Behringer Europower PMP1680S User manual

Brand: Behringer

Model: Europower PMP1680S

Category: Mixers

Type: User manual

This manual is also suitable for

User Manual

EUROPOWER

PMP1680S/PMP980S/PMP960M

1600/900-Watt 10/6-Channel Powered Mixer with

Dual Multi-FX Processor and FBQ Feedback Detection System

2 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

Thank you

Thank you for choosing one of the PMP series powered mixers from BEHRINGER.

These mixers pack impressive features such as digital eects, graphic EQs,

FBQfeedback destroyer and unique voice cancelling function – all in a

lightweight, portable package. You now have a versatile combination of inputs,

routing options, eects and power amp operations for your rehearsal space,

smallvenue or portable PA needs. But why bother with manuals? We know

you want to get started right away, but please read this manual carefully and

keep it handy for ongoing reference. These instructions show you all the inside

features, tricks, and tips you need to build the best possible sound with your new

PMPpowered mixer.

After all, it’s all about your sound.

Table of Contents

Thank you .......................................................................2

Important Safety Instructions ...................................... 3

Legal Disclaimer ............................................................. 3

Limited warranty ............................................................ 3

1. Before you get Started .............................................. 4

1.1 Shipment ................................................................................ 4

1.2 Initial operation ................................................................... 4

1.3 Online registration ............................................................. 4

1.4 The manual ........................................................................... 4

2. Control Elements ....................................................... 6

2.1 Mono and stereo channels .............................................. 6

2.2 Eects section ..................................................................... 6

2.3 Main and monitor section ............................................... 6

2.4 Rear panel ............................................................................. 7

3. Digital Eects Processor ........................................... 8

4. Installation ................................................................. 8

4.1 Mains connection ............................................................... 8

4.2 Audio connections ............................................................. 8

4.3 Loudspeaker connection ................................................. 9

5. Wiring Examples ...................................................... 10

6. Specications ........................................................... 12

3 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

Important Safety

Instructions

LEGAL DISCLAIMER

LIMITED WARRANTY

Terminals marked with this symbol carry

electrical current of su cient magnitude

to constitute risk of electric shock.

Use only high-quality professional speaker cables with

¼" TS or twist-locking plugs pre-installed. Allother

installation or modi cation should be performed only

by quali edpersonnel.

This symbol, wherever it appears,

alertsyou to the presence of uninsulated

dangerous voltage inside the

enclosure-voltage that may be su cient to constitute a

risk ofshock.

This symbol, wherever it appears,

alertsyou to important operating and

maintenance instructions in the

accompanying literature. Please read the manual.

Caution

To reduce the risk of electric shock, donot

remove the top cover (or the rear section).

No user serviceable parts inside. Refer servicing to

quali ed personnel.

Caution

To reduce the risk of  re or electric shock,

do not expose this appliance to rain and

moisture. The apparatus shall not be exposed to dripping

or splashing liquids and no objects  lled with liquids,

suchas vases, shall be placed on the apparatus.

Caution

These service instructions are for use

by quali ed service personnel only.

Toreduce the risk of electric shock do not perform any

servicing other than that contained in the operation

instructions. Repairs have to be performed by quali ed

servicepersonnel.

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as

radiators, heat registers, stoves, or other apparatus

(including ampli ers) that produce heat.

9. Do not defeat the safety purpose of the polarized

or grounding-type plug. A polarized plug has two blades

with one wider than the other. A grounding-type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety. Ifthe

provided plug does not  t into your outlet, consult an

electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Use only attachments/accessories speci ed by

themanufacturer.

12. Use only with the

cart, stand, tripod, bracket,

or table speci ed by the

manufacturer, orsold with

the apparatus. When a cart

is used, use caution when

moving the cart/apparatus

combination to avoid

injury from tip-over.

13. Unplug this apparatus during lightning storms or

when unused for long periods of time.

14. Refer all servicing to quali ed service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power supply cord or plug

is damaged, liquid has been spilled or objects have fallen

into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

beendropped.

15. The apparatus shall be connected to a MAINS socket

outlet with a protective earthing connection.

16. Where the MAINS plug or an appliance coupler is

used as the disconnect device, the disconnect device shall

remain readily operable.

TECHNICAL SPECIFICATIONS AND APPEARANCES

ARE SUBJECT TO CHANGE WITHOUT NOTICE AND

ACCURACY IS NOT GUARANTEED. BEHRINGER,

KLARKTEKNIK, MIDAS, BUGERA, AND TURBOSOUND

ARE PART OF THE MUSIC GROUP MUSICGROUP.COM.

ALL TRADEMARKS ARE THE PROPERTY OF THEIR

RESPECTIVE OWNERS. MUSICGROUP ACCEPTS NO

LIABILITY FOR ANY LOSS WHICH MAY BE SUFFERED

BY ANY PERSON WHO RELIES EITHER WHOLLY OR

IN PART UPON ANY DESCRIPTION, PHOTOGRAPH

OR STATEMENT CONTAINED HEREIN. COLORS AND

SPECIFICATIONS MAY VARY FROM ACTUAL PRODUCT.

MUSIC GROUP PRODUCTS ARE SOLD THROUGH

AUTHORIZED FULLFILLERS AND RESELLERS ONLY.

FULLFILLERSAND RESELLERS ARE NOT AGENTS OF

MUSICGROUP AND HAVE ABSOLUTELY NO AUTHORITY

TO BIND MUSICGROUP BY ANY EXPRESS OR IMPLIED

UNDERTAKING OR REPRESENTATION. THIS MANUAL

IS COPYRIGHTED. NO PART OF THIS MANUAL MAY

BE REPRODUCED OR TRANSMITTED IN ANY FORM

OR BY ANY MEANS, ELECTRONIC OR MECHANICAL,

INCLUDING PHOTOCOPYING AND RECORDING OF ANY

KIND, FOR ANY PURPOSE, WITHOUT THE EXPRESS

WRITTEN PERMISSION OF MUSICGROUPIPLTD.

Trident Chambers, Wickhams Cay, P.O. Box 146,

Road Town, Tortola, British Virgin Islands

For the applicable warranty terms and conditions

and additional information regarding MUSIC Group’s

Limited Warranty, please see complete details online at

www.music-group.com/warranty.

4 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

1. Before you get Started

1.1 Shipment

Your PMP mixer was carefully packed at the factory and the packaging is

designed to protect the unit from rough handling. Nevertheless, we recommend

that you carefully examine the packaging and its contents for any signs of

physical damage which may have occurred during transit.

◊ If the unit is damaged, please do NOT return it to BEHRINGER,

but notify your dealer and the shipping company immediately.

Otherwise, claims for damage or replacement may not be granted.

◊ We recommend that you use a flight case, so as to give your power

mixer optimum protection during use or transport.

◊ Always use the original packing carton to prevent damage during

storage or transport.

◊ Make sure that children cannot play unsupervised with the device or

its packaging.

◊ Please ensure proper disposal of all packing materials.

1.2 Initial operation

Be sure that there is enough air space around the unit for cooling and, to avoid

overheating, please do not place the EUROPOWER near radiators, etc.

◊ Blown fuses must be replaced by fuses of the same type and rating!

Please refer to the “Specifications” for details.

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certication requirements.

◊ Please make sure that all units have proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or on the AC power cord.

◊ Important notes concerning installation: The sound quality may

diminish within the range of powerful broadcasting stations and

high-frequency sources. Increase the distance between the transmitter

and the device and use shielded cables for all connections.

1.3 Online registration

Please register your new BEHRINGER equipment right after your purchase

by visiting http://behringer.com and read the terms and conditions of our

warrantycarefully.

Should your BEHRINGER product malfunction, it is our intention to have it

repaired as quickly as possible. To arrange for warranty service, please contact

the BEHRINGER retailer from whom the equipment was purchased. Shouldyour

BEHRINGER dealer not be located in your vicinity, you may directly contact

one of our subsidiaries. Corresponding contact information is included in the

original equipment packaging (Global Contact Information/European Contact

Information). Should your country not be listed, please contact the distributor

nearest you. A list of distributors can be found in the support area of our website

(http://behringer.com).

Registering your purchase and equipment with us helps us process your repair

claims more quickly and eciently.

Thank you for your cooperation!

1.4 The manual

This manual is designed to give you both an overview of all control elements and

to provide detail about how to use them. To provide you with a clear structure,

we have grouped the control elements according to their function. They can

easily be found on the enclosed numbered illustrations. If you need more

detailed information on specic topics, please visit our web site behringer.com.

The product-related information pages and the Ultranet-based glossary explain

the relevant audio engineering terminology in full detail.

5 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

(34)

(32)

(36)

(1)

(2)

(3)

(4)

(5)

(6)

(8)

(14)

(16) (21) (20) (19) (24)

(23)

(28)

(29)

(30)

(26)(25)(22)(20)(21)

(15)

(18)

(17)

(27)

(31)

(13)

(12)

(10)

(11)

(9)

(12)

(40)

(33) (35) (37) (39)(38)

(1)

(2)

(3)

(4)

(5)

(7)

(8)

Front Panel

Rear Panel

(41)

(42)

(44) (43)

(45)

6 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

2. Control Elements

A detailed description of all functions of your power mixer can be found in the

following chapters. Please also refer to the enclosed sheet with the numbered

illustrations to get an overview of the control layout.

2.1 Mono and stereo channels

(1) The HIGH control in the EQ section governs the high-frequency range of the

respective channel.

(2) Use the MID control to boost or cut the mid-range frequencies.

(3) The LOW control allows you too boost/cut the low-frequency range.

(4) With the MON control you can adjust the volume of each channel in the

monitor mix.

(5) The FX control determines the signal level sent from each channel to the

built-in eects processor; this signal is also present at the FX OUT jack

(see (32) ). The PMP980S/PMP1680S has two FX controls (FX 1 and FX 2),

sothat you can use two eects simulteneously. Accordingly, it also provides

two eect Aux paths (see (32)).

◊ Please note that the effects processor signal will be inaudible when the

FX RETURN control (21) is set fully counter-clockwise.

(6) For the mono input channels, the PMP980S/PMP1680S has a PAN(ORAMA)

control which determines the position of the channel signal in the stereo

main mix. The PMP960M has no PAN on the input channels, because it is a

dual-mono power mixer.

(7) The BAL(ANCE) control for the stereo channels of the PMP980S/PMP1680S

corresonds to the PAN control for the mono channels. It determines the

relative volume of the left and right input signals before they are routed to

the stereo main output. The PMP960M has no stereo channels and hence no

BAL control, because it is a dual-mono power mixer.

(8) The LEVEL control adjusts the channel signal level in the main mix.

2.1.1 Input section

(9) The CLIP LED is very useful to control the input gain. It should never be

constantly illuminated (only with signal peaks).

(10) The PAD switch reduces the input sensitivity of the channel by

approx.30dB,to connect for example line-level signals.

(11) The balanced HI-Z input (¼" TRS) can be used for line-level signal sources,

e.g. keyboards, electric guitars and basses.

(12) Each channel has a balanced LOW-Z microphone input with XLR connectors,

which also supply the +48 V phantom power for condenser microphones

(see (27) ).

(13) Unbalanced stereo line inputs with ¼" connectors for stereo channels 7 to 10

of the PMP980S/PMP1680S. They can be used for connecting keyboards with

stereo outputs or stereo drum machines.

◊ Please remember to use either the microphone or the line input of a

channel at a time, but never both at the same time!

2.2 Eects section

(14) List of all multi-eects presets.

(15) LED level meter of the eects processor. Since the PMP980S/PMP1680S

allows you to select two eects simultaneously, it also has two level meters

(DUAL FX). Be sure that the clip LED illuminates for signal peaks only. If it is

illuminated all the time, it is a sign that the eects processor is overloading

and hence producing unpleasant distortion.

(16) The Eect display (PMP980S/PMP1680S: two displays) shows the currently

selected preset.

(17) Turn the PROGRAM control (PMP980S/PMP1680S: one control each for

FX1and FX 2) to select an eects preset (preset number starts ashing).

Push the control briey to conrm your selection.

(18) Press the FX IN button (PMP980S/PMP1680S: FX 1 IN and FX 2 IN) to activate

the eects processor.

2.3 Main and monitor section

(19) Your power mixer is equipped with two graphic 7-band equalizers. Theupper

one processes the monitor signal, the lower one the main signal. Use the EQs

to adjust the sound to the room acoustics.

(20) Press the FBQ IN switch to activate the FBQ Feedback Detection System.

The frequencies causing feedback are shown by the brightly lit fader LEDs.

Simply lower the level of the respective frequency range until feedback

disappears and the LED goes out. Your power mixer oers this function both

for the main and the monitor mix.

(21) Turn the FX RET control to add the eect signal to the main mix (lower)

ormonitor mix (upper). The PMP980S/PMP1680S allows you to use two

eects at the same time, it also has two FX controls each for the main

and monitor mixes: when the FX RET 1 and FX RET 2 controls are fully

counterclockwise, no eect signal is added.

(22) The CD/TAPE IN control adjusts the volume of the 2 Track In signal (see (35)).

(23) The MONITOR MASTER control adjusts the monitor output volume.

(24) Use this 5-digit LED meter to control the output level of the monitor signal.

The upper LIM LED illuminates when the internal amp protection circuit

responds to output levels that are too high.

(25) The MAIN MASTER control is used to adjust the main output volume.

(26) Use this 5-digit LED meter to control the output level of the main signal.

ThePMP980S/PMP1680S has two rows of LED meters (L/R), because the

signal is stereo. The upper LIM LED illuminates when the internal amp

protection circuit responds to output levels that are too high.

(27) +48 V phantom power is provided for condenser microphones. The phantom

power supply is activated for all channels with the PHANTOM switch and the

PHANTOM LED above the switch illuminates.

(28) Use the POWER AMP switch to determine the operating mode of your

powermixer.

The PMP980S/PMP1680S has three dierent operating modes:

InMAINL/MAIN R mode it functions as a stereo amplier, i.e. the left

and right main stereo signals are sent to OUTPUT A (L) and OUTPUT B (R).

InMON/MONO mode it functions as a dual mono amplier, i. e. OUTPUT A

sends the monitor signal, and OUTPUT B the main signal (mono). In BRIDGE

AMP MODE the output power of outputs A and B are added and provided

atOUTPUT B.

The PMP960M also has three operating modes, since it can be

operated in two modes with the switch in its upper position

(MAIN/MAIN(BRIDGE)mode), depending on the pin connections of the

speaker cables. In MAIN/MAIN (BRIDGE) mode power of both outputs is

added and provided at OUTPUT B (Locking cable, pins 1+/2+). Withthe

normal pin connections (Locking cable, pins 1+/1-) a main signal is provided

in this mode at OUTPUT A and B (not bridged). In MON/MAIN mode,

themixer can also be used as a dual mono amplier, i.e. OUTPUT A provides

the monitor signal, while the main signal is present at OUTPUT B.

Please refer to (44) and (45) as well as chapter 4.4 “Loudspeaker connectors”.

7 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

◊ In BRIDGE mode, always connect only one loudspeaker with

an impedance of at least 8 Ω to OUTPUT B (pins 1+/2+)!

Please note that OUTPUT A must NEVER be used in BRIDGE mode

(with pin connections 1+/2+)!

◊ In all other operating modes, the minimum impedance of the speaker

connected must not fall below 4 Ω.

(29) Use the SPEAKER PROCESSING switch to activate a lter that adapts

the mixer to the specications of your loudspeakers. If the speakers have

a limited frequency response in the bass range, it allows you to adapt it

optimally to the frequency response of the speakers.

(30) If STANDBY is pressed, all input channels are muted. During breaks you

can thus prevent the microphones from picking up noise or interference,

which would then be reproduced by the P.A. system. The advantage is that

all faders can be left untouched while you play a CD via the CD/TAPE inputs

(see(35) ). There is also no need to move down the faders of muted channels

and lose your mix.

2.3.1 Connectors

(31) The FOOTSWITCH connector is for a standard footswitch. You can activate

an “eect bypass” that mutes the eects processor. Please use a dual

footswitch for the PMP980S/PMP1680S, so that you can enable/disable FX1

and FX 2 independently of each other. In this case, the tip of the ¼" plug

controls FX 1, and the ring FX 2.

(32) The FX OUT connector is used to route the FX SEND signal from the input

channels, for example, to the input of an external eects processor.

ThePMP980S/PMP1680S has two FX controls per input signal (see (5) )

andalso two FX OUT connectors (FX OUT 1 and FX OUT 2).

◊ Please note: When you connect a mono plug to one of the FX OUT jacks,

the signal path from the respective FX send to the built-in effects

processor is interrupted. For each FX send you can either use the

built-in effect or the corresponding FX OUT jack (for an external effect),

but never both at the same time. When you use a stereo plug (tip and

ring interconnected) you can use the built-in effects processor and the

FX OUT jacks in parallel.

(33) Use the AUX IN ¼" inputs to route an external stereo signal to the main mix.

This can be the signal generated by an external eects processor. Use the

left input for mono signals, which are then reproduced on both stereo sides.

ThePMP960M has only one mono AUX IN connector.

(34)

The AUX IN control adjusts the volume of the external signal in the main mix.

(35) The CD/TAPE IN RCA input allows you to feed in external stereo signals,

e.g.from a CD player, tape deck or other line-level source.

(36) The VOICE CANCELLER lters vocal-specic frequencies from the CD/TAPE IN

signal. This function can be used for karaoke, i.e. you can remove the vocals

from a song and then sing along with the music yourself.

(37) The REC OUT (RCA) provides line-level signals from the power mixer to a

DAT recorder, for example. On the PMP980S/PMP1680S the REC OUT signal is

stereo and on the PMP960M two identical mono signals are provided.

◊ If the REC OUT signal is connected to a recorder whose output signal

is returned to the CD/TAPE IN, feedback can occur when you activate

the record function. So, disconnect the CD/TAPE IN from the recorder,

before you start recording!

(38) The MAIN ¼" connectors allow you to send the main signal to an external

amplier, when you only wish to use the mixer and eects section.

Thesignal is taken pre-power stage of the mixer. It is also possible to

use only the left jack of the output. The PMP960M has only one mono

outputconnector.

(39) Connect your monitor power amps or active monitor speakers to the mono

MONITOR output to monitor the signal mix created with the MON controls

or to route it to the musicians on stage.

(40) Use the POWER switch to put the unit into operation. The POWER switch

should always be in the “O” position when you are about to connect the

unit to the mains.

◊ Please note: The POWER switch does not fully disconnect the unit from

the mains. Unplug the power cord completely when the unit is not used

for prolonged periods of time.

2.4 Rear panel

(41) The mains connection is on a standard IEC receptacle. An appropriate power

cord is supplied with the unit.

(42) FUSE HOLDER. Before connecting the unit to the mains, ensure that

the voltage setting matches your local voltage. Blown fuses should only

be replaced by fuses of the same type and rating. Please also read the

information given in chapter 6 “Specications”.

(43) Loudspeaker OUTPUT A.

PMP980S/PMP1680S: Depending on the operating mode selected (see (28) )

either the left main signal or the monitor signal is provided at OUTPUT A.

Never use this output in bridged mono mode.

PMP960M: In MON/MAIN mode, the monitor signal is provided at

OUTPUTA (see (28) ). Never use this output in bridged mono mode,

exceptwhen you use a cable with the normal pin connections (pins1+/1-).

In this case you can take the mono main signal from this output in

MAIN/MAIN (BRIDGE) mode (not bridged). Please also refer to chapter 4.3

“Loudspeakerconnection”.

◊ The impedance of the loudspeaker connected must not fall below 4 Ω.

◊ Please note that the power delivered to the speaker in bridged

mono mode is considerably higher than in other operating modes.

Please read the information given on the rear panel of the power mixer.

(44) Loudspeaker OUTPUT B.

PMP980S/PMP1680S: Depending on the operating mode selected (see (28) )

either the right main signal, the mono main signal or the bridged mono

signal is provided at OUTPUT B.

PMP960M: Either the main or the bridged main mono signal is provided at

OUTPUT B (see (28) ). When you use a cable with the normal pin connections

(pins 1+/1-), it is possible in MAIN/MAIN (BRIDGE) mode to take the mono

main signal from this output (not bridged). Please also refer to chapter 4.3

“Loudspeaker connection”.

◊ In BRIDGE mode, always connect only one loudspeaker with an

impedance of at least 8 Ω to OUTPUT B (pins 1+/2+)! Please note

that OUTPUT A must NEVER be used in BRIDGE mode (with pin

connections 1+/2+)!

◊ In all other operating modes, the minimum impedance of the speaker

connected must not fall below 4 Ω.

◊ Information on how to properly connect your speaker with regard to

polarity can be found on the rear of the mixer (PINOUTs).

(45) SERIAL NUMBER.

8 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

3. Digital Eects Processor

24-BIT MULTI-EFFECTS PROCESSOR

This built-in eects module produces high-grade standard eects such as

reverb, chorus, anger, delay and various combination eects. The integrated

eects module has the advantage of requiring no wiring. This way, the danger

of creating ground loops or uneven signal levels is eliminated at the outset,

completely simplifying the handling.

These eect presets are designed to be added to dry signals. If you move the

FXRET control, you mix the channel signal (dry) and the eect signal.

◊ Turn down the FX controls in those channel strips whose signals you

don’t wish to process.

4. Installation

4.1 Mains connection

Blown fuses must be replaced by fuses of the same type and rating.

The mains connection is made using the enclosed power cord and a standard IEC

receptacle. It meets all of the international safety certication requirements.

◊ Please make sure that all units have a proper ground connection.

For your own safety, never remove or disable the ground conductor

from the unit or of the AC power cord.

4.2 Audio connections

The inputs and outputs of the BEHRINGER EUROPOWER are unbalanced ¼" TS

connectors—except for the balanced mono line inputs. Of course, all inputs and

outputs work with both balanced and unbalanced connectors. The Tape Ins and

Outs are on stereo RCA connectors.

◊ Please ensure that only qualified personnel install and operate the

power mixer. During installation and operation, the user must have

sufficient electrical contact to earth. Electrostatic charges might affect

the operation of the unit.

Fig. 4.1: ¼" TS connector

strain relief clamp

sleeve

tip

sleeve

(ground/shield)

Unbalanced ¼" TS connector

tip

(signal)

Fig. 4.2: ¼" TRS connector

strain relief clamp

sleeve

ring

tip

sleeve

ground/shield

For connection of balanced and unbalanced plugs,

ring and sleeve have to be bridged at the stereo plug.

Balanced ¼" TRS connector

ring

cold (-ve)

tip

hot (+ve)

Fig. 4.3: XLR connectors

output

For unbalanced use, pin 1 and pin 3

have to be bridged

1 = ground/shield

2 = hot (+ve)

3 = cold (-ve)

input

Balanced use with XLR connectors

Fig. 4.4: ¼" TS connector for footswitch

strain relief clamp

sleeve

tip

sleeve

pole 1/ground

tip

pole 2

The footswitch connects both poles momentarily

¼" TS footswitch connector

9 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

◊ Please use a dual footswitch for the PMP980S/PMP1680S, so that you

can enable/disable FX 1 and FX 2 independently of each other. In this

case, the tip of the ¼" plug controls FX 1, and the ring FX 2.

Fig. 4.5: RCA cable

shield

sleevesleeve

tip tip

4.3 Loudspeaker connection

Your PMP mixer is equipped with high-quality twist-lock professional style

loudspeaker connectors, which ensure safe and trouble-free operation.

Thisconnector was especially developed for high-power loudspeakers. Once it is

plugged in, it safely locks into position and cannot be accidentally disengaged.

Itprevents the occurrence of electrical shock and ensures the correct polarity.

Each of the connectors carries only the assigned single signal (see tab. 4.1/g. 4.7

and the information on the rear panel of the power mixer).

Fig. 4.6: Professional twist-lock style connector

front view rear view

Professional speaker connector

(compatible with Neutrik Speakon connectors)

Please be sure to only use professional locking-style speaker cables (type NL4FC).

Please check the pin connections of your loudspeakers and cables depending on

the EUROPOWER speaker output you choose.

EUROPOWER PMP980S/PMP1680S

OUPUT A 1+ 1- 2+ 2-

MAIN L POS NEG – –

MON POS NEG – –

OUTPUT B – – POS NEG

OUTPUT B 1+ 1- 2+ 2-

MAIN R POS NEG – –

MONO POS NEG – –

BRIDGE POS – NEG –

EUROPOWER PMP960M

OUTPUT A 1+ 1- 2+ 2-

MAIN MONO POS NEG – –

MON POS NEG – –

BRIDGE – – – –

OUTPUT B 1+ 1- 2+ 2-

MAIN MONO POS NEG – –

MAIN POS NEG – –

BRIDGE POS – NEG –

Tab 4.1: Pin connections of loudspeaker connectors

OUTPUT B

BRIDGE

1- 1-

8 Ω

4 Ω

8 Ω

4 Ω

16 Ω

8 Ω

OUTPUT B

Fig. 4.7: Connector assignment

10 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

5. Wiring Examples

For stereo operation the POWER AMP switch (28) of the PMP980S/PMP1680S

must be set to its upper position (MAIN L/MAIN R). Outputs A and B deliver

the stereo main signal to the P.A. speakers. Two active speakers, wired in

parallel, are connected to the preamp monitor output. They are used as

on-stage monitor speakers. The eects processors can be switched on and

o with a dual footswitch. This set-up is not possible with the PMP960M

(nostereooperationpossible).

Loudspeaker (F.O.H. mix)

PMP1680S

2 x BEHRINGER EUROLIVE

Stack (B1800X & B1220, both passive)

Loudspeaker connection (monitor mix)

2 x BEHRINGER B215A (active)

PMP1680S Front Panel

(excerpt)

Dual footswitch

Fig. 5.1: EUROPOWER mixer as a stereo amplier (example)

Both the PMP980S/PMP1680S and the PMP960M can be set-up for dual mono

operations. The POWER AMP switch (28) must be set to its lower (PMP960M)

orcenter position (PMP980S/PMP1680S). The two loudspeaker outputs

provide the main and monitor signals independently of each other and to two

loudspeakers each, which are wired in parallel.

Loudspeaker connection for F.O.H and

monitor mix (mono)

PMP960M Rear Panel

(excerpt)

2 x BEHRINGER

EUROLIVE F1520

(passive)

2 x BEHRINGER EUROLIVE B1520

(passive)

Fig. 5.2: EUROPOWER as a dual mono amplier (example)

11 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

This illustration shows just one example of how the channels of your power mixer

can be used, including the connection of mono and stereo sources, and the tape

ins and outs recording the mix signal or playing back external signals.

EUROPOWER PMP1680S

Stereo channel 7/8

Dat recorder

Electric

guitar

V-AMP2

Keyboard

Vocal mics

Electric

bass

DI box

Mono

channel 5

Mono

channels 1-4

Mono

channel 6

Tape In/Out

Fig. 5.3: Standard set-up (example)

One example of how to use your power mixer with a subwoofer in bridged mono

mode. The illustration shows the PMP1680S with a subwoofer connected to

OUTPUT B that will receive the full (bridged) output power. A separate stereo

power amp (BEHRINGER EUROPOWER EP2000) for the stereo main P.A. signal is

connected to the Pre Amp Main outputs. The Pre Amp monitor output is wired

to active speakers on the stage. This application can also be realized with the

PMP960M, except for the main P.A. signal, which would be mono.

Subwoofer

EUROLIVE

B1220 PRO

EUROLIVE

B1800X PRO Subwoofer

2 x BEHRINGER B215A

(active)

F.O.H. mix Monitor mix

EUROPOWER EP1500

Fig. 5.4: EUROPOWER in bridged mono mode

12 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

6. Specications

Microphone Inputs

Type XLR, electronically balanced input circuit

Mic E.I.N. (20 Hz - 20 kHz)

@ 0 Ohm source resistance -112 dB / 114 dB A-weighted

@ 50 Ohm source resistance -112 dB / 114 dB A-weighted

@ 150 Ohm source resistance -112 dB / 114 dB A-weighted

Frequency response < 10 Hz - 200 kHz (-1 dB)

< 10 Hz - > 200 kHz (-3 dB)

Gain +30 dB, +10 dB with pad

Max. input level +12 dBu @ +10 dB gain

Impedance approx. 2.2 kOhm balanced /

approx. 1.1 kOhm unbalanced

Signal-to-noise ratio 110 dB / 114 dB A-weighted

(0 dBu In @ +10 dB gain)

Noise (THD + N) 0.001% / 0.0007% A-weighted

Mono Line Inputs

Type ¼" TS connectors, balanced

Impedance approx. 20 kOhm, balanced

Max. input level +21 dBu

Stereo Line Inputs

PMP980S/PMP1680S

Type ¼" TRS connectors, unbalanced

Impedance approx. 100 kOhm, unbalanced

Max. input level +21 dBu

Equalizer

Low 80 Hz / +/-15 dB

Mid 2.5 kHz / +/-15 dB

High 12 kHz / +/-15 dB

CD/TAPE Input

Type RCA

Impedance approx. 10 kOhm

Preamp Outputs

MAIN

Type ¼" TS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

MONITOR

Type ¼" TS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. output level +21 dBu

Stereo Outputs

PMP960M

Type RCA, mono output

Impedance approx. 1 kOhm

Max. input level +21 dBu

PMP980S/PMP1680S

Type ¼" TRS connectors, unbalanced

Impedance approx. 150 Ohm, unbalanced

Max. input level +21 dBu

Type RCA

Impedance approx. 1 kOhm

Max. input level +21 dBu

Main Mix System Data

Noise:

MAIN MIX @ -∞ -102 dB/-106 dB A-weighted

Channel fader -∞

MAIN MIX @ 0 dB -88 dB/-91 dB A-weighted

Channel fader -∞

MAIN MIX @ 0 dB -84 dB/-86 dB A-weighted

Channel fader @ 0 dB

Loudspeaker Outputs

Type Neutrik Speakon-compatible connector

Load impedance:

MAIN L/R 4 - 8 Ohm

MONITOR/MAIN MONO 4 - 8 Ohm

MAIN MONO/MAIN MONO 4 - 8 Ohm

BRIDGE 8 - 16 Ohm

13 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

DSP

Converter 24-bit Delta-Sigma,

64/128-times oversampling

Dynamics D/A 90 dB

Sampling rate 40 kHz

Delay Time max. 5 secs

Signal run time approx. 1.5 ms

(Line In > Line Out)

Display

PMP960M

Type 2-digit, 7-segment LED

PMP980S/PMP1680S

Type 2 x 2-digit, 7-segment LED

Output Power

PMP960M/PMP980S

RMS @ 1% THD (sine wave), both channels driven:

8 Ohm per channel 160 W

4 Ohm per channel 300 W

RMS @ 1% THD (sine wave), bridged mode:

8 Ohm 600 W

Peak Power, both channels driven:

8 Ohm per channel 260 W

4 Ohm per channel 450 W

Peak Power, bridged mode:

8 Ohm 900 W

PMP1680S

RMS @ 1% THD (sine wave), both channels driven:

8 Ohm per channel 300 W

4 Ohm per channel 600 W

RMS @ 1% THD (sine wave), bridged mode:

8 Ohm 1200 W

Peak Power, both channels driven:

8 Ohm per channel 400 W

4 Ohm per channel 800 W

Peak Power, bridged mode:

8 Ohm 1600 W

Fuses

PMP1680S

100 - 120 V~, 50/60 Hz T 10 A H 250 V

220 - 240 V~, 50/60 Hz T 6.3 A H 250 V

Power Consumption

Power consumption 1000 W

Mains connector IEC standard receptacle

Dimensions/Weight

Dimensions (H x W x D) approx. 315 x 460 x 220 mm

(approx. 12 / x 18 / x 8 /")

PMP960M

Weight 8.5 kg (18 / lbs)

PMP980S

Weight 9.4 kg (20 / lbs)

PMP1680S

Weight 9.9 kg (21 / lbs)

BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts,

modifications may be made from time to time to existing productswithout prior notice. Specifications and

appearance may differ from those listed or illustrated.

14 EUROPOWER PMP1680S/PMP980S/PMP960M User Manual

FEDERAL COMMUNICATIONS

COMMISSION COMPLIANCE

INFORMATION

Responsible Party Name: MUSIC Group Services US Inc.

Address: 18912 North Creek Parkway,

Suite 200 Bothell, WA 98011,

USA

Phone Number: +1 425 672 0816

EUROPOWER PMP1680S/PMP980S/PMP960M

complies with the FCC rules as mentioned in the followingparagraph:

This equipment has been tested and found to comply with the limits for a ClassB

digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment o and on, the user is encouraged to try to correct the

interference by one or more of the followingmeasures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician forhelp.

This device complies with Part 15 of the FCC rules. Operation is subject to the

following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may

cause undesired operation.

Important information:

Changes or modications to the equipment not expressly approved by MUSIC Group

can void the user’s authority to use the equipment.

EUROPOWER

PMP1680S/PMP980S/PMP960M

We Hear You

Behringer Europower PMP1680S User manual

Brand: Behringer

Model: Europower PMP1680S

Category: Mixers

Type: User manual

This manual is also suitable for

Download PDF

report

Behringer Europower PMP1680S User manual

This manual is also suitable for

Behringer Europower PMP1680S User manual

Related papers

Other documents