Klark Teknik DI 10P Quick start guide

Category
Musical Equipment
Type
Quick start guide

Klark Teknik DI 10P is a passive DI box designed to convert unbalanced stereo or mono signals to a balanced XLR output for connection to mixing consoles or other professional audio equipment. It features stereo RCA and 1/8-inch TRS inputs, allowing for a variety of sources, and a summed mono output via XLR. The input levels can be adjusted individually, and an Earth Lift switch helps reduce unwanted hum. With a wide frequency response, low distortion, and high signal-to-noise ratio, the DI 10P ensures transparent audio reproduction.

Klark Teknik DI 10P is a passive DI box designed to convert unbalanced stereo or mono signals to a balanced XLR output for connection to mixing consoles or other professional audio equipment. It features stereo RCA and 1/8-inch TRS inputs, allowing for a variety of sources, and a summed mono output via XLR. The input levels can be adjusted individually, and an Earth Lift switch helps reduce unwanted hum. With a wide frequency response, low distortion, and high signal-to-noise ratio, the DI 10P ensures transparent audio reproduction.

PRO DI 10P
Passive DI Box with Stereo Input / Summed Mono Output,
MIDAS Transformer and Extended Dynamic Range
INPUTS – Connect your source audio via stereo RCA jacks or a single ⁄" TRS jack. The unused input jack can act as a loop-through output. A mono source can also be connected to one
of the RCA jacks, or to the ⁄" input.
LEVEL L/R – The level of the left and right channels can be adjusted before being sent to the output jack. Normally these knobs should be set fully clockwise, but may be used to
attenuate very hot signals, or to correct the balance between the channels.
OUTPUT – Send the summed inputs to a mixing console via balanced XLR cable. The output level is approximately 20 dB lower than the input signal.
EARTH LIFT – This switch may help reduce unwanted hum by removing the ground connection.
Speci cations
Inputs
Connectors RCA unbalanced, ⁄ TRS
Impedance 7 k
Outputs
Connector XLR , balanced
Impedance 170 
System
Frequency response 10 Hz to 91 kHz (± 1 dB)
THD + N (distortion) <0.03% @ 1 kHz, +4 dBu
Signal-to-noise ratio >120 dB @ 1 kHz, +4 dBu
Power requirement Passive
Physical
Dimensions (WxDxH) 64 x 118 x 112 mm
(2.5 x 4.7 x 4.4")
Weight 0.47 kg (1.0 lbs)
klarkteknik.com
LEGAL DISCLAIMER
MUSIC Group accepts no liability for any loss which may be su ered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein.
Technical speci cations, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. MIDAS, KLARK TEKNIK,
LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, and BUGERA are trademarks or registered trademarks of MUSIC Group IP Ltd.
© MUSIC Group IP Ltd. 2017 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information regarding MUSIC Group’s Limited Warranty, please see complete details online at
music-group.com/warranty.
  • Page 1 1

Klark Teknik DI 10P Quick start guide

Category
Musical Equipment
Type
Quick start guide

Klark Teknik DI 10P is a passive DI box designed to convert unbalanced stereo or mono signals to a balanced XLR output for connection to mixing consoles or other professional audio equipment. It features stereo RCA and 1/8-inch TRS inputs, allowing for a variety of sources, and a summed mono output via XLR. The input levels can be adjusted individually, and an Earth Lift switch helps reduce unwanted hum. With a wide frequency response, low distortion, and high signal-to-noise ratio, the DI 10P ensures transparent audio reproduction.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI