ML Accessories OS001B User manual

Brand: ML Accessories

Model: OS001B

Type: User manual

This manual is also suitable for

OS001

ML Accessories OS001B is a sensor that can be used with lights to detect motion and turn them on or off automatically. Here is some information that can help you to get the most out of your new sensor:

The OS001B has a built-in photosensor that allows you to set the light level at which the sensor will turn on.
Adjustable timer lets you set the amount of time that the lights will stay on after motion is detected.
The sensor has a detection range of up to 6 meters and a 120-degree detection angle.
The sensor can be mounted on a wall or ceiling, and it can be used indoors or outdoors.

The OS001B has a built-in photosensor that allows you to set the light level at which the sensor will turn on.
Adjustable timer lets you set the amount of time that the lights will stay on after motion is detected.
The sensor has a detection range of up to 6 meters and a 120-degree detection angle.
The sensor can be mounted on a wall or ceiling, and it can be used indoors or outdoors.

INSTALLATION & MAINTENANCE MANUAL

OS001 series

230V

50Hz

These instructions should be read carefully and retained after installation by the end user for

future reference and maintenance.

These instructions should be used to aid installation of the following products:

OS001 / OS001B

GENERAL INSTRUCTIONS

SAFETY

INSTALLATION

• Installation of this product should only be carried out by a qualiﬁed electrician or competent

person to the latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this product and load is ﬁtted) does not

exceed the rating of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for

installation

• This unit is rated at IP55

• This product is Class II double insulated

• This product can be connected to slave units – product code OS003

Note: Avoid mounting this product in direct sunlight and close to luminaires as this will cause

sensing issues

• Provide power to the required point of installation

Horizontal and vertical surface mounting:

• Using a slotted screwdriver, push on the base release tabs and pull the sensor away from the

base (see Fig 1)

Fig 1

OS001 series

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

OS001 / OS001B

SAFETY

• Installation of this product should only be carried out by a qualified electrician or competent person to the

latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this product and load is fitted) does not exceed the rating

of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• This unit is rated at IP55

• This product is Class I and requires an earth

INSTALLATION

Note: Avoid mounting this product: on non-stable surfaces; pointing directly at sunlight or bright surfaces or

near lamps or air vents

• Provide power to the required point of installation

HORIZONTAL AND VERTICAL SURFACE MOUNTING

• Using a slotted screwdriver, push on the base release tabs and pull the sensor away from the base (see Fig 1)

Fig 1

• Using the base as a template, secure the base to the desired surface using the fixings supplied ensuring not to

infringe with any gas/water pipes or electrical cables (see Fig 2)

Fig 2

• Ensuring correct polarity is observed, carefully wire as shown in Fig 3

• Note: earth point is for continuity only and is non functional

• Push the sensor head back onto the base until secured into position (see Fig 4)

• Switch on power supply and check for correct operation

Fig 2

OS001 series

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

OS001 / OS001B

SAFETY

• Installation of this product should only be carried out by a qualified electrician or competent person to the

latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this product and load is fitted) does not exceed the rating

of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• This unit is rated at IP55

• This product is Class I and requires an earth

INSTALLATION

Note: Avoid mounting this product: on non-stable surfaces; pointing directly at sunlight or bright surfaces or

near lamps or air vents

• Provide power to the required point of installation

HORIZONTAL AND VERTICAL SURFACE MOUNTING

• Using a slotted screwdriver, push on the base release tabs and pull the sensor away from the base (see Fig 1)

Fig 1

• Using the base as a template, secure the base to the desired surface using the fixings supplied ensuring not to

infringe with any gas/water pipes or electrical cables (see Fig 2)

Fig 2

• Ensuring correct polarity is observed, carefully wire as shown in Fig 3

• Using the base as a template, secure the base to the desired surface using the ﬁxings supplied

ensuring not to infringe with any gas/water pipes or electrical cables (see Fig 2)

OS001 series

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

OS001 / OS001B

SAFETY

• Installation of this product should only be carried out by a qualified electrician or competent person to the

latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this product and load is fitted) does not exceed the rating

of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• This unit is rated at IP55

• This product is Class I and requires an earth

INSTALLATION

Note: Avoid mounting this product: on non-stable surfaces; pointing directly at sunlight or bright surfaces or

near lamps or air vents

• Provide power to the required point of installation

HORIZONTAL AND VERTICAL SURFACE MOUNTING

• Using a slotted screwdriver, push on the base release tabs and pull the sensor away from the base (see Fig 1)

Fig 1

• Using the base as a template, secure the base to the desired surface using the fixings supplied ensuring not to

infringe with any gas/water pipes or electrical cables (see Fig 2)

Fig 2

• Ensuring correct polarity is observed, carefully wire as shown in Fig 3

OS001 series

These instructions should be read carefully and retained after installation by the end user for future reference and

maintenance.

These instructions should be used to aid installation of the following products:

OS001 / OS001B

SAFETY

• Installation of this product should only be carried out by a qualified electrician or competent person to the

latest Building and current IEE Wiring Regulations (BS7671)

• Please isolate mains prior to installation/maintenance

• Check the total load on the circuit (including when this product and load is fitted) does not exceed the rating

of the circuit cable, fuse or circuit breaker

• Please note the IP (Ingress of Protection) rating of this product when deciding the location for installation

• This unit is rated at IP55

• This product is Class I and requires an earth

INSTALLATION

Note: Avoid mounting this product: on non-stable surfaces; pointing directly at sunlight or bright surfaces or

near lamps or air vents

• Provide power to the required point of installation

HORIZONTAL AND VERTICAL SURFACE MOUNTING

• Using a slotted screwdriver, push on the base release tabs and pull the sensor away from the base (see Fig 1)

Fig 1

• Using the base as a template, secure the base to the desired surface using the fixings supplied ensuring not to

infringe with any gas/water pipes or electrical cables (see Fig 2)

Fig 2

• Ensuring correct polarity is observed, carefully wire as shown in Fig 3

Fig 3

• Push the sensor head back onto the base until secured into position (see Fig 4)

Fig 4

• Switch on power supply and check for correct operation

INTERNAL OR EXTERNAL CORNER MOUNTING

• This sensor can be corner-mounted by removing part of the base as shown (breakable areas) Screw the base

onto a suitable surface and insert the installation cables through the entry holes/grommets in the back of the

base and carefully wire as shown in Fig 3, ensuring the IP rating of the unit is maintained (silicone sealant may

need to be applied between the sensor and mounting surface) secure the sensor head onto the base (see Fig 5)

Fig 5

CEILING MOUNTING

• For ceiling mounting follow instructions for horizontal/vertical mounting and angle head accordingly (see Fig 2)

BLANKING INSERTS

• Blanking inserts are supplied that can be cut and attached to the lens to blank out areas of interference as

required i.e. heat sources, public pathways etc.

Fig 3

Fig 4

Internal or external corner mounting:

Note: sensor can be corner-mounted by removing part of the base as shown (breakable areas)

• Screw the base onto a suitable surface and insert the installation cables through the entry holes/

grommets in the back of the base and carefully wire as shown in Fig 3, ensuring the IP rating of

the unit is maintained (silicone sealant may need to be applied between the sensor and mounting

surface)

• Secure the sensor head onto the base (see Fig 5)

Fig 3

• Push the sensor head back onto the base until secured into position (see Fig 4)

Fig 4

• Switch on power supply and check for correct operation

INTERNAL OR EXTERNAL CORNER MOUNTING

• This sensor can be corner-mounted by removing part of the base as shown (breakable areas) Screw the base

onto a suitable surface and insert the installation cables through the entry holes/grommets in the back of the

base and carefully wire as shown in Fig 3, ensuring the IP rating of the unit is maintained (silicone sealant may

need to be applied between the sensor and mounting surface) secure the sensor head onto the base (see Fig 5)

Fig 5

CEILING MOUNTING

• For ceiling mounting follow instructions for horizontal/vertical mounting and angle head accordingly (see Fig 2)

BLANKING INSERTS

• Blanking inserts are supplied that can be cut and attached to the lens to blank out areas of interference as

required i.e. heat sources, public pathways etc.

Fig 3

• Push the sensor head back onto the base until secured into position (see Fig 4)

Fig 4

• Switch on power supply and check for correct operation

INTERNAL OR EXTERNAL CORNER MOUNTING

• This sensor can be corner-mounted by removing part of the base as shown (breakable areas) Screw the base

onto a suitable surface and insert the installation cables through the entry holes/grommets in the back of the

base and carefully wire as shown in Fig 3, ensuring the IP rating of the unit is maintained (silicone sealant may

need to be applied between the sensor and mounting surface) secure the sensor head onto the base (see Fig 5)

Fig 5

CEILING MOUNTING

• For ceiling mounting follow instructions for horizontal/vertical mounting and angle head accordingly (see Fig 2)

BLANKING INSERTS

• Blanking inserts are supplied that can be cut and attached to the lens to blank out areas of interference as

required i.e. heat sources, public pathways etc.

Fig 5

Ceiling mounting:

• For ceiling mounting follow instructions for horizontal/vertical mounting (see Fig 2) and angle

head accordingly

• Blanking inserts are supplied that can be cut and attached to the lens to blank out areas of

interference as required i.e. heat sources, public pathways etc.

For initial setup of the sensor, turn the time control fully anti-clockwise to the minimum position

and the lux control fully clockwise to the maximum position

After the sensor has been switched on it will take up to 30 seconds to enter into automatic mode

Once in automatic mode, walk test the PIR by moving in front of the sensor at various positions of

the required ﬁeld of view, checking that the luminaire is activated at each point

After the initial setup and walk test have been completed, adjust the time and lux setting to the

desired levels

TEST MODE

For initial setup of the sensor, turn the time control fully anti-clockwise to the minimum position and the lux control fully

clockwise to the maximum position

After the sensor has been switched on it will take up to 30 seconds to enter into automatic mode

Once in automatic mode, walk test the PIR by moving in front of the sensor at various positions of the required field of

view, checking that the luminaire is activated at each point

After the initial setup and walk test have been completed, adjust the time and lux setting to the desired levels

SENSOR SETUP

Note: When making adjustments to the PIR settings ensure the sensor is powered down

Time control: 3 seconds – 30 minutes. Turn the dial clockwise to increase the length of time the luminaire will remain on

Lux control: 5 lux – full daylight. This setting will adjust the ambient light level the sensor will operate at. If you require the

luminaire to operate in brighter conditions turn the dial clockwise (see Fig 6)

Fig 6

Do not exceed the maximum loading requirements as listed below:

Incandescent – 1800W

Fluorescent – 1100W

LED – 200W

MANUAL OVERRIDE

When in auto mode the product will operate to the settings of the lux and time controls

The unit can be manually overridden by switching the power off and on twice within 3 seconds, this will turn the luminaire

on permanently. After 6 hours the unit will revert back to auto mode or the unit can be put back into auto mode at any

time by switching the power off and on once

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.

Irreparable damage will occur if this instruction is not followed

GENERAL

The product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where

facilities exist. Clean with a soft dry cloth only, do not use other materials or solutions which may damage the product

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install in accordance with the current edition of the

IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this product should fail

BLANKING INSERTS

TEST MODE

For initial setup of the sensor, turn the time control fully anti-clockwise to the minimum position and the lux control fully

clockwise to the maximum position

After the sensor has been switched on it will take up to 30 seconds to enter into automatic mode

Once in automatic mode, walk test the PIR by moving in front of the sensor at various positions of the required field of

view, checking that the luminaire is activated at each point

After the initial setup and walk test have been completed, adjust the time and lux setting to the desired levels

SENSOR SETUP

Note: When making adjustments to the PIR settings ensure the sensor is powered down

Time control: 3 seconds – 30 minutes. Turn the dial clockwise to increase the length of time the luminaire will remain on

Lux control: 5 lux – full daylight. This setting will adjust the ambient light level the sensor will operate at. If you require the

luminaire to operate in brighter conditions turn the dial clockwise (see Fig 6)

Fig 6

Do not exceed the maximum loading requirements as listed below:

Incandescent – 1800W

Fluorescent – 1100W

LED – 200W

MANUAL OVERRIDE

When in auto mode the product will operate to the settings of the lux and time controls

The unit can be manually overridden by switching the power off and on twice within 3 seconds, this will turn the luminaire

on permanently. After 6 hours the unit will revert back to auto mode or the unit can be put back into auto mode at any

time by switching the power off and on once

WARNING

This product must be disconnected from the circuit if subjected to any high voltage or insulation resistance testing.

Irreparable damage will occur if this instruction is not followed

GENERAL

The product should be recycled in the correct manner when it reaches the end of its life. Check local authorities for where

facilities exist. Clean with a soft dry cloth only, do not use other materials or solutions which may damage the product

WARRANTY

This product has a warranty of 1 year from date of purchase. Failure to install in accordance with the current edition of the

IEE Wiring Regulations, improper use, or removal of the batch codes will invalidate the warranty. If this product should fail

Note: When making adjustments to the PIR settings ensure the sensor is powered down

Time control: 3 seconds – 30 minutes. Turn the dial clockwise to increase the length of time the

luminaire will remain on

Lux control: 2 lux – full daylight. This setting will adjust the ambient light level the sensor will

operate at. If you require the luminaire to operate in brighter conditions turn the dial clockwise

(see Fig 6)

Do not exceed the maximum load requirements as listed below:

Incandescent - 2000W

Fluorescent - 1000W

LED - 225W

When in auto mode the product will operate to the settings of the lux and time controls

The unit can be manually overridden by switching the power off and on twice within 3 seconds, this

will turn the luminaire on permanently. After 6 hours the unit will revert back to auto mode or the

unit can be put back into auto mode at any time by switching the power off and on once

This product must be disconnected from the circuit if subjected to any high voltage or insulation

resistance testing. Irreparable damage will occur if this instruction is not followed

SENSOR SETUP

LOAD

MANUAL OVERRIDE

WARNING

Fig 6

The product should be recycled in the correct manner when it reaches the end of its life. Check local

authorities for where facilities exist. Clean with a soft dry cloth only, do not use other materials or

solutions which may damage the product

This product has a warranty of 1 year from date of purchase. Failure to install in accordance with

the current edition of the IEE Wiring Regulations, improper use, or removal of the batch codes

will invalidate the warranty. If this product should fail within its warranty period it should be

returned to the place of purchase for a free of charge replacement. ML Accessories does not accept

responsibility for any installation costs associated with the replacement product. Your statutory

rights are not affected. ML Accessories reserve the right to alter product speciﬁcation without prior

notice

GENERAL

WARRANTY

ML Accessories Limited

LU5 5TA

www.mlaccessories.co.uk AKJUN18_V2

ML Accessories OS001B User manual

Brand: ML Accessories

Model: OS001B

Type: User manual

This manual is also suitable for

OS001

The OS001B has a built-in photosensor that allows you to set the light level at which the sensor will turn on.
Adjustable timer lets you set the amount of time that the lights will stay on after motion is detected.
The sensor has a detection range of up to 6 meters and a 120-degree detection angle.
The sensor can be mounted on a wall or ceiling, and it can be used indoors or outdoors.

Download PDF

report

ML Accessories OS001B User manual

This manual is also suitable for

ML Accessories OS001B User manual

Related papers

Other documents