Graco 406808A Owner's manual

Graco
Brand
Graco
Model
406808A
Type
Owner's manual

This manual is also suitable for

Graco 406808A, Overmolded Diaphragm Kits 24B625 and 24B626, Husky 1050 are designed for use with Husky 1050 Air-Operated Diaphragm Pumps. These kits include everything you need to replace the diaphragms on your pump, including two diaphragms, two setscrews, one diaphragm install tool, and eight PTFE O-rings.

The diaphragms are made of either neoprene or PTFE, and they are overmolded for strength and durability. The setscrews are made of stainless steel, and the diaphragm install tool is made of plastic. The O-rings are made of PTFE, and they are used to seal the manifold.

Graco 406808A, Overmolded Diaphragm Kits 24B625 and 24B626, Husky 1050 are designed for use with Husky 1050 Air-Operated Diaphragm Pumps. These kits include everything you need to replace the diaphragms on your pump, including two diaphragms, two setscrews, one diaphragm install tool, and eight PTFE O-rings.

The diaphragms are made of either neoprene or PTFE, and they are overmolded for strength and durability. The setscrews are made of stainless steel, and the diaphragm install tool is made of plastic. The O-rings are made of PTFE, and they are used to seal the manifold.

GENUINE GRACO PARTS AND ACCESSORIES
Overmolded Diaphragm
Kits 24B625 and 24B626
Husky
®
1050 Diaphragm Pumps
406808A
Kit 24B625, Neoprene
®
Kit 24B626, PTFE
Important Safety Instructions
Read all warnings and instructions in the
Husky
®
1050 Air-Operated Diaphragm Pump
Repair/Parts manual. Save all instructions.
Ref. Description Qty.
101 DIAPHRAGM, material shown at left 2
102 SETSCREW, stainless steel 2
104 TOOL, diaphragm install 1
105 O-RING, manifold, PTFE (not shown) 8
Rounded side faces diaphragm.
1
Apply lithium-based grease.
2
Apply permanent (red) Loctite
®
or equivalent to
diaphragm side threads (if screw was removed or
replaced). Apply primer and medium-strength (blue)
Loctite
®
or equivalent to shaft side threads. Screw
into shaft hand-tight.
3
AIR SIDE markings on diaphragm must face center
housing.
4
ti14037a
1
2
102
101
3
4
104
Graco Inc. P.O. Box 1441 Minneapolis, MN 55440-1441
406808 Rev, A 08/2009
Copyright 2009, Graco Inc. is registered to ISO 9001
See reverse for assembly instructions.
2 406808A
Assembly
1. Clamp the shaft flats in a vise.
2. Assemble the air side plate onto the diaphragm. The
rounded side of the plate must face the diaphragm.
3. Apply medium-strength (blue) Loctite or equivalent
to the threads of the diaphragm assembly. Screw
the assembly into the shaft as tight as possible by
hand.
4. Apply lithium-based grease to the shaft u-cups (in
center housing) and the length and ends of the dia-
phragm shaft. Slide the shaft into the housing.
5. Reattach the first fluid cover. Follow Torque
Instructions in the manual.
6. Repeat Steps 2 and 3 for the other diaphragm
assembly.
7. To ensure proper seating and extend diaphragm life,
attach the second fluid cover with air pressure on
the pump.
a. Place the supplied tool (104) where the air valve
gasket normally goes. Arrows (A) must face
toward the fluid cover that is already attached.
b. Reattach the air valve.
c. Supply a minimum of 20 psi (0.14 MPa,
1.4 bar) air pressure to the air valve. Shop air
may be used. The diaphragm will shift so the
second fluid cover will seat properly. Keep air
pressure on until the second fluid cover is
attached.
d. Attach the second fluid cover. Follow Torque
Instructions in the manual.
e. Remove the air valve and the tool (104), replace
the gasket, and reattach the air valve. Follow
Torque Instructions in the manual.
NOTE: If you are replacing the diaphragms but not the
air valve, you must remove the air valve and gasket, put
the tool in place of the gasket, and put the air valve back
on to get the air pressure needed for proper installation
of the second fluid cover. Remember to remove the tool
and replace the gasket when finished.
8. Reassemble the ball check valves and manifolds as
explained in the manual.
A
104
ti14120a
  • Page 1 1
  • Page 2 2

Graco 406808A Owner's manual

Graco
Brand
Graco
Model
406808A
Type
Owner's manual
This manual is also suitable for

Graco 406808A, Overmolded Diaphragm Kits 24B625 and 24B626, Husky 1050 are designed for use with Husky 1050 Air-Operated Diaphragm Pumps. These kits include everything you need to replace the diaphragms on your pump, including two diaphragms, two setscrews, one diaphragm install tool, and eight PTFE O-rings.

The diaphragms are made of either neoprene or PTFE, and they are overmolded for strength and durability. The setscrews are made of stainless steel, and the diaphragm install tool is made of plastic. The O-rings are made of PTFE, and they are used to seal the manifold.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents