Copper Pin
SHINE DECOR HIGH VOLTAGE
LED ROPE LIGHT INSTRUCTIONS
DECOR
SHINE
R
ROHS
1.HOW TO INSTALL POWER CORD/
DIMMER/ RGB CONTROLLER
1-1. Insert Pin into the Light
1-2. Connect Power Cord/ Dimmer/ RGB
Controller
Disconnect power rst.
Locate and identify the
2 or 4(RGB) wires in the
LED strip light on the positive
side with “+” mark. Then line up
the sharp prongs of the pin with
the strip light wires. Gently insert the pin into the LED strip
light making sure to make a solid and correct connection with
the internal wire. Check if the sharp prongs are in the same
direction with the “” mark on the strip light. The pins do not
need to be fully inserted, if you push the pins too far into the
strip, it may cause damage to the wires or cause a short circuit.
Insert rounded prongs of the pin into the power cord/dimmer
controller/RGB controller, LED lights are polarized, if they do not
light up when you rst plug them in, simply unplug the power
cord and turn 180°the power cord as indicated and reconnect the
strip light again.
1-3. Test the Light
Test the strip to make sure the light
works by plugging in the power
supply into an outlet. The lights
should now come on. If the lights do not come on, please
check the rst step again. Always keep the rectier or controller
on power wire, don’t remove them.
DISCLAIMER
Dear customer, these instructions are suggested installation
procedures only, they do not constitute professional installation and
may not necessarily meet all electrical requirements in your state.
Please be reminded that our products covered by our ETL report are
not intended to be eld cutting or splicing, Shine Decor assume no
liabilities occur from improper installation including incorrect
cutting, splicing and damaged waterproof insulation etc.
All of our products are warranted against defects in materials and
workmanship for a period of one year from the date of original
purchase. We provide 1 month hassle-free full refund, 6 month
money back or free replacement and 12 month limited warranty.
Thanks for purchasing our product. Please read the instructions
carefully and keep this instruction paper in safe place, you can also
search Shine Decor on Youtube to nd related videos for guidance.
WARNING
！
Do not cover this product as the covering may cause the light to
overheat and melt or ignite.
Uncoil the light prior to plugging in, test the light's function before
installing or cutting.
This product has a polarized plug (one blade is wider than the
other) as a feature to reduce the risk of electric shock.
Unplug the light before installing or replacing fuses, always keep
the rectier/controller on power wire, don't remove it.
We do not recommend customers to cut, shorten, or splice the light
before consulting a qualied electrician.
Do not connect together more than 150ft (110V-130V strip lights) or
300ft (220V-240V strip lights) to avoid overloading electrical circuits.
Do not mount or support the light in a manner that can damage the
outer jacket or cord insulation. Inspect periodically.
Do not submerge the light in liquids, make sure all the connections
and the plug get waterproofed when used outdoors.
https://www.shine-decor.com/pages/reference-videos
VIDEO DIRECTION LINK
Cutting Mark
2.HOW TO SHORTEN THE LIGHTS
1-4. Seal the Connection Area
Silicone Sealant
If you want to use your strip outdoors, you should waterproof-
ing it by applying silicone adhesive liberally into the inside and
outside of the connected area. Gently press out any
make sure to wipe out excess adhesive, let it dry for 24 hours. In
addition, you can cut o about two inch of the heat shrink
tubing, and then slide it over the connected area. Then use the
heat gun/ heat pencil/ lighter to heat up the tubing to create
the seal.
2-1. Make the Cut
Disconnect power before you make
any cutting. Find cut point on the
strip light, take either heavy duty
scissors or shears and line it up
perpendicularly and cut exactly at the cutting mark. If you cut
the light anywhere else, the internal circuit will be damaged and
the light will not illuminate within the interrupted section that
has been severed.
2-2. Test the Light (see 1-3)
2-3. Seal the Connection Area (see 1-4)
3. HOW TO MOUNT THE LIGHT
Mounting Clip
Mounting Clip
End Cap
4.HOW TO SPLICE TWO RUNS
4-1. Connect Middle Connector
The middle connector is prepared for your needs to connect 2 light
segments using only one power supply. Disconnect power rst,
line up the sharp prongs of the pins inside the middle connector
with the strip light wires, then gently insert each pin into each
light. The pins do not need to be fully inserted, if you push the pins
too far into the strip, it may cause damage to the wires or cause a
short circuit.
4-2. Test the Light (see 1-3)
4-3. Seal the Connection Area (see 1-4)
1. Fix mounting clips with screws onto surfaces and snap rope
light into place.
2. Do not bend the light to a diameter less than 8cm on any
individual plane. Do not bend the light to sharp angles or make
repeated and continuous bending as this may damage circuit
traces.
4.HOW TO SPLICE TWO RUNS
5-1. Remote Pairing
5-2. Remote Unpairing
brightness
up button
brightness
down
button
1. switch o the power
2. hold down the brightness up button
for 5 seconds
3. switch on ther power
4. led start ashing showing your remote
is now fully paired to the controller
5. try the remote to see if it's working
5. HOW TO PAIR AND UNPAIR YOUR
REMOTE TO CONTROLLER
When the remote is not working and LED is ashing in an
uncontrolled way, it’s probably because the remote is inadvert-
ently paired to a nearby object and become unpaired from the
controller.
Note: You can use one remote to control several lights once
you’ve paired this one remote to each controller individually. You
can also use individual remote to control individual controller.
1. switch o the power
2. hold down the brightness down button for 5 seconds
3. switch on the power
4. led start ashing showing your remote is now unpaired from the
controller
5. try the remote to see if it’s working
Visit our website and contact us for more
help.
Website: www.shine-decor.com
Email: info@shine-decor.com
/
