Page is loading ...
Inside US: +1 (877) 432-9908 Bulletin No. CRA AD 07-A
Outside US: +1 (717) 767-6511 Drawing No. LP1038
www.redlion.net Effective 2017-09-26
-1-
ModelCRA000AD07070000‐G307KtoCRx00007AdapterPlateBulletin
GENERALDESCRIPTION
The Model CRA000 AD070 70000 adapter plate provides the
necessary hardware to install a CRx000 07 into an existing G307K2
cutout. This panel is made out of black Polycarbonate plastic that
matches the material used on the CRx00007 HMI. Included in the kit are
the adapter plate (with pre-attached gasket) and a mounting stiffener/
plate required to meet any NEMA 4X/IP65 (Face only) application.
DIMENSIONSIninches(mm)
INSTALLATIONPROCEDURE
1. Ensure the gasket on the CRx00007 is properly in place. Slide the
CRx00007 through the adapter plate and then through the front of the
cutout in the existing panel. The CRx00007 sits in a recess in the
adapter plate. The adapter plate sits in the cutout.
2. Discard the mounting plate shipped with the CRx00007. Place the
mounting plate shipped with the adapter plate on the rear of the
CRx00007 from the inside of the cutout.
3. Hook the clamps to the slots in the CRx00007 assembly and position
the screws in the anti-walk features provided on the plate. See
diagram below.
4. Tighten the screws against the mounting plate. The minimum torque to
ensure a NEMA 4X/IP65 water seal is 4.0 lbf-in (0.45 Nm). The
maximum torque is 5.0 lbf-in (0.57 Nm).
CAUTION: DO NOT OVER TIGHTEN THE CLAMPS.
After Installation Front View
After Installation Back View
ORDERINGINFORMATION
1
Contact your Red Lion distributor or visit our website for selection of SD
cards, adapters and cables.
CRA000AD07070000
7.90 (200.55)
5.77
(146.62)
7.06 (179.32)
4.87
(123.67)
0.21
(5.46)
0.33
(8.38)
MODEL NO. DESCRIPTION PART NUMBER
CRA000 Adapter Plate from Kadet 7 to CRx000 07 CRA000 AD070 70000
Existing Panel
with G307K
Cutout
Adapter Plate
with Gasket
CRx000 07
Mounting
Plate
Mounting
Clamps
Panel Gasket
SCREW ANTI-WALK
FEATURE
-2-
Bulletin No. CRA AD 07-A Effective 2017-09-26
Drawing No. LP1038
LIMITED WARRANTY
(a) Red Lion Controls Inc., (the “Company”) warrants that all Products shall be free from defects in material and
workmanship under normal use for the period of time provided in “Statement of Warranty Periods” (available at
www.redlion.net) current at the time of shipment of the Products (the “Warranty Period”). EXCEPT FOR THE ABOVE-
STATED WARRANTY, COMPANY MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE
PRODUCTS, INCLUDING ANY (A) WARRANTY OF MERCHANTABILITY; (B) WARRANTY OF FITNESS FOR A
PARTICULAR PURPOSE; OR (C) WARRANTY AGAINST INFRINGEMENT OF INTELLECTUAL PROPERTY
RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW, COURSE OF DEALING, COURSE OF
PERFORMANCE, USAGE OF TRADE OR OTHERWISE. Customer shall be responsible for determining that a
Product is suitable for Customer’s use and that such use complies with any applicable local, state or federal law.
(b) The Company shall not be liable for a breach of the warranty set forth in paragraph (a) if (i) the defect is a result
of Customer’s failure to store, install, commission or maintain the Product according to specifications; (ii) Customer
alters or repairs such Product without the prior written consent of Company.
(c) Subject to paragraph (b), with respect to any such Product during the Warranty Period, Company shall, in its
sole discretion, either (i) repair or replace the Product; or (ii) credit or refund the price of Product provided that, if
Company so requests, Customer shall, at Company’s expense, return such Product to Company.
(d) THE REMEDIES SET FORTH IN PARAGRAPH (c) SHALL BE THE CUSTOMER’S SOLE AND EXCLUSIVE
REMEDY AND COMPANY’S ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET FORTH
IN PARAGRAPH (a).
/