Cordelia Lighting EV1011C5C-06 Installation guide

Questions, problems, missing parts? Before returning to the store,

call Envirolite Customer Service

8 a.m. – 6 p.m., EST, Monday – Friday

1-800-345-0542

CLED1011A-06

LED CEILING FLUSH MOUNT

SAFETY INFORMATION

 Before starting installation of this

fixture or removal of a previous

fixture, disconnect the power by

turning off the circuit breaker or by

removing the fuse at the fuse box.

 Consult a qualified electrician if you have any electrical questions or need to

replace the driver.

 If you have any non-electrical questions about this fixture, please contact our

Customer Service Team at 1-800-345-0542.

WARNING: Disconnect the

power prior to removing or

installing a light fixture.

PLANNING THE INSTALLATION

NOTE: Keep your receipt and

these instructions for Proof of

Purchase.

Read all instructions before assembly and installation. Before starting installation

of the fixture or removal of a previous fixture, disconnect the power by turning off

the circuit breaker or by removing the fuse at the fuse box. To avoid damaging

this product, assemble it on a soft, non-abrasive surface such as carpet or

cardboard.

TOOLS REQUIRED

2

Phillips

Screwdriver

Wire

Cutter

Wire

Stripper

Ladder

Safety

Goggles

Electrical

Tape

3

Part

Description

Quantity

AA

Acrylic Shade

1

BB

Fixture Pan

1

CC

Hex Nut

1

DD

Wire Nut

3

EE

Thumb Nut

1

FF

Washer

1

GG

Mounting Screw

2

HH

Nipple

1

II

Quick Connector

1

JJ

Mounting Bracket

1

PACKAGE CONTENTS (not to scale)

AA

BB

EE

JJ II

HH GG FF

CC DD

INSTALLATION

 Insert the quick connector (II) into

the back of the fixture pan (BB).

 Attach the black supply wire to the

black quick connector (II) wire using

a wire nut (DD).

 Attach the white supply wire to the

white quick connector (II) wire using

a wire nut (DD).

 Connect the fixture ground wire and

the supply ground wire together

using a wire nut (DD).

 Wrap all wire connections with

electrical tape for a more secure

connection.

 Carefully tuck all the wires and wire

connections into the outlet box.

 Align the fixture pan (BB) over the

outlet box and feed the mounting

screws (GG) through the holes on

the fixture pan (BB) and into the

outlet box.

 Tighten the mounting screws (GG)

so that the fixture pan (BB) is

secured flush against the ceiling.

1A

2A

4

NOTE: If you have electrical

questions consult your local

electrical code for approved

grounding methods.

II

DD

BB

GG

INSTALLATION (continued)

3A

 Slide the acrylic shade (AA) onto

the fixture pan (BB) and turn it

clockwise until secure.

1B

 Slide the acrylic shade (AA) onto

the fixture pan (BB) and turn it

clockwise until secure.

5

AA

BB

CC

JJ

GG

HH

INSTALLATION (continued)

2B

 Insert the quick connector (II) into

the back of the fixture pan (BB).

 Attach the black supply wire to the

black quick connector (II) wire

using a wire nut (DD).

 Attach the white supply wire to the

white quick connector (II) wire

using a wire nut (DD).

 Connect the fixture ground wire

and the supply ground wire

together using a wire nut (DD).

 Wrap all wire connections with

electrical tape for a more secure

connection.

3B

 Align the center of the fixture

(BB) over the nipple (HH) and

place a rubber washer (CC) over

the nipple (HH).

 Insert and tighten the thumb nut

(FF).

 Slide the acrylic shade (AA) onto

the fixture pan (BB) and turn it

clockwise until secure.

6

II

DD

BB

HH

BB

EE

FF

HH

EXTERIOR MAINTENANCE

 Use a dry or slightly dampened

clean cloth and wipe the surface

of the fixture.

INTERIOR MAINTENANCE

 Disconnect power to the fixture by turning off the circuit breaker or by

removing the fuse at the fuse box.

 Use a dry or slightly dampened clean cloth to wipe the interior surface of the

fixture.

NOTE: Do not use any cleaners

with chemicals, solvents, or harsh

abrasives. Use only a dry soft

cloth to dust or wipe carefully.

CARE & CLEANING

7

 Turn on power at the circuit breaker or fuse box.

 Turn the light switch on to activate the fixture.

OPERATION

TROUBLESHOOTING

Problem

Solution

The

light will not turn on.



Make sure the power supply is on.



Test or replace the switch.



Check the wiring.

The

fuse blows or circuit breaker

trips when light is turned on.



Check the wire connections

WARRANTY

8

WHAT IS COVERED

The manufacturer warrants this lighting fixture to be free from defects in materials

and workmanship for a period of five (5) years from date of purchase. This

warranty applies only to the original consumer purchaser and only to products

used in normal use and service. If this product is found to be defective, the

manufacturer’s only obligation, and your exclusive remedy, is the repair or

replacement of the product at the manufacturer’s discretion, provided that the

product has not been damaged through misuse, abuse, accident, modifications,

alterations, neglect or mishandling.

WHAT IS NOT COVERED

This warranty shall not apply to any product that is found to have been improperly

installed, set-up, or used in any way not in accordance with the instructions

supplied with the product. This warranty shall not apply to a failure of the product

as a result of an accident, misuse, abuse, negligence, alteration, or faulty

installation, or any other failure not relating to faulty material or workmanship.

This warranty shall not apply to the finish on any portion of the product, such as

surface and/or weathering, as this is considered normal wear and tear.

The manufacturer does not warrant and specially disclaims any warranty, whether

expressed or implied, of fitness for a particular purpose, other than the warranty

contained herein. The manufacturer specifically disclaims any liability and shall

not be liable for any consequential or incidental loss or damage, including but not

limited to any labor/expense costs involved in the replacement or repair of said

product.

9

FCC NOTICE

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference

that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following

measures:

□ Reorient or relocate the receiver antenna.

□ Increase the separation between the equipment and receiver.

□ Install the product onto on a circuit different from that to which the receiver is

connected.

□ Consult with the dealer or an experienced radio/TV technician for help.

CAUTION: Any changes made to the electronics circuit will void this equipment’s

compliance with Part 15 of the FCC Rules and should not be operated.

_____________________________

Conforms to standard CAN-ICES 005(B) / NMB-005 (B)

Page is loading ...

Cordelia Lighting EV1011C5C-06 Installation guide

This manual is also suitable for

Cordelia Lighting EV1011C5C-06 Installation guide

in other languages

Related papers

Other documents