RV-Link WF-CON-LTE Installation guide

Type
Installation guide
WF-CON-LTE
Installation Manual
RV2402
Extender
RV2458
Router
For Technical Assistance, please call (310) 735-2000,
or visit www.magnadyne.com
Patent No.: US 10,622,709 B2
Patent No.: US D855,591 S
Type A
Type B
WF-CON-LTE
Installs Into These Pre Wired Antenna Models
2
Cover Plate
Cover Plate
Screws (2)
RV2402 Extender
Screws (2)
Cable Tie
RV2458 Router
Control Unit
Screws (2)
Whats in the Kit
Recommended Tools
1) #2 Phillips Screwdriver
2) Small Open Ended Adjustable Wrench
3) Rubbing Alcohol
3
RV2458 Router
RV2402 Extender
LTE Paddle Antennas (2)
with Self Adhesive Tape
Be Sure to Read the Entire Manual Before Installation
Cover Plate
Power
Cable
Wire Tie
Ethernet
Cable
RV2458 Router Installation
4
Remove cover plate from wall.
A) Bring Blue Ethernet and Blue Power Cables
through the wall.
B) Carefully cut wire-tie & discard cover plate.
A) Bring Blue Ethernet and Blue Power Cables
through center hole of new cover plate.
B) Screw new cover plate to wall using
original mounting holes.
1 2
3
310 735-2000
RV-Link.com
Connect Blue Ethernet and Blue Power Cables
to RV2458 Control Unit as pictured.
Router Control Unit & Interior
Installation Complete.
WARNING
Do not connect a
computer or electronic
device to Ethernet port.
Will Cause Damage
Bottom View
Roof Repeater Only
5
Mount Router Control Unit to wall near
the new cover plate as pictured using
included screws.
4
RV2458
Control Unit
5
Remove 4 Machine Screws (#10-24 UNC
Threaded) and 4 Lock Washers from housing
on roof. Retain screws for reassembly.
Lift the housing off of base and disconnect
radio and TV cables.
CAREFUL - Do not let cables fall back
through antenna base into vehicle roof.
RV2402 Installation
1A
Type A Antenna Type B Antenna
2
#10-24 UNC
Threaded
Machine
Screws
Lock
Washers
WiFi / LTE
Housing
TV Cable
Radio Cable
Paddle Antenna Connectors
Wi-Fi / LTE
Optional
GPS Port
Housing
Remove Machine Screw (#8-32 UNC Threaded
Pan Head Screw). Retain screw for reassembly.
Twist housing counter clockwise to unlock
from mounting base.
1B
#8-32 UNC Threaded
Pan Head Screw
Attach paddle antenna connectors onto the
2 outside port connectors of the RV2402 Extender
(each marked by a red dot) and secure using
a small open ended adjustable wrench.
CAREFUL - Do not over tighten.
3
Reconnect TV / Radio cables. For Type A
Antenna, Cut Wire tie from Blue Ethernet
Cable connected to the tube.
MAC #
SER#
RV2402 Installation (continued)
Type A Antenna Type B Antenna
5
Wire Tie
Radio Cables
MAC #
SERIAL #
Paddle Antenna Paddle Antenna
Paddle Antenna
Paddle Antenna
LTE Antenna
Position
LTE Antenna
Position
RV-Link Logo
Location
(topside)
Locking Screw Hole
6
TV Cables
Write down the mac address # and serial #
from the label on the back of the RV2402
in the space provided below.
6
A) To create a clean surface for the paddle
antennas, wipe down the inside of the
Wi-Fi / LTE housing with rubbing alcohol.
B) Peel off adhesive back from paddle antennas.
C) Firmly place into interior housing as shown.
IMPORTANT: Paddles should be positioned
opposite from each other for best reception.
A) To create a clean surface for the paddle
antennas, wipe down the inside of the
Wi-Fi / LTE housing with rubbing alcohol.
B) Peel off adhesive back from paddle antennas.
C) Firmly place into interior housing as shown.
IMPORTANT: 1 antenna should line up with
the housing units Locking Screw Hole.
4A 4B
Input: 12V/0.6A
FCC ID: ZGM-RV2402
IC: 23051-RV2402
RV2402
2.4G/5G WiFi & LTE
Multi-Band Extender/Repeater
Made in China
2010000000000000001
MAC:
S/N:
Patent No.:
US D855,591 S
Patent No.:
US 10,622,709 B2
Place RV2402 Roof Repeater into base in
location shown and screw to posts using
included screws.
WARNING Hand tighten with screw driver only
A) Plug Blue Ethernet Cable into RV2402
B) Wire tie Blue Ethernet Cable to center
tube of base. (Type A Antenna)
Roof Repeater unit.
A) Place housing back onto base. Make sure
cables fit securely inside base, are not
pinched, and do not interfere with
RV2402 antennas.
A) Aligning the Housing Locking Screw Hole and
Base Alignment Notch, place housing back
onto base. Make sure cables fit securely
inside base, are not pinched, and do not
interfere with RV2402 antennas.
B) Twist housing clockwise to lock into place and
secure together with the #8-32 UNC Threaded
Pan Head Screw that was removed in Step 1B.
C) Installation complete.
WARNING - Make sure the 0-Ring is in place
and pan head screw is tight.
B) To reassemble, use the 4 Machine Screws
(#10-24 UNC Threaded) and 4 Lock
Washers that were removed in Step 1A.
C) Installation complete.
WARNING - Make sure the O-ring is in
place and screws are tight.
Lock
Locking Screw
Hole
Alignment
Notch
Washers
7
8
9B9A
RV2402
Roof
Repeater
Blue Ethernet
Cable
Wire Tie
Base
#10-24 UNC
Threaded Machine
Screws
#8-32 UNC
Threaded Pan Head Screw
RV2402 Installation (continued)
Type A Antenna
Type B Antenna
7
ONE (1) YEAR LIMITED WARRANTY
Magnadyne Corporation or its authorized agents will within one year from the date of sale to
you, repair, replace or refund the retail sales price of said product or any part thereof, at the
option of the Magnadyne Corporation or its authorized agents, if said product or part is found
defective in materials or workmanship, when properly connected and operating on the correct
power requirements designated for the specific product. This warranty and Magnadyne
Corporation or its authorized agent’s obligations hereunder do not apply where the product
was; damaged while in the possession of the consumer, subjected to unreasonable or
unintended use, not reasonably maintained, utilized in commercial or industrial operations, or
serviced by anyone other than Magnadyne Corporation or its authorized agents, or where the
warning seal on the product is broken or the power and/or plugs are detached from the unit.
Magnadyne Corporation or any of its authorized agents will not assume any labor costs for the
removal and reinstallation of any product found to be defective, or the cost of transportation
to Magnadyne Corporation or its authorized agents. Such cost are the sole responsibility of the
purchaser.
This warranty does not cover the cabinet appearance items or accessories used in connection
with this product, or any damage to recording or recording tape, or any damage to the
products resulting from improper installation, alteration, accident, misuse, abuse or acts of
nature.
MAGNADYNE CORPORATION OR ITS AUTHORIZED AGENTS SHALL NOT BE LIABLE TO
ANYONE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES OR CLAIMS EXCEPT THOSE
ACCORDED BY LAW. NO EXPRESSED WARRANTY OR IMPLIED WARRANTY IS GIVEN
EXCEPT THOSE SET FORTH HEREIN. NO IMPLIED WARRANTY SHALL EXTEND BEYOND ONE
YEAR FROM THE DATE OF SALE.
This warranty extends only to the original purchaser of the product and is not
transferable. Some states do not allow limitations on how long an implied warranty lasts, and
some states do not allow the exclusion or limitation of incidental or consequential damages,
so the above limitations or exclusion may not apply to you. This warranty gives you specific
legal rights, and you may have other rights that vary from state to state.
“NOTE: The manufacturer is not responsible for any radio or TV interference caused by
unauthorized modifications to this equipment. Such modifications could void the User’s
authority to operate the equipment.”
Defective merchandise should be returned to the original point of purchase or
secondly, to Magnadyne Corporation, 1111 W. Victoria Street, Compton CA 90220.
Return Authorization must be obtained before sending, or merchandise may be refused.
Copyright © 2020 Magnadyne Corp.
WF-CON-LTE_IM_Rev. B_04-14-20
Patent No.: US 10,622,709 B2
Patent No.: US D855,591 S
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

RV-Link WF-CON-LTE Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI