Dahua ARK10C Quick start guide

Alarm Programming Keyboard Quick Start

Guide

V1.0.1

I

Table of Contents

1 Overview...................................................................................................... 1

2 Installation and Wiring.................................................................................. 2

2.1 Port and Wiring ............................................................................................... 2

2.2 Installation ...................................................................................................... 3

2.2.1 Direct Installation ..................................................................................... 3

2.2.2 86 Box Installation ................................................................................... 4

2.2.3 Leaving Wall Protection Installation ......................................................... 5

3 Operation (for ARC2008C-(G), ARC2016C-(G)) .......................................... 6

3.1 Select Model and 485 Address ....................................................................... 6

3.2 Front Panel ..................................................................................................... 7

4 Operation (for BUS and video alarm controllers) .......................................... 9

4.1 Select Model and 485 Address ....................................................................... 9

4.2 Front Panel ................................................................................................... 10

Appendix 1 Keyboard Programming Command ....................................................... 13

Appendix 1.1 Programming Command for ARC2008C-(G), ARC2016C-(G) ........... 13

Appendix 1.2 Programming Command for ARC9016C and ARC5X08C .................. 18

II

Important Safeguards and Warnings

Please read the following safeguards and warnings carefully before using the product in

order to avoid damages and losses.

Note:

 Do not expose the device to lampblack, steam or dust. Otherwise it may cause

fire or electric shock.

 Do not install the device at position exposed to sunlight or in high temperature.

Temperature rise in device may cause fire.

 Do not expose the device to humid environment. Otherwise it may cause fire.

 The device must be installed on solid and flat surface in order to guarantee

safety under load and earthquake. Otherwise, it may cause device to fall off or

turnover.

 Do not place the device on carpet or quilt.

 Do not block air vent of the device or ventilation around the device. Otherwise,

temperature in device will rise and may cause fire.

 Do not place any object on the device.

 Do not disassemble the device without professional instruction.

Warning:

 Please use battery properly to avoid fire, explosion and other dangers.

 Please replace used battery with battery of the same type.

 Do not use power line other than the one specified. Please use it properly.

Otherwise, it may cause fire or electric shock.

Special Announcement

 This manual is for reference only.

 All the designs and software here are subject to change without prior written

notice.

 All trademarks and registered trademarks are the properties of their respective

owners.

 If there is any uncertainty or controversy, please refer to the final explanation of

us.



1

1 Overview

This product is a universal programming keypad alarm, suitable for ARC2008C-(G),

ARC2016C-(G), ARC9016C-(G), ARC5408C-(C), ARC5808C-(C) and other models. It

supports parameter config of alarm controller, arm/disarm and operation status search.

2

2 Installation and Wiring

2.1 Port and Wiring

Use a screwdriver to remote take down rear cover of device by against the two holes at

top of device. See Figure 2-1.

Figure 2-1

Insert cable into cable port at back, see Figure 2-2.

3

Figure 2-2

2.2 Installation

2.2.1 Direct Installation

Step 1. See Figure 2-3 and dig hole on wall.

4

Figure 2-3

Step 2. Pull cable through the exit hole to external.

Step 3. Hang the device on screw. See Figure 2-4.

Figure 2-4

Step 4. Sort cables, and put back rear cover of the device.

2.2.2 86 Box Installation

This is installation via 86 box.

Step 1. Pull out cable through exit hole (Figure 2-3) and via pull slot to external.

Step 2. Fix rear cover on 86 box with screw, see Figure 2-5.

Step 3. Sort cable, put back rear cover.

5

Figure 2-5

2.2.3 Leaving Wall Protection Installation

If you want to achieve leaving wall protection function, please fix vandal-proof module of

rear cover on the wall with screw, see Figure 2-6.

Figure 2-6

6

3 Operation (for ARC2008C-(G), ARC2016C-(G))

Warning:

Content of this chapter is keyboard operation of ARC2008C-(G), ARC2016C-(G).

3.1 Select Model and 485 Address

Warning:

The device supports hot swap function. When the controller operates as normal,

connect keyboard wiring end to port at keyboard bottom, the COM indicator flashes

saying the function is normal.

Note:

When you first connect to controller, you need to select language and controller model,

you can use it once being successfully registered to controller.

Step 1. Connects one end of wire to alarm keyboard port.

Step 2. Press key, meantime insert the pair of one end of wire into keyboard

port and power port. Keyboard interface is ON and shoes language option.

Step 3. By pressing or key, select appropriate language, press

button.

Step 4. By pressing or , select “6-485 Addr”, press key.

Enter keyboard address, and press key.

It returns to model selection and address setup page.

Note:

 485 range is 01-08.

 485 address cannot be repeated when connecting to more than one

keyboards.

Step 5. By pressing or key, select corresponding product model, click

button. The keyboard generates a sound, shows homepage and COM

indicator flashes, means auto registration is successful. Keyboard and alarm

controller can have communication.

Note:

If you select wrong model, then registration will fail and COM indicator will NO.

7

3.2 Front Panel

Figure 3-1

Button or

Icon

Name

Note

COM indicator

Green NO：keyboard successfully registered to



alarm controller

Red NO：keyboard not registered to alarm controller



Arm/Disarm

Indicator

Green NO：Arming



Red NO：Disarming



Menu

Enter main menu page



Return to previous menu



Shortly press this button, to clear previously input



code

Page up

In menu, press this key to page up.



Long press this button, to search bypass status of



each channel

Page down

In menu, press this key to page down.



Long press this key, show zone 1-10 alarm info.



8

Button or

Icon

Name

Note

00*123456790 means zone 1-10 in group 00. To

search zone 11-20 alarm info, enter 01 here and so

forth.

0～9

Number key

Enter number （0～9）



*

Symbol（*）



Long press this button，input administrator/operator



password, or in homepage, input administration

/operator password to quickly disarm or arm.

#

Symbol（#）



Press this button, input administrator/operator



password to cancel alarm

Fire

long press this button for 3s，buzzer starts to alarm.

Device send fire alarm message to controller.

Robber

Long press this button key for 3s, buzzer will alarm.

Device will send alarm message to the alarm controller.

Medical Key

Long press this button for 3s，buzzer will alarm, and

device send medial message to controller.

Mute SOS

Long press this button for 3s，device will send mute SOS

message to controller.

Enter

Confirm setup.



Table 3-1

00*1 2 3 4 5 6 7 8 9 0

Figure 3-2

Note:

When check box is blank, zone is normal. When check box is black, zone is in alarm

status. When check box is black and blank, zone is ON (detector triggered).

9

4 Operation (for BUS and video alarm controllers)

Warning:

Content of this chapter is keyboard operation of BUS alarm controller (ARC9016C)

and video alarm controller (ARC5408C, ARC5808C).

4.1 Select Model and 485 Address

Warning:

The device supports hot swap function. When the controller operates as normal,

connect keyboard wiring end to port at keyboard bottom, the COM indicator flashes

saying the function is normal.

Note:

When you first connect to controller, you need to select language and controller model,

you can use it once being successfully registered to controller.

Step 1. Separately connect two ends of wire to keyboard port and power port on alarm

controller.

Step 2. Press key, meantime insert one end of wire into keyboard port.

Keyboard interface is ON and shoes language option.

Step 3. By pressing or key, select appropriate language, press

button. Enter alarm controller model selection page.

Step 4. By pressing or , select “6-485 Addr”, press key.

Enter keyboard address, and press key.

It returns to model selection and address setup page.

Note:

 485 address is shown in decimal system, range is 00-15.

 485 address cannot be repeated when connecting to more than one

keyboards.

Step 5. By pressing or key, select corresponding product model,

click button. The keyboard generate a sound, shows homepage and COM

indicator flashes, means auto registration is successful. Keyboard and alarm

controller can have communication.

10

Note:

If you select wrong model, then registration will fail and COM red indicator will NO.

4.2 Front Panel

Figure 4-1

Button or

Icon

Name

Note

COM indicator

Green NO：keyboard successfully registered to



alarm controller

Red NO：keyboard not registered to alarm controller



Arm/Disarm

Indicator

Green NO：Arming



Red NO：Disarming



Failure

Show this icon, means device has failure. In global



mode, you can long press for 3s，to

search device failure status.

Alarm

Show this icon, means device has alarm. In global



mode, long press for 3s，to search current

alarm condition.

Partial Arm

Show this icon, means device has partial arming. In



11

Button or

Icon

Name

Note

global mode, you can long press for 3s，to

search currently armed subsystem no.

Menu

Enter main menu page



Return to previous menu



Shortly press this button, to clear previously input



code

In global mode, long press this key for 3s, to show



each module status and means this module has

failure. When check box is blank, this module is

normal. See Figure 4-2.

Page up

In menu, press this key to page up.



In global mode, long press this button for 3s, to



show bypass status of each channel. Check box

next to zone is black, so zone has alarm or is

isolated.

Page down

In menu, press this key to page down.



In global mode, long press this button for 3s, to



show all alarm zones. Check box next to zone is

black, so zone has alarm.

0～9

Number key

Enter number （0～9）



In any mode, 1+ to search current mode.



*

Symbol（*）



In global mode, long press this button for 3s，to



search currently armed subsystem no., show all

subsystem arm/disarm status. Check box next to

zone is black, so the subsystem is armed.

#

Symbol（#）



Fire

Long press this button for 3s，buzzer starts to alarm.

Device send fire alarm message to controller.

Note:

Valid in any mode.

Robber

Long press this button key for 3s, buzzer will alarm.

Device will send alarm message to the alarm controller.

Note:

Valid in any mode.

Medical Key

Long press this button for 3s，buzzer will alarm, and

device send medial message to controller.

Note:

12

Button or

Icon

Name

Note

Valid in any mode.

Mute SOS

Long press this button for 3s，device will send mute SOS

message to controller.

Note:

Valid in any mode.

Enter

Confirm setup.



In global mode, long press this button for 3s，it



shows abnormal status of all zones. Check box next

to zone is black, so the zone is abnormal.

Table 4-1

Figure 4-2

13

Appendix 1 Keyboard Programming Command

Appendix 1.1 Programming Command for ARC2008C-(G),

ARC2016C-(G)

Command

Menu Path

Programming Operation

Definition

Arm

1.Arm/Disarm >

1-1.Arm

1+ OK+ 123456

Administrator

global arm

Disarm

1.Arm/Disarm >

1-2.Disarm

123456

Administrator

global disarm

Bypass

isolated

1.Arm/Disarm >

1-3.Bypass

isolated

1001 + OK+ 123456

Administrator

bypass zone 1

2001 + OK+ 123456

Administrator

cancel zone 1

bypass status

3001 + OK+ 123456

Administrator

isolated zone 1

4001 + OK+ 123456

Administrator

cancel zone 1

isolated status

Cancel alarm

1.Arm/Disarm >

1-4. Cancel

alarm

000 +OK+123456

administrator

cancel zone

alarm

001 +OK+123456

administrator

cancel zone 1

alarm

002 +OK+123456

administrator

cancel zone 2

alarm

……

Type

2. zone >

2-1.Type

00100+OK+909090

Installer set zone

1 to instant zone

00104005005+OK+909090

Installer set zone

1 to delay zone ，

entry delay is 5s，

exit delay is 5s

00108+OK+909090

Installer set zone

1 to all day zone

14

Command

Menu Path

Programming Operation

Definition

Link

2. zone >

2-2.Link

0010101+OK+909090

Installer set

zone 1 alarm link

siren output and

enable link

0010001+OK+909090

Installer set

zone 1 alarm link

siren out but

disable link

0011101+OK+909090

Installer set

zone 1 alarm link

alarm output

device and

enable link

0011001+OK+909090

Installer set

zone 1 alarm link

alarm output

device but disable

link

0012101+OK+909090

Installer set

zone 1 alarm link

buzzer and

enable link

0012001+OK+909090

Installer set

zone 1 alarm link

buzzer only and

disable link

Subsystem

2. zone > 2-3.

Subsystem

211001+OK+909090

In subsystem 1,

installer add

zone 1

210001+OK+909090

In subsystem 1,

installer delete

zone 1

111+OK+123456

Administrator arm

subsystem 1

110+OK+123456

Administrator

disarm

subsystem 1

Mode

3.Access

control >

3-1.Mode

0011+OK+909090

Installer set

access control 1

as anti-pinch

0012+OK+909090

Installer set

access control 1

as protection

15

Command

Menu Path

Programming Operation

Definition

0012+OK+909090

Installer set

access control c1

as other

Control

3.Access

control >

3-2.Control

0011+OK+909090

Installer enable

access control c1

0010+OK+909090

Installer disable

access control c1

Reset

4.Other >

4-1.Reset

909090

Installer reset

alarm controller

Initialize

4.Other >

4-2.Initialize

909090

Installer initialize

alarm controller

Tone

4.Other >

4-3.Tone

1

Enable keyboard

tone

0

Disable keyboard

tone

Time

4.Other >

4-4.Time

220150101+OK+909090

Installer set

system date is

2015/1/1

1102222+OK+909090

Installer set

system time as

10:22:22:

User

4.Other >

4-5.User

110888888+OK+123456

Administrator add

operator 10 ，or

change operator

10’s password

888888

210+OK+123456

Administrator

delete installer 10

Reboot

4.Other >

4-6.Reboot

909090

Installer reboot

alarm controller

Test mode

4.Other >

4-7.Test mode

1+OK+123456

Administrator

enable test mode

0+OK+123456

Administrator

disable test mode

Network

5.Communication

> 5-1.Network

1192#168#006#009#+OK+909

090

Installer set ip

address as

192.168.6.9

2255#255#255#000#+OK+909

090

Installer set

subnet mask as

255.255.255.0

3192#168#000#001#+OK+909

090

Installer set

gateway as

192.168.0.1

16

Command

Menu Path

Programming Operation

Definition

4377777#+OK+909090

Installer set port

as 377777

Call

5.Communication

> 5-2.Call

10571888888886666+OK+909

090

Installer set 1st

call group number

is

05718888888866

66

20571888888666666+OK+909

090

Installer set 2nd

call group number

is

05718888886666

66

31+OK+909090

Installer enable

call alarm function

30+OK+909090

Installer disable

call alarm function

Sms

5.Communication

> 5-3.SMS

18613576951066+OK+909090

Installer set 1st

call group number

is 13576951066

28613576951066+OK+909090

Installer set 2nd

call group number

is 13576951066

38613576951066+OK+909090

Installer set 3rd

call group number

is 13576951066

48613576951066+OK+909090

Installer set 4th

call group number

is13576951066

58613576951066+OK+909090

Installer set 5th

call group number

is13576951066

2g

5.Communication

> 5-5.2G

11+OK+909090

Installer enable

2g

10+OK+909090

Installer disable

2g

Wireless

5.Communication

> 5-6.Wireless

909090+any key on remote

control

Installer match

code of wireless

Siren

6.Output >

6-1.Siren

1+OK+909090

Installer enable

siren output

0+OK+909090

Installer disable

siren output

17

Command

Menu Path

Programming Operation

Definition

Alarm output

6.Output > 6-2.

Alarm output

20001+OK+909090

Installer set

zone 1 mode as

auto mode

21001+OK+909090

Installer set

zone 1 mode as

duress mode

22001+OK+909090

Installer set

zone 1 mode as

off mode

11001+OK+909090

Installer enable

alarm output 1

alarm output

enable

10001+OK+909090

Installer disable

alarm output 1

alarm output

enable

Zone

7. status > 7-1.

zone

001

Search zone 1

type

002

Search zone 2

type

003

Search zone 3

type

……

Access

control

7. status >

7-2.Access

control

1

Search access

control group

number

2001

Search access

control c1 work

mode

Version

7. status >

7-3.version

OK

Search alarm

programming

keyboard and

alarm controller

current version

Time

7. status >

7-4.Time

OK

Search alarm

controller current

system time

Communicati

on

7. status >

7-5.Communicati

on

2+OK+123456

Search rs485

address

11+OK+123456

Search ip address

12+OK+123456

Search subnet

mask

Page is loading ...

Dahua ARK10C Quick start guide

Dahua ARK10C Quick start guide

Related papers

Other documents