Gigabyte MZ32-AR1 User manual

Category
Motherboards
Type
User manual
MZ32-AR1
AMD EPYC™ 7003 Server Motherboard
User Manual
Rev. 3.0
Copyright
© 2021 GIGA-BYTE TECHNOLOGY CO., LTD. All rights reserved.
The trademarks mentioned in this manual are legally registered to their respective owners.
Disclaimer
Information in this manual is protected by copyright laws and is the property of GIGABYTE.
Changes to the specifications and features in this manual may be made by GIGABYTE
without prior notice. No part of this manual may be reproduced, copied, translated, transmitted, or
published in any form or by any means without GIGABYTE's prior written permission.
Documentation Classications
In order to assist in the use of this product, GIGABYTE provides the following types of documentation:
 UserManual:detailedinformation&stepsabouttheinstallation,congurationandusethis
product (e.g. motherboard, server barebones), covering hardware and BIOS.

User Guide: detailed information about the installation & use of an add-on hardware or
  softwarecomponent(e.g.BMCrmware,rail-kit)compatiblewiththisproduct.
Quick Installation Guide: a short guide with visual diagrams that you can reference easily for
installation purposes of this product (e.g. motherboard, server barebones).
Please see the support section of the online product page to check the current availability of these
documents
For More Information
Forrelatedproductspecications,thelatestrmwareandsoftware,andotherinformation,pleasevisit
our website at: http://www.gigabyte.com.
For GIGABYTE distributors and resellers, additional sales & marketing materials are available from our
reseller portal: http://reseller.b2b.gigabyte.com
For further technical assistance, please contact your GIGABYTE representative or visit
http://esupport.gigabyte.com/ to create a new support ticket.
For any general sales or marketing enquires, you may message GIGABYTE server directly by
email: server[email protected].
- 3 -
Table of Contents
MZ32-AR1 Motherboard Layout ......................................................................................5
Block Diagram .................................................................................................................7
Chapter 1 Hardware Installation .....................................................................................9
1-1 Installation Precautions .................................................................................... 9
1-2 ProductSpecications .................................................................................... 10
1-3 Installing and Removing the CPU and Heat Sink ........................................... 12
1-4 Installing and Removing Memory ................................................................... 13
1-4-1 8-ChannelMemoryConguration ..........................................................................13
1-4-2 Installing and Removing the Memory Module .......................................................14
1-4-3 Processor and Memory Module Matrix Table .........................................................14
1-4-4 Memory Population Table ......................................................................................15
1-5 Installing and Removing the M.2 SSD Module ............................................... 16
1-6 Installing and Removing the Mezzanine Card ................................................ 17
1-7 Back Panel Connectors .................................................................................. 18
1-8 Internal Connectors ........................................................................................ 19
1-9 Jumper Settings ............................................................................................. 27
Chapter 2 BIOS Setup ..................................................................................................28
2-1 The Main Menu .............................................................................................. 30
2-2 Advanced Menu ............................................................................................. 33
2-2-1 Trusted Computing .................................................................................................35
2-2-2 PSP Firmware Versions ..........................................................................................36
2-2-3 Legacy Video Select ...............................................................................................37
2-2-4 AST2500SuperIOConguration ...........................................................................38
2-2-5 S5 RTC Wake Settings ...........................................................................................41
2-2-6 Serial Port Console Redirection .............................................................................42
2-2-7 CPUConguration ..................................................................................................46
2-2-8 PCI Subsystem Settings .........................................................................................47
2-2-9 USBConguration ..................................................................................................49
2-2-10 NetworkStackConguration ..................................................................................51
2-2-11 NVMeConguration ...............................................................................................52
2-2-12 SATAConguration.................................................................................................53
2-2-13 UEFIPOSTLOGOConguration ...........................................................................54
2-2-14 AMDMemCongurationStatus .............................................................................55
2-2-15 T1sAuthConguration ...........................................................................................56
2-2-16 Intel(R) I350 Gigabit Network Connection ..............................................................57
2-2-17 VLANConguration ................................................................................................59
- 4 -
2-2-18 MACIPv4NetworkConguration ...........................................................................61
2-2-19 MACIPv6NetworkConguration ...........................................................................62
2-3 AMD CBS Menu ............................................................................................. 64
2-3-1 CPU Common Options ...........................................................................................65
2-3-2 DF Common Options ..............................................................................................71
2-3-3 UMC Common Options ..........................................................................................76
2-3-4 NBIO Common Options ..........................................................................................91
2-3-5 FCH Common Options ...........................................................................................97
2-3-6 NTB Common Options .........................................................................................101
2-3-7 SOC Miscellaneous Control .................................................................................102
2-3-8 Workload Tuning ...................................................................................................103
2-4 AMD PBS Menu ........................................................................................... 104
2-4-1 RAS ......................................................................................................................105
2-5 Chipset Setup Menu ..................................................................................... 107
2-5-1 North Bridge .........................................................................................................108
2-5-2 Fabric Resource ...................................................................................................109
2-6 Server Management Menu ........................................................................... 110
2-6-1 System Event Log ................................................................................................112
2-6-2 View FRU Information ..........................................................................................113
2-6-3 BMCNetworkConguration .................................................................................114
2-6-4 IPv6BMCNetworkConguration ......................................................................... 115
2-7 Security Menu .............................................................................................. 116
2-7-1 Secure Boot ......................................................................................................... 117
2-8 Boot Menu .................................................................................................... 119
2-9 Save & Exit Menu ......................................................................................... 121
2-10 BIOS POST Beep code (AMI standard) ....................................................... 122
2-10-1 PEI Beep Codes ...................................................................................................122
2-10-2 DXE Beep Codes .................................................................................................122
- 5 -
MZ32-AR1 Motherboard Layout
CPU
DIMM_P0_A1
DIMM_P0_A0
DIMM_P0_B0
DIMM_P0_B1
DIMM_P0_C0
DIMM_P0_C1
DIMM_P0_D0
DIMM_P0_D1
DIMM_P0_F0
DIMM_P0_F1
DIMM_P0_G0
DIMM_P0_G1
DIMM_P0_H0
DIMM_P0_H1
DIMM_P0_E0
DIMM_P0_E1
17
16
19
18
5
910
12
13
14
15
1 2 3 4
6
7
8
11
20
21
22
2324
25
26
27
30
29
28
31
32 33 34 35 36 37 38
39
40
41
42
43 44
- 6 -
Item Code Description
1 R_USB3 USB 3.0 Port
2 LAN1_2 GbE Ethernet LAN Port #1/ GbE Ethernet LAN Port #2
3 USB3_MLAN Server Management LAN Port (Top)/ USB3.0 Ports (Bottom)
4 SW_ID ID button with LED
5 MEZZ_1A/MEZZ_1B OCP Mezzanine Connector
6 COM1_VGA Serial Port (Top)/ VGA Port (Bottom)
7 SYS_FAN1 System Fan Connector #1
8 SYS_FAN2 System Fan Connector #2
9 BAT1 Battery Socket
10 ATX1 2 x 12 Pin Main Power Connector
11 CPU0_FAN CPU Fan Connector #0
12 P12V_AUX1 2 x 4 Pin Power Connector (for CPU)
13 P12V_AUX2 2 x 4 Pin Power Connector (for Memory)
14 SATA0 Slimline SAS 4i Connector (SATAIII 6Gb/s Signal)
15 SATA1 Slimline SAS 4i Connector (SATAIII 6Gb/s Signal)
16 U2_3 Slimline SAS 4i Connector (NVMe/PCIe Gen3 x4)
17 U2_1 Slimline SAS 4i Connector (NVMe/PCIe Gen3 x4)
18 U2_0 Slimline SAS 4i Connector (NVMe/PCIe Gen3 x4)
19 U2_2 Slimline SAS 4i Connector (NVMe/PCIe Gen3 x4)
20 F_USB3 Front Panel USB 3.0 Connector
21 FP_1 Front Panel Header
22 CASE_OPEN Case Open Intrusion Alert Header
23 BP_1 HDD Backplane Board Connector
24 M2_1 M.2 slot (PCIe Gen4 x4, Support NGFF-2242/2260/2280)
25 M2_2 M.2 slot (PCIe Gen4 x4, Support NGFF-2242/2260/2280)
26 F_USB2 USB 2.0 Header
27 SPI_TPM TPM Module Connector
28 SYS_FAN4 System Fan Connector #5
29 SYS_FAN4 System Fan Connector #4
30 SYS_FAN3 System Fan Connector #3
31 COM2 Serial Port Cable Connector
32 PCIE_1 PCIe x16 Slot (Gen3 x16/x8)
33 PCIE_2 PCIe x8 Slot (Gen3 x0/x8)
34 PCIE_3 PCIe x16 Slot (Gen4 x16)
35 PCIE_4 PCIe x16 Slot (Gen4 x16)
36 PCIE_5 PCIe x16 Slot (Gen4 x8)
37 PCIE_6 PCIe x16 Slot (Gen4 x16)
38 PCIE_7 PCIe x16 Slot (Gen4 x16) switch with 4 x Slim-SAS 4i from 4 x U.2
39 SLINK3 Slimline SAS 4i Connector
40 SLINK2 Slimline SAS 4i Connector
41 SLINK1 Slimline SAS 4i Connector
42 SLINK0 Slimline SAS 4i Connector
43 IPMB IPMB Connector
44 LED_BMC BMC Firmware Readiness LED
- 7 -
Block Diagram
- 8 -
This page intentionally left blank
- 9 - Hardware Installation
1-1 Installation Precautions
The motherboard contains numerous delicate electronic circuits and components which can
become damaged as a result of electrostatic discharge (ESD). Prior to installation, carefully read
the user's manual and follow these procedures:
Prior to installation, do not remove or break motherboard S/N (Serial Number) sticker or
warranty sticker provided by your dealer. These stickers are required for warranty validation.
Always remove the AC power by unplugging the power cord from the power outlet before
installing or removing the motherboard or other hardware components.
When connecting hardware components to the internal connectors on the motherboard,
make sure they are connected tightly and securely.
When handling the motherboard, avoid touching any metal leads or connectors.
It is best to wear an electrostatic discharge (ESD) wrist strap when handling electronic
components such as a motherboard, CPU or memory. If you do not have an ESD wrist
strap,keepyourhandsdryandrsttouchametalobjecttoeliminatestaticelectricity.
Prior to installing the motherboard, please have it on top of an antistatic pad or within an
electrostatic shielding container.
Before unplugging the power supply cable from the motherboard, make sure the power
supply has been turned off.
Before turning on the power, make sure the power supply voltage has been set according to
the local voltage standard.
Before using the product, please verify that all cables and power connectors of your
hardware components are connected.
To prevent damage to the motherboard, do not allow screws to come in contact with the
motherboard circuit or its components.
Make sure there are no leftover screws or metal components placed on the motherboard or
within the computer casing.
Do not place the computer system on an uneven surface
.
Do not place the computer system in a high-temperature environment.
Turning on the computer power during the installation process can lead to damage to
system components as well as physical harm to the user.
If you are uncertain about any installation steps or have a problem related to the use of the
product,pleaseconsultacertiedcomputertechnician.
Chapter 1 Hardware Installation
Hardware Installation - 10 -
1-2 Product Specications
CPU
AMD EPYC™ 7003 series processor family
Single processor, 7nm, Socket SP3
Up to 64-core, 128 threads per processor
cTDP up to 240W
Fully support 280W
NOTE: Please make sure Fan-sink supports over 280W CPU
Compatible with AMD EPYC™ 7002 series processor family
Chipset System on Chip
Socket
Socket
Security
Security
Security UEFI Secure Boot
Silicon root of trust
SNMP Support: V3
Hardware-Level
Root of Trust
Support
Supported
NOTE! The system will take extra time to boot as it goes through RoT
authentication.
Memory 16 x DIMM slots
DDR4 memory supported only
8-Channel memory architecture
RDIMM modules up to 128GB supported
LRDIMM modules up to 128GB supported
3DS RDIMM/LRDIMM modules up to 256GB supported
Memory speed: Up to 3200*/ 2933 MHz
Note:
* Follow BIOS setting and memory QVL list if running 3200 Mhz with 2DPC
Onboard
Graphics
Integrated in Aspeed® AST2500
2D Video Graphic Adapter with PCIe bus interface
1920x1200@60Hz 32bpp
LAN 2 x 1GbE LAN ports (1 x Intel® I350-AM2)
1 x 10/100/1000 management LAN
Expansion Slots Slot_7: 1 x PCIe x16 (Gen4 x16 bus) slot; shared with 4 x NVMe ports
Slot_6: 1 x PCIe x16 (Gen4 x16 bus) slot
Slot_5: 1 x PCIe x16 (Gen4 x8 bus) slot
Slot_4: 1 x PCIe x16 (Gen4 x16 bus) slot
Slot_3: 1 x PCIe x16 (Gen4 x16 bus) slot
Slot_2: 1 x PCIe x8 (Gen3 x0 or x8 bus) slot
Slot_1: 1 x PCIe x16 (Gen3 x16 or x8 bus) slot; shared with slot_2
1 x OCP mezzanine slot with PCIe Gen3 x16 bandwidth (Type1, P1, P2, P3, P4;
Type2 P5 with NCSI supported)
- 11 - Hardware Installation
Expansion Slots 2 x M.2 slots:
- M-key
- PCIe Gen4 x4
- Supports NGFF-2242/2260/2280 cards
4 x NVMe ports:
- SlimSAS 4i type
- PCIe Gen4 x4 per port
- Shared with Slot_7 PCIe Gen4 x16 slot
Storage Interface 2 x SlimSAS 4i for 8 x SATA ports
Internal I/O
Connectors
1 x 24-pin ATX main power connector
2 x 8-pin ATX 12V power connectors
10 x SlimSAS connectors
2 x M.2 slots
1 x CPU fan headers
5 x System fan headers
1 x USB 3.2 Gen 1 header
1 x USB 2.0 header
1 x COM_2 header
1 x TPM header
1 x Front panel header
1 x HDD back plane board header
1 x PMBus connector
1 x IPMB connector
1xClearCMOSjumper
1xBIOSrecoveryjumper
1 x Buzzer
Rear I/O
Connectors
3 x USB 3.2 Gen 1
1 x VGA
1 x COM_1
2 x RJ45
1 x MLAN
1 x ID button with LED
TPM 1 x TPM header with SPI interface
Optional TPM2.0 kit: CTM010
Board
Management
Aspeed® AST2500 management controller
GIGABYTE Management Console (AMI MegaRAC SP-X) web interface
Form Factor E-ATX
305W x 330D (mm)
GIGABYTEreserves the right to make any changes to the product specications and product-related
information without prior notice.
Hardware Installation - 12 -
1-3 Installing and Removing the CPU and Heat Sink
Follow these instructions to Install the CPU:
1. Loosen the three captive screws in sequential order (1g2g3) securing the CPU cover.
2. Flip open the CPU cover.
3. Remove the CPU cap with CPU from the CPU frame using the handle on the CPU cap.
4. Using the handle on the CPU cap insert the new CPU cap with CPU installed into the CPU frame.
Note: Ensure that the CPU is installed in the CPU cap in the correct orientation, with the gold triangle
on the CPU aligned to the top left corner of the CPU cap.
5. Flip the CPU frame with CPU installed into place in the CPU socket.
6. Flip the CPU cover into place over the CPU socket.
7. Tighten the CPU cover screws in sequential order (1 g 2 g 3) to secure the CPU cover in place.
Read the following guidelines before you begin to install the CPU:
Make sure that the motherboard supports the CPU.
Always turn off the computer and unplug the power cord from the power outlet before installing
the CPU to prevent hardware damage.
Unplug all cables from the power outlets.
Disconnect all telecommunication cables from their ports.
Placethesystemunitonaatandstablesurface.
Open the system according to the instructions.
WARNING!
Failure to properly turn off the server before you start installing components may cause serious
damage. Do not attempt the procedures described in the following sections unless you are a
qualiedservicetechnician.
3
3
1
1
2
2
1
External cap
2
3
CPU
4
5
7
1
1
3
3
2
2
6
Note:
Lock the CPU by using a T20-Lobe driver to tighten 3 captive nuts in sequence as 1-3.
The screw tightening torque: 16.1 ± 1.2 kgf-cm.
- 13 - Hardware Installation
1-4 Installing and Removing Memory
Read the following guidelines before you begin to install the memory:
Make sure that the motherboard supports the memory. It is recommended that memory of the
same capacity, brand, speed, and chips be used.
Always turn off the computer and unplug the power cord from the power outlet before installing
the memory to prevent hardware damage.
Memory modules have a foolproof design. A memory module can be installed in only one
direction. If you are unable to insert the memory, switch the direction.
1-4-1 8-Channel Memory Conguration
This motherboard provides 16 DDR4 memory slots and supports 8-Channel Technology. After the memory
isinstalled,theBIOSwillautomaticallydetectthespecicationsandcapacityofthememory.
CPU
CPU
DIMM_P0_A1
DIMM_P0_A0
DIMM_P0_B0
DIMM_P0_B1
DIMM_P0_C0
DIMM_P0_C1
DIMM_P0_D0
DIMM_P0_D1
DIMM_P0_F0
DIMM_P0_F1
DIMM_P0_G0
DIMM_P0_G1
DIMM_P0_H0
DIMM_P0_H1
DIMM_P0_E0
DIMM_P0_E1
Hardware Installation - 14 -
1-4-2 Installing and Removing the Memory Module
Before installing a memory module, make sure to turn off the computer and unplug the
power cord from the power outlet to prevent damage to the memory module.
Be sure to install DDR4 DIMMs on to this motherboard.
Follow these instructions to install a DIMM module:
1. Insert the DIMM memory module vertically into the DIMM slot and push it down.
2. Close the plastic clip at both edges of the DIMM slots to lock the DIMM module.
3. Reverse the installation steps when you want to remove the DIMM module.
1
2
2
1-4-3 Processor and Memory Module Matrix Table
Processor and Memory Module Matrix Table
1 DIMMs
CPU#
CPU0 C1
2 DIMMs
CPU0 C1 D1
4 DIMMs
CPU0 C1 D1 G1 H1
8 DIMMs
CPU0 A1 B1 C1 D1 E1 F1 G1 H1
16 DIMMs
CPU0 A1A0 B1B0 C1C0 D1D0 E1E0 F1F0 G1G0 H1H0
Channel A Channel B Channel C Channel D Channel E Channel F Channel G Channel H
- 15 - Hardware Installation
Note:
When only one DIMM is used, it must be populated in memory slot DIMM1.
EPYC Memory Speed based on DIMM Population (Two DIMM per Channel)
DIMM
Type
DIMM Population Max EPYC 7003
DDR Frequency (MHz)
DIMM 0 DIMM 1
RDIMM
-- 1R 3200
1R 1R 2933
-- 2R or 2DR 3200
1R 2R or 2DR 2933
2R or 2DR 2R or 2DR 2933
LRDIMM
-- 4DR 3200
4DR 4DR 2933
-- 2S2R (4 Ranks) 3200
-- 2S4R (8 Ranks) 3200
2S2R (4 Ranks) 2S2R (4 Ranks) 2933
2S4R (8 Ranks) 2S4R (8 Ranks) 2933
3DS
-- 2S2R (4 Ranks) 2933
2S2R (4 Ranks) 2S2R (4 Ranks) 2666
-- 2S4R (8 Ranks) 2933
2S4R (8 Ranks) 2S4R (8 Ranks) 2666
DIMM
Type
DIMM Population Max EPYC 7003
DDR Frequency (MHz)
DIMM 0
RDIMM
1R (1 Rank) 3200
2R or 2DR (2 Ranks) 3200
LRDIMM
4DR (4 Ranks) 3200
2S2R (4 Ranks) 3200
2S4R (8 Ranks) 3200
3DS
2S2R (4 Ranks) 3200
2S4R (8 Ranks) 3200
EPYC Memory Speed based on DIMM Population (One DIMM per Channel)
1-4-4 Memory Population Table
Hardware Installation - 16 -
1-5 Installing and Removing the M.2 SSD Module
Follow the steps below to install an optional M.2 SSD module on your motherboard.
Step1. Insert the M.2 SSD module into the slot.
Step2. Secure it with the screw, tightening as necessary to fasten the M.2 SSD module in place.
1
2
- 17 - Hardware Installation
1-6 Installing and Removing the Mezzanine Card
Follow the steps below to install a mezzanine card on your motherboard.
Step1. Insert the mezzanine card into the system ensuring that the connector on the mezzanine card
connects to the connector on the motherboard.
Step2. Secure the mezzanine card to the system with three screws.
1
1
2
Hardware Installation - 18 -
1-7 Back Panel Connectors
uSerial Port
Connects to serial-based mouse or data processing devices.
vVGA Port
Connects to a monitor device.
wID button with LED
Whenthesystemidenticationisactive,theIDLEDonthefront/backpanelglowsblue.
x10/100/1000 Server Management LAN Port
The LAN port provides Internet connection with data transfer speeds of 10/100/1000Mbps. This port is
the dedicated LAN port for Server Management.
yUSB 3.0 Ports
The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveetc.
zRJ-45 LAN Port #1
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. See the section
below for a description of the states of the LAN port LEDs.
{RJ-45 LAN Port #2
The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate. See the section
below for a description of the states of the LAN port LEDs.
|USB 3.0 Port
The USB port supports the USB 3.0 specification. Use this port for USB devices such as a USB
keyboard/mouse,USBprinter,USBashdriveetc.
v
w
x
y
z
{
u
|
10/100/1000 LAN and ID Button LEDs
Link/Activity LED
Speed LED
LAN Port
ID Button/ LED:10/100/1000 LAN Speed LED:
State Description
Yellow On 1 Gbps data rate
Green On 100 Mbps data rate
Off 10 Mbps data rate
State Description
Blue On Systemidenticationisactive.
Off Systemidenticationisdisabled.
Whenremovingthecableconnectedtoabackpanelconnector,rstremovethecablefromyour
device and then remove it from the motherboard.
When removing the cable, pull it straight out from the connector. Do not rock it side to side to
prevent an electrical short inside the cable connector.
- 19 - Hardware Installation
1-8 Internal Connectors
Read the following guidelines before connecting external devices:
First make sure your devices are compliant with the connectors you wish to connect.
Before installing the devices, be sure to turn off the devices and your computer. Unplug the power
cord from the power outlet to prevent damage to the devices.
After installing the device and before turning on the computer, make sure the device cable has
been securely attached to the connector on the motherboard.
1) ATX 11) F_USB2
2) ATX_12V (for CPU) 12) COM2
3) ATX_12V (for Memory) 13) FP_1
4) CPU0_FAN 14) BP_1
5) SYS_FAN1 15) SPI_TPM
6) SYS_FAN2 16) IPMB
7) SYS_FAN3 17) LED_BMC
8) SYS_FAN4 18) BAT
9) SYS_FAN5 19) CASE_OPEN
10) F_USB3
CPU
CPU
DIMM_P0_A1
DIMM_P0_A0
DIMM_P0_B0
DIMM_P0_B1
DIMM_P0_C0
DIMM_P0_C1
DIMM_P0_D0
DIMM_P0_D1
DIMM_P0_F0
DIMM_P0_F1
DIMM_P0_G0
DIMM_P0_G1
DIMM_P0_H0
DIMM_P0_H1
DIMM_P0_E0
DIMM_P0_E1
1
2
3
4
6
5
18
9
12
13
7
8
11
10
14
15
16
17
19
Hardware Installation - 20 -
1/2/3) ATX/ATX_12V (2x12 Main Power Connector and 2x4 12V Power Connector)
With the use of the power connector, the power supply can supply enough stable power to all the components
onthemotherboard.Beforeconnectingthepowerconnector,rstmakesurethepowersupplyisturnedoff
and all devices are properly installed. The power connector possesses a foolproof design. Connect the power
supply cable to the power connector in the correct orientation. The 12V power connector mainly supplies
power to the CPU. If the 12V power connector is not connected, the computer will not start.
To meet expansion requirements, it is recommended that a power supply that can withstand high
power consumption be used (500W or greater). If a power supply is used that does not provide the
required power, the result can lead to an unstable or unbootable system.
PinNo. Denition
13 3.3V
14 -12V
15 GND
16 PS_ON
17 GND
18 GND
19 GND
20 -5V
21 +5V
22 +5V
23 +5V
24 GND
PinNo. Denition
1 3.3V
2 3.3V
3 GND
4 +5V
5 GND
6 +5V
7 GND
8 Power Good
9 5VSB
10 +12V
11 +12V
12 3.3V
5
8
1
4
PinNo. Denition
1 GND
2 GND
3 GND
4 GND
5 +12V
6 +12V
7 +12V
8 +12V
CPU
ATX
ATX_12V
ATX
113
12 24
ATX_12V
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122

Gigabyte MZ32-AR1 User manual

Category
Motherboards
Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI