Hampton Bay 5LGZ1319-80 Installation guide

Brand: Hampton Bay

Model: 5LGZ1319-80

Type: Installation guide

USE AND CARE GUIDE

Model # 5LGZ1319-80

Toulon 10 ft x 8 ft Steel Pergola with Flat Roof

THANK YOU

1-855-HD-HAMPTON

HAMPTONBAY.COM

to continually create quality products designed to enhance your home. Visit us online to see our full line of products available

for your home improvement needs. Thank you for choosing Hampton Bay!

Questions, problems, missing parts? Before returning to the store,

call Hampton Bay Customer Service

8.00 a.m. - 7.00 p.m. E ST, Monday - Friday,

9.00 a.m. - 6.00 p.m. E ST, Saturday

pergola.

Table of Contents

Safety Information

WARNING:

of any foreign

WARNING: This pergola is NOT a permanent structure and is designed for sunshade and privacy and must be used under normal weather

conditions. We recommend removal of the fabric canopy in windy conditions as gazebos catch wind similar to umbrellas. You must however

completely disassemble the unit prior to any severe weather conditions such as thunderstorm, hurricane, and/or heavy wind and rain.

Failure to remove the fabric canopy or disassemble the unit will cause the pergola to have structure damage or even structural collapse.

CAUTION: Always install on level ground utilizing ground stakes. Do not permanently anchor unit to wood deck or

CAUTION: The pergola fabrics are water resistant but not water proof and may leak during precipitation. Fabrics will fade from direct

exposure to sunlight.

CAUTION: Keep all children and pets away from assembly area.

Begin assembly not less than 6 feet from any obstruction such as fence, garage, house, overhanging branches, clothes line or electrical wires.

Some parts may contain sharp edges, wear protective gloves if necessary. At least two or more people are recommended for safe assembly.

concrete surface.

2/12

Table of Contents........................................................2

Safety Information.......................................................2

Warranty ...................................................................... 2

One Year Frame and Fabric Limited Warranty............................ 2

Pre-Assembly ............................................................3

Planning Assembly... ................................................................3

Package Contents ....................................................................

Assembly ....................................................................4

................................................................ 2

What Is Covered

What Is Not Covered

................................................................ 2 ..

.... ..

Care Instructions... ................................................................ 2..

Warranty

ONE YEAR FRAME AND FABRIC LIMITED WARRANTY

WHAT IS COVERED

WHAT IS NOT COVERED

It remains the customer’s responsibility for freight and packaging charges to and from our service center. This warranty does not cover

We reserve the right to make substitutions with similar merchandise, if the model in question is no longer in production.

You may contact our customer service department with any questions by phone at 1-855-HD-HAMPTON or visit www.hamptonbay.com.

Care Instructions

Before using, wipe with a clean, dry cloth. Do not use bleach or solvents. Treat the frame with liquid wax for maximum protection against

UV light and salty, damp air. Wash the canopy with a mild solution of soap and water, rinse thoroughly, air dry completely.

Please properly tighten all hardware and perform periodic inspections during usage for cracked welds or loose nuts or bolts.

We warrant the frame and fabric to be free of manufacturing defects to the original purchaser for one year.

NOTE: Hardware not shown to actual size.

3/12

Pre-Assembly

PLANNING

ASSEMBLY

It will take two people about 35 minutes to complete the assembly process.

A Philips screwdriver, a freestanding ladder and a rubber mallet are needed.

HARDWARE INCLUDED

Part Description

Bolt (M6x16)

Quantity

AA 32

Bolt (M6x30)

Bolt (M6x75)

Hex wrench (S4)

Bolt (12x29/M6x16)

Self tapping screw (ST4.2x20)

GG Bolt cap 51

HH Stake 8

II 1Hex wrench (S6)

JJ 12Screw (M5x15)

4/12

Pre-Assembly

Part Description Quantity

A 2

C 4

PACKAGE CONTENTS

Corner post

Post top ornament

D 4

Post base ornament

E 4

Post base

Rear side beam

H 2

Short cross beam

Part

Description Quantity

Short side beam with rail

Fixed pole

Guide pole

Pole receiver

Canopy pull

Short cross beam w/o rail

Central beam with rail

Canopy

Front side beam

Front side beam 1

B 2

Corner post

12/5

Assembly

Assembling corner posts

□

Slide post top ornament (C) followed by post base ornamment (D) up from the bottom on each corner post (A/B).

Secure the post top ornament (C) to the top of the corner post with screws (EE) using a Philips Screwdriver.

□

Attach the post base (E) to the bottom of corner post (A/B) with bolts (AA) using a Philips Screwdriver.

□

EE (16)

AA (12)

12/6

Assembly

Assembling long side beams

□

Plug the rear side beam (G) into the rear side beam (F) and secure them with bolts (AA) using hex wrench (FF). (Fig.2.1)

Attach two pole receivers (Q) onto one of the front side beams (F1,G1) with bolts (AA) using hex wrench (FF). (FIg.2.2)

□

Bolt (M6x16)

AA (8)

□

Plug the front side beam (G1) into the front side beam (F1) and secure them with bolts (AA) using hex wrench (FF). (Fig.2.2)

GG (8)

Attach one short cross beam (H) onto the top of two adjacent corner posts (A) and (B) with bolts (CC) using hex wrench (FF). (Fig.3.1)

Repeat this for the other short cross beam.

Assembly

Attaching short cross beams

□

CC (8)

Bolt (M6x75)

12/7

GG (8)

Attach the complete rear side beam (F/G) onto the top of corner posts with one bolt (CC) at each corner.

Attach the complete rear side beam (F/G) to the short side beams (H) with two bolts (DD) at each outside corner using hex wrench (II).

Assembly

Attaching long side beams

□

CC (4)

Bolt (M6x75)

DD (8)

Bolt (12x29/M6x16)

12/8

Follow the above proceedures for the complete front side beam (F1/G1).

□

GG (4)

Attach the short side beams with rail (J) onto the top of the assembled long beams with bolts (CC) and bolts (AA) using hex wrench (FF).

Assembling the roof frame (1)

□

Assembly

12/

J (2)

CC (4)

Bolt (M6x75)

Bolt (M6x16)

AA (4)

GG (8)

K(1)

I (2)

Assembly

Assembling the roof frame (2)

□

Attach the central beam (K) onto the top of the complete side beams (F_G, and F1_G1) with bolts (AA) using hex wrench (FF).

Attach the short side beams (I) onto the the complete side beams (F_G, and F1_G1) with bolts (AA) using hex wrench (FF).

□

12/10

Inserting poles into the canopy

□

Insert poles (L) and (M) into the canopy (P) from each end. Do not Join the two parts into one until step 8.

Insert poles (N) and (O) into the center of the canopy (P). Do not join the two poles before setting the canopy fabric on the frame.

□

Bolt (M6x16)

AA (12)

IMPORTANT:

Please put the ring (1) which is inside the rail of

the beam (K) on the (F1_G1) side where

the pole receivers (Q) are installed.

GG (12)

Assembly

12/11

Attaching the canopy fabric

Secure the assembled poles (L) and (M) onto the long beams without the pole receivers (Q) with bolts (BB) using hex wrench (FF). (Fig.8.1)

On both short sides of the pergola, tie the canopy to the rings inside the rails of the side cross beams (J) with the elastic band (2). (Fig.8.2)

Secure poles (N) and (O) onto the rings inside the rails of the side cross beams (J) with bolts (AA) using hex wrench (FF). (Fig.8.2)

Allow the poles (N) go through the rings inside the rails of the central beams (K) and insert into the poles (O). (Fig.8.3)

Hook the canopy pull (R) in the small hole of the ring (1) which is nearest to the pole receivers (Q).(Fig.8.4)

Hammer ground stakes (HH) into the post bases to stabilize the pergola. (Fig.8.5)

You can adjust the canopy coverage by pulling the canopy pull (R) forward or backward.

When the ﬁrst pole (which goes through ring (1) ) clicks into the pole receivers (Q), the canopy is fully extended.

(Fig. 8.2)

(Fig. 8.5)

L,M

F, G

(Fig. 8.3)

(Fig. 8.1)

AA (8)

BB (3)

Bolt (M6x16)

Bolt (M6x30)

Fig. 8.4

□

Cover all the bolts with bolt caps (GG).

GG (11)

Bolt caps

Assembly

Placement of the canopy pull

12/12

□

For clean look, when the canopy is fully extened, please take down the canopy pull (R) and hook it on corner post (A). Fig.9.1)

When the canopy is fully folded, set the hook on side beam (G). (Fig.9.2)

(Fig. 9.1)

(Fig. 9.2)

Hampton Bay 5LGZ1319-80 Installation guide

Brand: Hampton Bay

Model: 5LGZ1319-80

Type: Installation guide

Download PDF

report

Hampton Bay 5LGZ1319-80 Installation guide

Hampton Bay 5LGZ1319-80 Installation guide

Related papers

Other documents