Blue Sea Systems SafetyHub 100 7725 User manual

Blue Sea Systems
Brand
Blue Sea Systems
Model
SafetyHub 100 7725
Type
User manual

This manual is also suitable for

PN 7725 / PN 7725B
PN 7725 includes a connector plug for the ATO
®
/ATC
®
fuse circuits
TheBlueSeaSystemsSafetyHub100isanignition-protectedfuseblock
withanintegratedconnectingplug.Itconsolidates1A–200Afuses,andcan
bewireddirectlytothebattery(forunswitchedfuseprotection)orafterthe
batteryswitch(forswitchedfuseprotection).
]Disconnectallbatteryconnectionsbeforebeginningtheinstallation.
]BlueSeaSystemsstronglyrecommendsthatacompetentelectrical
professionalperformtheinstallationofthisproduct.
GUARANTEE:BlueSeaSystemsstandsbehinditsproducts
foraslongasyouownthem.Finddetailedinformationat
www.bluesea.com/about.Forcustomerservice,call800-222-7617.
MarineElectricalProd
ucts
SafetyHub 100 Fuse Block
BlueSeaSystemsInc. p360.738-8230
425SequoiaDrive f360.734-4195
Bellingham,WA98226USA [email protected]
www.bluesea.com
980004720Rev.004
Specications
WARNING
AmperageMaximumOperating(combined) (seetablebelow)
NominalOperatingVoltage 12VDC
MinimumInputCableSizetoMeetRatings 4/0AWG(120mm²)
RecommendedRingTerminal M8(5/16”)
StudSize M8x1.25
StudTorque 15ft-lb(20.3N-m)
AMI
®
/MIDI
®
FuseBlock
AmperageMaximumOperating(perblock) 240A
†
AmperageMaximumOperating(percircuit) 170A
†
FuseAmperagesAvailable 30A–200A
MinimumCableSizetoMeetRatings 2/0AWG(70mm²)
ScrewSize M5x.8x10
ScrewTorque 27in-lb(3.0N-m)
ATO
®
/ATC
®
FuseBlock
AmperageMaximumOperating(perblock) 50A
†
AmperageMaximumOperating(percircuit) 20A
†
FuseAmperagesAvailable 1A–20A
Regulatory
Emarked
MeetsISO8846ignitionprotectionandSAEJ1171externalignitionprotectionrequirements.
IP66—protected against powerful water jets
InputWireSizeandCurrentDeratingTable
†
Ratingsaredependentoninputcablesizedforappropriateamperages.
Unlatchthetwoyellowtabsonthefusecovertoaccessfuses.
TheATO
®
/ATC
®
FuseBlockoftheSafetyHub100isusedforlow-ampcircuits.
Thetotalcontinuousamperageofthisblockmustnotexceed50A.
TheAMI
®
/MIDI
®
FuseBlockoftheSafteyHub100isusedforhigh-ampcircuits.
Thetotalcontinuousamperageofthisblockmustnotexceed240A
AWGWireSize MetricWireSize AmperageMaximumOperating(combined)
4/0AWG 120mm² 280A
2/0AWG 70mm² 225A
1AWG 50mm² 180A
4AWG 25mm² 125A
PN 7725 / PN 7725B
PN 7725 includes a connector plug for the ATO
®
/ATC
®
fuse circuits
TheBlueSeaSystemsSafetyHub100isanignition-protectedfuseblock
withanintegratedconnectingplug.Itconsolidates1A–200Afuses,andcan
bewireddirectlytothebattery(forunswitchedfuseprotection)orafterthe
batteryswitch(forswitchedfuseprotection).
]Disconnectallbatteryconnectionsbeforebeginningtheinstallation.
]BlueSeaSystemsstronglyrecommendsthatacompetentelectrical
professionalperformtheinstallationofthisproduct.
GUARANTEE:BlueSeaSystemsstandsbehinditsproducts
foraslongasyouownthem.Finddetailedinformationat
www.bluesea.com/about.Forcustomerservice,call800-222-7617.
MarineElectricalProd
ucts
SafetyHub 100 Fuse Block
BlueSeaSystemsInc. p360.738-8230
425SequoiaDrive f360.734-4195
Bellingham,WA98226USA [email protected]
www.bluesea.com
980004720Rev.004
Specications
WARNING
AmperageMaximumOperating(combined) (seetablebelow)
NominalOperatingVoltage 12VDC
MinimumInputCableSizetoMeetRatings 4/0AWG(120mm²)
RecommendedRingTerminal M8(5/16”)
StudSize M8x1.25
StudTorque 15ft-lb(20.3N-m)
AMI
®
/MIDI
®
FuseBlock
AmperageMaximumOperating(perblock) 240A
†
AmperageMaximumOperating(percircuit) 170A
†
FuseAmperagesAvailable 30A–200A
MinimumCableSizetoMeetRatings 2/0AWG(70mm²)
ScrewSize M5x.8x10
ScrewTorque 27in-lb(3.0N-m)
ATO
®
/ATC
®
FuseBlock
AmperageMaximumOperating(perblock) 50A
†
AmperageMaximumOperating(percircuit) 20A
†
FuseAmperagesAvailable 1A–20A
Regulatory
Emarked
MeetsISO8846ignitionprotectionandSAEJ1171externalignitionprotectionrequirements.
IP66—protected against powerful water jets
InputWireSizeandCurrentDeratingTable
†
Ratingsaredependentoninputcablesizedforappropriateamperages.
Unlatchthetwoyellowtabsonthefusecovertoaccessfuses.
TheATO
®
/ATC
®
FuseBlockoftheSafetyHub100isusedforlow-ampcircuits.
Thetotalcontinuousamperageofthisblockmustnotexceed50A.
TheAMI
®
/MIDI
®
FuseBlockoftheSafteyHub100isusedforhigh-ampcircuits.
Thetotalcontinuousamperageofthisblockmustnotexceed240A
AWGWireSize MetricWireSize AmperageMaximumOperating(combined)
4/0AWG 120mm² 280A
2/0AWG 70mm² 225A
1AWG 50mm² 180A
4AWG 25mm² 125A
WiringDiagram
InstallationInstructions
Mounting
InstalltheSafetyHub100inareadilyaccessiblelocationascloseaspossibleto
thebattery.Toavoidcorrosiontoconnectingwiresandterminals,mountinadry
andprotectedlocation.Avoidmountingdirectlyaboveventedleadacidbatteries
sothattheSafetyHub100
FuseBlockisnotexposedtocorrosivegassesfrom
thebatteries.Wherepossible,mounttheSafetyHub100
inaverticalorientation.
Forhelpselectingtheappropriatewiresizeandcircuitprotectionrating,referto
theCircuitWizardatwww.circuitwizard.bluesea.com
HighCurrentInputConnection
TousetheSafetyHub100asanunswitchedfuseblock,connectthepositive
batteryterminaldirectlytotheinputstudontheSafetyHub100.Tousethe
SafetyHub100asaswitchedfuseblock,connecttheoutputofthebattery
switchtotheinputstudontheSafetyHub100.TorquetheSafetyHub100input
connectionto15ft-lb.
AMI
®
/MIDI
®
FuseCircuitConnections
Toconnecthigh-amploadssuchasanenginestartingcircuit,distributionpanel,
orwindlass,usethenumberedhigh-ampstuds.
Note: Wires used for engine starting do not require circuit protection.
If you choose not to fuse the engine starting circuit, use the PN 7732 Engine
Circuit Link Bus instead of a AMI
®
/MIDI
®
fuse. Do not use the 7732 Link Bus
for any other purpose.
ATO
®
/ATC
®
FuseCircuitConnections
Toconnectlow-amploadssuchasabilgepump,VHFradio,clockmemory,or
alarm,connecttotheSafetyHub100plugreceiver.PN7725includesawire
harnessfortheseconnections.
CONNECT TO DEVICE
USING ATO
®
/ATC
®
FUSE CONNECTOR PLUG
12V
For unswitched circuit protection the
SafetyHub 100 is connected directly
to the battery
for boats at moorage.
AMI®/ MIDI®FUSE CIRCUITS
ATO
®/ATC®FUSE
CIRCUITS
For switched circuit protection the
SafetyHub 100 is connected after the battery
switch
for trailer or dry storage boats.
CONNECT TO DEVICE
USING ATO
®
/ATC
®
FUSE CONNECTOR PLUG
SWITCHED ATO®/ATC®
FUSE CIRCUITS
CONNECTOR
PLUG
FUSE
COVER
FUSE
COVER
MOUNTING
HOLE
SWITCH
MOUNTING
HOLE
CONNECTOR
PLUG
MOUNTING
HOLE
INPUT
STUD
MOUNTING
HOLE
INPUT
STUD
12V
SWITCHED AMI®/ MIDI®FUSE CIRCUITS
WiringDiagram
CONNECT TO DEVICE
USING ATO
®
/ATC
®
FUSE CONNECTOR PLUG
12V
For unswitched circuit protection the
SafetyHub 100 is connected directly
to the battery
for boats at moorage.
AMI®/ MIDI®FUSE CIRCUITS
ATO
®/ATC®FUSE
CIRCUITS
For switched circuit protection the
SafetyHub 100 is connected after the battery
switch
for trailer or dry storage boats.
CONNECT TO DEVICE
USING ATO
®
/ATC
®
FUSE CONNECTOR PLUG
SWITCHED ATO®/ATC®
FUSE CIRCUITS
CONNECTOR
PLUG
FUSE
COVER
FUSE
COVER
MOUNTING
HOLE
SWITCH
MOUNTING
HOLE
CONNECTOR
PLUG
MOUNTING
HOLE
INPUT
STUD
MOUNTING
HOLE
INPUT
STUD
12V
SWITCHED AMI®/ MIDI®FUSE CIRCUITS
InstallationInstructions
Mounting
InstalltheSafetyHub100inareadilyaccessiblelocationascloseaspossibleto
thebattery.Toavoidcorrosiontoconnectingwiresandterminals,mountinadry
andprotectedlocation.Avoidmountingdirectlyaboveventedleadacidbatteries
sothattheSafetyHub100
FuseBlockisnotexposedtocorrosivegassesfrom
thebatteries.Wherepossible,mounttheSafetyHub100
inaverticalorientation.
Forhelpselectingtheappropriatewiresizeandcircuitprotectionrating,referto
theCircuitWizardatwww.circuitwizard.bluesea.com
HighCurrentInputConnection
TousetheSafetyHub100asanunswitchedfuseblock,connectthepositive
batteryterminaldirectlytotheinputstudontheSafetyHub100.Tousethe
SafetyHub100asaswitchedfuseblock,connecttheoutputofthebattery
switchtotheinputstudontheSafetyHub100.TorquetheSafetyHub100input
connectionto15ft-lb.
AMI
®
/MIDI
®
FuseCircuitConnections
Toconnecthigh-amploadssuchasanenginestartingcircuit,distributionpanel,
orwindlass,usethenumberedhigh-ampstuds.
Note: Wires used for engine starting do not require circuit protection.
If you choose not to fuse the engine starting circuit, use the PN 7732 Engine
Circuit Link Bus instead of a AMI
®
/MIDI
®
fuse. Do not use the 7732 Link Bus
for any other purpose.
ATO
®
/ATC
®
FuseCircuitConnections
Toconnectlow-amploadssuchasabilgepump,VHFradio,clockmemory,or
alarm,connecttotheSafetyHub100plugreceiver.PN7725includesawire
harnessfortheseconnections.
  • Page 1 1
  • Page 2 2

Blue Sea Systems SafetyHub 100 7725 User manual

Blue Sea Systems
Brand
Blue Sea Systems
Model
SafetyHub 100 7725
Type
User manual
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents