Sanuvox S100 User manual

Type
User manual

Sanuvox S100 is an air purification unit designed to reduce airborne contaminants, including biological and chemical pollutants, in various indoor environments. It utilizes an internal fan to circulate air through a UV lamp and filter, effectively removing harmful particles and microorganisms. The unit can be conveniently installed either in a suspended ceiling or on a wall, making it suitable for a wide range of applications, such as offices, schools, hospitals, and public spaces.

Sanuvox S100 is an air purification unit designed to reduce airborne contaminants, including biological and chemical pollutants, in various indoor environments. It utilizes an internal fan to circulate air through a UV lamp and filter, effectively removing harmful particles and microorganisms. The unit can be conveniently installed either in a suspended ceiling or on a wall, making it suitable for a wide range of applications, such as offices, schools, hospitals, and public spaces.

Sanuvox Technologies Inc, © 2020 All rights reserved. July 2023 EN v.12
Instruction Manual
Photos illustrating products are non contractual.
SANUVAIR® S100
AIR PURIFICATION UNIT
Commercial Model
Installation Date: _______________ Installed by: _________________
Installer Contact Info.: _________________________________________
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS PRODUCT.
Read and follow all instructions contained in the manual before using the product. Read the maintenance instructions before opening the UV unit
or system. Failure to comply with these instructions may result in injuries or damage to the UV unit or system.
NEVER EXPOSE EYES OR SKIN TO AN OPERATING UV LAMP.
1. Installation and servicing of UV units or systems (in an
air conditioning system or not) can be hazardous. Only
trained and qualied service personnel should install,
repair or service equipment.
2. Untrained personnel can perform basic maintenance
functions such as replacing lamp(s) and/or lter(s). All
other operations should be performed by trained service
personnel.
3. The unit is not to be used by persons (including children)
with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge.
CAUTION: Unit is not a toy. Keep away from
unsupervised children. Do not leave children unattended
with the unit.
4. DO NOT hang onto the UV unit or system.
5. Some UV units or systems could be heavy: Make sure
you have a minimum of 2 people to safely move or install
these UV units or systems, and make sure you adopt the
most ergonomic position possible (use UV unit or system
handles, if applicable).
CAUTION: Installing or maintaining heavy equipment,
especially overhead, can cause back pain or other injuries.
6. When installing or servicing an overhead UV unit or system,
be careful not to fall off the stepladder. Furthermore, make
sure the UV unit or system latches are always in place to
prevent falling parts.
CAUTION: Some parts of some UV units and systems
may open suddenly if the UV unit or system is installed
high up without its locks.
7. Units that are obviously damaged must not be operated.
8. CAUTION: When working on the UV unit or system,
observe precautions on the literature, tags and labels
attached to the UV unit or system, and all other safety
precautions considered as best practices in the HVAC
industry, if applicable.
9. When applicable, local regulation may comprise more
restrictive installation and/or certication requirements.
The aforementioned requirements prevail on those of this
document and the installer agree to conform to these at his
own expense.
10. Follow all the safety instructions outlined in this document
and respect all local and national codes applicable.
11. All UV units or systems contain a UV-C source. Damage to
the housing or unintended use of the UV unit or system may
result in harmful UV-C leaks. UV-C may, even in little doses,
cause harm to the eyes and skin.
12. Never expose eyes or skin to an operating UV lamp.
Therefore, before installing or performing maintenance
on the UV unit or system, TURN OFF AND DISCONNECT
the UV unit or system from all power sources (there
may be more than one switch to disconnect) and also
disconnect the HVAC system, is applicable.
CAUTION: Electrical shock may cause injuries or
possibly death. FIRST AID INSTRUCTIONS: If injured,
consult a doctor.
13. UV rays may damage certain types of lters (polymer or
plastic); please keep the UV unit or system light away from
shining directly on plastic.
14. When installing or performing maintenance on the UV unit
or system, it is recommended to wear safety gloves. In
order to avoid reduced performance of lamp(s), do not
touch lamp glass without gloves.
15. Just like conventional uorescent lamps, UV lamps contain
a small quantity of mercury: if a lamp breaks, clean and
dispose of with care. UV lamps can be disposed/recycled
after use in the same way as any other uorescent lamps.
Contact and follow the specic instructions of your local
and national authorities.
15.1. Dispose of unit or system according to the specic
instructions and standards of your local and national
authorities.
16. Use only specied SANUVOX branded replacement
UV lamps for your UV unit or system. Use of any other
lamps will void your warranty and can result in damage to
the UV unit or system.
17. Sanuvox UV units or systems are not waterproof. DO NOT
INSTALL OUTDOORS OR IN WET LOCATION unless
specied otherwise.
18. Use of this unit or system supplements, but does not
replace, infection control best practices. Users must follow
all these practices, particularly with regard to cleaning and
disinfecting surfaces.
SAVE THESE INSTRUCTIONS
For any inquiries on a UV unit or system, contact :
Robert Smith
146 Barr St, Saint-Laurent
Quebec, CA, H4T 1Y4
1-888-726-8869
techsupport@sanuvox.com
REGISTER
YOUR WARRANTY
2
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS 1
TABLE OF CONTENTS 2
ABOUT THE PRODUCT 3
COMPONENTS 3
How it Works 3
SETUP & INSTALLATION 3
What you will need 3
What’s included 3
Versatile Installations 4
Step by Step Setup & Installation - Ceiling-Mounted 4
Step by Step Setup & Installation - Wall-Mounted 6
OPERATION 7
How to Operate your Product 7
MAINTENANCE 8
How to Replace the Lamp 8
Step by Step Lamp Replacement 8
How to Clean your Product 9
Step by Step Filter Cleaning 9
STORAGE 10
ULTRAVIOLETS 10
ELECTRICAL RATINGS, POWER CONSUMPTION & AVAILABLE VOLTAGE 10
TROUBLESHOOTING 10
What you will need 10
Problems & Solutions Table 10
Step by Step UV Lamp Continuity Test 11
WARRANTY 12
CUSTOMER SERVICE 12
A
B
D
F
E
G
H
C
3
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
ABOUT THE PRODUCT
Congratulations on the purchase of the SANUVAIR® S100 unit. Sanuvox systems are the most advanced air purication
systems available, that can help reduce biological and chemical contaminants that circulate throughout the building. Sanuvox
systems have been tested by universities, in hospitals and by independant third party laboratories.
For information or recommendations on how to size your specic application, please call SANUVOX at 1-888-726-8869.
COMPONENTS
How it Works
The Sanuvox SANUVAIR® S100 unit is designed to help reduce airborne contaminants. The air purier can be installed in a
suspended celling or on a wall. An internal fan circulates air through the air purier.
A. Air inlet vent
B. Filter door (with mesh)
C. Security switch
D. Filter
E. UV Lamp
F. Fan
G. Unit cover
H. Air outlet vent
SETUP & INSTALLATION
What you will need
A utility knife to unpack all components, a stepladder to reach the celling or wall properly, a Phillips No.2 screwdriver, a measuring
tape, a level, a marker, and a cutter or saw (if ceiling-mounted).
CAUTION: Handle your product with care to avoid breaking parts. Make sure you have a free and safe space to unpack,
install and setup your product. Conrm you have access to the necessary power source for the product requirements (see unit
or system label). If you have any questions regarding the installation instructions, call SANUVOX at 1-888-726-8869.
What’s included
The SANUVAIR® S100, a UV lamp and a basic
installation kit.
The installation kit includes: a pair of cotton gloves,
4-40 screws (3), a AC/DC convertor, a power cord
(US or EUR), an angled support bracket and a
near-horizontal support bracket.
A
AB
B
4
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
Versatile Installations
The SANUVAIR® S100 unit can be installed two ways: ceiling-mounted in a 24" x 14" area of a suspended ceiling at least 8"
deep OR simply wall-mounted.
Either way, make sure there is adequate clearance (at least 2 feet) for the door to swing down for maintenance or service.
Step by Step Setup & Installation - Ceiling-Mounted
1. Check installation location of the unit, so that there is at least 24"
from the wall in order to have good air circulation.
Also make sure you have access to a 120 or 230 VAC input to power
the unit.
2. Prepare unit for installation: Take the unit out of its box and install the
support anchors required to hold the unit by screwing them directly it.
A. Sliding door side : near-horizontal support bracket.
B. Beveled side (mesh) : angled support bracket.
Then lay the unit on a at surface with the access doors facing up.
STEP 1
STEP 2
STEP 5
5. Install lamp: Open the unit by sliding its cover to gain access to the lamp
location. Connect the lamp to the connector (only one way possible)
and gently attach it to the lamp holder.
NOTE: Lamp must be installed over the stopper.
3. Prepare for UV lamp installation: open lamp packaging. Only after
you have visually inspected the UV lamp should you break the security
seal on the underside of the cardboard sleeve.
4. Carefully slide the UV lamp out from the cardboard sleeve. Be sure to
wear the cotton gloves (included) guaranteeing a clean lamp free from
ngerprints.
NOTE: Fingerprints on the lamp will negatively impact the UV output of
the lamp.
STEP 3
STEP 4
min. 24"
Access Doors
5
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
7. Prepare location for installation: Cut a 24" x 14" opening in a
suspended ceiling tile to install the unit. In order to facilitate the work,
remove 14" lengthwise.
8. Make the following connections: Connect the power cable to the
AC/DC convertor, then connect the elbow adapter to the unit.
NOTE: Do not plug the unit into a power outlet until you have
completed the installation. By now you should have connected only
the unit, converter, and power cable together.
STEP 7
STEP 8
STEP 9
STEP 10
9. Pass the unit and its cable assembly through the ceiling (tilt it
slightly to the side) and gently lean the device support anchors against
the tile and the ceiling support.
Make sure to position the unit so that the air outlet (open end) is at least 24"
from the wall, and that the unit cable assembly can reach a power outlet.
10. Replace the cut part of the suspended ceiling tile to hide the opening.
Then, right up against the unit, install a 24" ‘T’ bracket.
Plug in the device: it will turn on automatically.
Your new SANUVAIR® S100 is now ready to
operate so you can enjoy great air quality
for you and your colleagues.
6. Adjust the fan speed: While the unit cover is still open, you will have
access to the speed controller. Depending on your needs, choose
between “Hi”, “Med” or “Low” speeds.
Once the lamp and lter are installed and the fan settings are adjusted
to your liking, make sure to close the unit cover properly.
STEP 6
6
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
Step by Step Setup & Installation - Wall-Mounted
1. Check installation location of the unit, so that there is at least 24"
from the ceiling in order to have good air circulation.
Also make sure you have access to a 120 or 230 VAC input to power
the unit.
STEP 1
2. Prepare unit for installation: Take the unit out of its box and lay the
unit on a at surface with the access doors facing up.
STEP 2
3. Prepare for UV lamp installation: open lamp packaging. Only after
you have visually inspected the UV lamp should you break the security
seal on the underside of the cardboard sleeve.
4. Carefully slide the UV lamp out from the cardboard sleeve. Be sure to
wear the cotton gloves (included) guaranteeing a clean lamp free from
ngerprints.
NOTE: Fingerprints on the lamp will negatively impact the UV output of
the lamp.
STEP 3
STEP 4
STEP 5
5. Install lamp: Open the unit by sliding its cover to gain access to the lamp
location. Connect the lamp to the connector (only one way possible)
and gently attach it to the lamp holder.
NOTE: Lamp must be installed over the stopper.
STEP 6
6. Adjust the fan speed: While the unit cover is still open, you will have
access to the speed controller. Depending on your needs, choose
between “Hi”, “Med” or “Low” speeds.
Once the lamp and lter are installed and the fan settings are adjusted
to your liking, make sure to close the unit cover properly.
min. 24"
7
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
7. Now, prepare location for installation: Mark wall and screw in
support screw at proper height. Support screws should be at the same
height, leveled and 3.5" apart.
Then, hang the unit on the wall on the support screw.
STEP 7
8. Connect the AC/DC convertor supply to the unit.
NOTE: Once connected, the unit will turn on automatically.
Your new SANUVAIR® S100 is now ready
to operate so you can enjoy great air quality
for you and your colleagues.
STEP 8
OPERATION
How to Operate your Product
If wired directly to a dedicated power source, the SANUVAIR® S100 will operate continuously. If wired in parallel with other
devices, such as overhead lighting, the SANUVAIR® S100 will operate only when the circuit is energized. The internal fan
circulates air through the device. Room air is drawn in through the aluminum lter and passes by the ultraviolet lamp. Then, the
puried air is being exhausted. A safety switch is provided to stop operation if the cover is opened.
Do not hold down security switch when cover is open. The ultraviolet lamp will energize, which may cause injury to eyes and
exposed skin. Never expose eyes or skin to direct UV light.
CAUTION: The suggested operating temperature range is 50°F to 115°F (10°C to 46°C). Operating the SANUVAIR® S100
outside this range will result in decreased performance.
8
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
MAINTENANCE
How to Replace the Lamp
Replacing the lamp on the SANUVAIR® S100 needs to be done periodically to maintain design specications. The UV lamp can
function for many years, but over time, the UV intensity does decreases. For best results, the UV lamp should be replaced every
two years guaranteeing the highest performance.
CAUTION: TURN OFF AND DISCONNECT the unit before performing maintenance. In order to avoid reduced performance
of the lamp, do not touch lamp glass without gloves.
Step by Step Lamp Replacement
Example for a ceiling-mounted unit. The same step by step process applies for a wall-mounted unit.
NOTE: The lamp can be replaced while the unit is installed on the ceiling or wall. Another option is to remove the unit from the
ceiling or wall, and then replace the lamp with the unit lying on a at surface with the access doors facing up. Besides, this option
is preferable for a wall unit.
1. Unplug the unit, then open it by sliding down its cover to gain access to
the lamp location.
NOTE: Unit must be disconnected from the supply before replacing
lamp.
3. Prepare the new UV lamp: open lamp packaging. Only after you
have visually inspected the UV lamp should you break the security seal
on the underside of the cardboard sleeve.
4. Carefully slide the new UV lamp out from the cardboard sleeve. Be sure
to wear the cotton gloves (included) guaranteeing a clean lamp free
from ngerprints.
NOTE: Fingerprints on the lamp will negatively impact the UV output of
the lamp.
STEP 1
STEP 3
STEP 4
2. Open the clamp. Disconnect the old UV lamp from the connector and
remove the lamp from the unit.
NOTE: UV lamps can be disposed/recycled after use, as any other
uorescent lamps. Contact and follow your local and national authorities’
specic instructions.
6. Close the unit cover properly.
5. Connect the lamp to the connector (only one way possible) and gently
attach it into the lamp clamp.
NOTE: Lamp must be installed over the stopper.
STEP 2
STEP 6
STEP 5
9
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
How to Clean your Product
There is very little maintenance to be done on the SANUVAIR® S100.
Periodic cleaning of the inlet lter may be performed. Filter media should be cleaned at least once every 6 months for optimal
performance to be kept free of dust and residue deposit. Clean when necessary with mild soap. The lamp may be cleaned once
a year with a microber cloth and isopropyl alcohol. Follow the same instructions and precautions as for lamp replacement. To
clean the unit exterior, use a damp cloth with general purpose detergent. Always spot test the cleaner to make sure it does not
damage the surface.
CAUTION: Under no circumstance should water be sprayed or splashed onto the product.
Step by Step Filter Cleaning
Example for a wall-mounted unit. The same step by step process applies for a ceiling-mounted unit.
NOTE: The lter can be removed for cleaning while the unit is installed on the ceiling or wall. Another option is to remove the unit
from the ceiling or wall, and then access the lter with the unit lying on a at surface with the access doors facing up. Besides,
this option is preferable for a wall unit.
1. Unplug the unit, then open it by sliding its cover. Then, open the lter
access door (the one with mesh) by pulling the side that is not perforated
to gain access to the lter location.
NOTE: Unit must be disconnected from the supply before servicing
lter.
CAUTION: When unit is wall-mounted, its cover may slide down
if not properly locked on open. When you slide the unit cover up,
make sure to push it up and toward the wall until it clips in place and
stays up on its own.
STEP 1
2. Remove the lter and and clean it.
NOTE: The lter can be washed with mild soap.
4. Close the lter door and the unit cover properly.
NOTE: To unlock and slide down the unit cover when the unit is
wall-mounted, pull the unit cover toward you and down. Make sure to
close the unit cover for the unit to restart.
3. When lter is dry, reinstall it in the unit.
STEP 2
STEP 4
STEP 3
The cover must clip in place
inside the unit
A. B.
Open Filter
Access Door
Slide Cover
(and lock it in place)
10
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
STORAGE
The SANUVAIR® S100 is a ceiling or wall-mounted unit working continuously and automatically and therefore, requires no
specic storage.
ELECTRICAL RATINGS, POWER CONSUMPTION & AVAILABLE VOLTAGE
The SANUVAIR® S100 has a power consumption of 25 Watts and requires a 12 VDC, 60 Hz, AC/DC convertor.
See product label to conrm power consumption of your specic unit or system.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CUSTOMER SERVICE FIRST OR SEE YOUR WARRANTY.
DO NOT RETURN THE PRODUCT TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE
PRODUCT OR TAMPER WITH ITS COMPONENTS WITHOUT CONTACTING CUSTOMER SERVICE FIRST. DOING SO
MAY VOID YOUR WARRANTY AND CAUSE PERSONAL INJURY OR DAMAGE TO THE PRODUCT.
TROUBLESHOOTING
If your product is not working properly, refer to the following.
What you will need
A stepladder to reach to celling or wall properly and an ohmmeter.
Problem Possible Cause Solution
You cannot see the “glow" of the UV lamp
through the outlet louvers
- The lamp has failed - Check the wire connections to the ballast
and lamp (plug).
- Check lamp continuity.
See UV Lamp Continuity Test
instructions on page 11.
- Replace lamp
The unit has no power - Connections were not properly done - Check and verify that all wire connections
are properly plugged
- The ballast, transformer or adapter has failed - Replace ballast, transformer or adapter
The fan is not working - Connections were not properly done - Check and verify that all wire connections
are properly plugged
- The fan has failed - Contact your contractor or Sanuvox
customer service for assitance
- The speed controller has failed - Contact your contractor or Sanuvox
customer service for assitance
The unit is making loud noise - The fan or motor has failed - Contact your contractor or Sanuvox
customer service for assitance
Contact your contractor for all your needs in terms of replacement parts:
cover, ballast, transformer, adapter, UV lamp, etc.
ULTRAVIOLETS
Ultraviolet wavelengths (UV) emitted by Sanuvox units and systems are identical to ultraviolets produced by the sun. UVC
damage nucleic acids (DNA/RNA) of microorganisms, which inactivates them. Unlike conventional UV lamps on the market,
Sanuvox units and systems use a patented process that delivers a maximum dose of UV to the moving air stream or surfaces.
CAUTION: Never expose eyes or skin to an operating UV lamp.
11
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
Step by Step UV Lamp Continuity Test
Example for a ceiling-mounted unit. The same step by step process applies for a wall-mounted unit.
NOTE: Its possible to access the lamp while the unit is installed on the ceiling or wall. Another option is to remove the unit from
the ceiling or wall, and then access the lamp with the unit lying on a at surface with the access doors facing up. Besides, this
option is preferable for a wall unit.
1. Unplug the unit, then open it by sliding its cover to gain access to the
lamp location.
NOTE: Unit must be disconnected from the supply before servicing
lter.
3. Using an ohmmeter place 1 probe on 1 of the 4 pins and by sensing
the 3 remaining pins, one should have continuity. Make sure the 2
remaining pins also have continuity. When both sets of pins test good
for continuity, it can be assumed that the lamp is good.
STEP 1
STEP 3
2. Open the clamp. Disconnect the old UV lamp from the connector and
remove the lamp from the unit.
NOTE: Fingerprints on the lamp will negatively impact the UV output of
the lamp. Always use cotton gloves to manipulate UV lamps.
STEP 2
12
Instruction Manual for SANUVAIR® S100
1-888-726-8869www.sanuvox.com
WARRANTY
You should rst read all instructions before attempting to use this product.
For this warranty to be valid, keep a copy of the proof of purchase.
UV lamp 2 years
Ballast 3 years
Fan 1 year
A. This limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to
damage resulting from abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered
manufacturing defects under this warranty.
SANUVOX IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE, ANY IMPLIED WARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.
Some jurisdictions do not allow the exclusion or limitation of incidential or consequential damages or limitation on how long an implied warranty last, so
the above limitations or exclusions may not apply to you. This warranty gives specic legal rights, and you also may have other rights which vary from
jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase.
B. At its option, SANUVOX will repair or replace this product if it is found to be defective in material or workmanship.
C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual.
D. This warranty does not cover the lters, pre-lters or other accessories (if included), except for material or workmanship defects.
Call us toll-free at 1-888-726-8869 or email: info@sanuvox.com
Please be sure to specify product name.
NOTE: IF YOU EXPERIENCE A PROBLEM, PLEASE CONTACT CUSTOMER SERVICE FIRST OR SEE YOUR WARRANTY. DO NOT RETURN THE PRODUCT
TO THE ORIGINAL PLACE OF PURCHASE. DO NOT ATTEMPT TO OPEN THE PRODUCT OR TAMPER WITH ITS COMPONENTS WITHOUT CONTACTING
CUSTOMER SERVICE FIRST. DOING SO MAY VOID YOUR WARRANTY AND CAUSE PERSONAL INJURY OR DAMAGE TO THE PRODUCT.
CUSTOMER SERVICE
FOR ASSISTANCE WITH TROUBLESHOOTING
PLEASE CONTACT YOUR CONTRACTOR OR SANUVOX TECHNICAL SUPPORT
Toll-Free Phone #: 1-888-726-8869
Email: techsupport@sanuvox.com
Website: www.sanuvox.com
Please be sure to specify product name.
TO ORDER REPLACEMENT PARTS
PLEASE CONTACT YOUR CONTRACTOR OR SANUVOX PURCHASING DEPARTMENT
Toll-Free Phone #: 1-888-726-8869
Email: po@sanuvox.com
Website: www.sanuvox.com
Please be sure to specify product name.
Replacement parts for this product
BST12VDC18W 18 W, 12 VDC ballast
LMPRGJ65 T6 6.5" UV ‘J’ lamp
FTR-5 Washable lter with aluminum frame
WARNING: Use only specied SANUVOX branded replacement UV lamps with your unit or system. Use of any other
lamps will void your warranty and can result in damage to the unit, system and/or lamp(s).
REGISTER
YOUR WARRANTY
ONLINE AT
www.sanuvox.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Sanuvox S100 User manual

Type
User manual

Sanuvox S100 is an air purification unit designed to reduce airborne contaminants, including biological and chemical pollutants, in various indoor environments. It utilizes an internal fan to circulate air through a UV lamp and filter, effectively removing harmful particles and microorganisms. The unit can be conveniently installed either in a suspended ceiling or on a wall, making it suitable for a wide range of applications, such as offices, schools, hospitals, and public spaces.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI