................................................................................225