Alto DRAGONFLY A1000.4 Owner's manual

Brand: Alto

Model: DRAGONFLY A1000.4

Category: Audio amplifiers

Type: Owner's manual

A1000.4 DRAGONFLY

HIGH EFFICIENCY DIGITAL AMPLIFIER

OWNER'S MANUAL

www.altoproaudio.com

Version 1.2 OCT. 2007

LTO

English

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

IMPORTANT SAFETY INSTRUCTION

TO REDUCE THE RISK OF ELECTRIC SHOCK

PLEASE DO NOT REMOVE THE COVER OR

THE BACK PANEL OF THIS EQUIPMENT.

THERE ARE NO PARTS NEEDED BY USER

INSIDE THE EQUIPMENT. FOR SERVICE,

PLEASE CONTACT QUALIFIED SERVICE

CENTERS.

WARNING

To reduce the risk of electric shock

and fire, do not expose this equipment

to moisture or rain.

10.

Dispose of this product should

notbeplacedinmunicipalwaste

and should be separate collection.

11.

12.

MovethisEquipmentonlywithacart,

stand, tripod, or bracket,

specified by the

manufacturer, or

sold with the

Equipment. When

a cart is used, use

caution when

moving the cart /

equipment

combination to

avoid possible

injury from tip-over.

Permanent hearing loss may be caused by

exposure to \ extremely high noise levels.

The US. Government's Occupational Safety

and Health Administration (OSHA) has

specified the permissible exposure to noise

level.

These are shown in the following chart:

According to OSHA, an exposure to high SPL in

excess of these limits may result in the loss of

heat. To avoid the potential damage of heat, it is

recommended that Personnel exposed to

equipment capable of generating high SPL use

hearing protection while such equipment is

under operation.

This symbol, wherever used, alerts you to the

presence of un-insulated and dangerous voltages

within the product enclosure. These are voltages that

may be sufficient to constitute the risk of electric

shock or death.

This symbol, wherever used, alerts you to

important operating and maintenance instructions.

Please read.

Protective Ground Terminal

AC mains (Alternating Current)

Hazardous Live Terminal

ON: Denotes the product is turned on.

OFF: Denotes the product is turned off.

The apparatus shall be connected to a mains

socket outlet with a protective earthing

connection.

The mains plug or an appliance coupler is used

as the disconnect device, the disconnect device

shall remain readily operable.

CAUTION

Describes precautions that should be observed to

prevent damage to the product.

Read this Manual carefully before operation.

Keep this Manual in a safe place.

Be aware of all warnings reported

with this symbol.

Keep this Equipment away from water and

moisture.

Clean it only with dry cloth. Do not use

solvent or other chemicals.

Do not damp or cover any cooling opening.

Install the equipment only in accordance with

the Manufacturer's instructions.

Power Cords are designed for your safety. Do

not remove Ground connections! If the plug

does not fit your AC outlet, seek advice from

a qualified electrician. Protect the power

cord and plug from any physical stress to

avoid risk of electric shock. Do not place

heavy objects on the power cord. This could

cause electric shock or fire.

Unplug this equipment when unused for long

periods of time or during a storm.

Refer all service to qualified service personnel

only. Do not perform any servicing other than

those instructions contained within the

User's Manual.

To prevent fire and damage to the product,

use only the recommended fuse type as

indicated in this manual. Do not short-circuit

the fuse holder. Before replacing the fuse,

make sure that the product is OFF and

disconnected from the AC outlet.

HOURS X DAY

EXAMPLE

1,5

0,5

0,25 or less

SPL

100

102

105

110

115

Small gig

train

Subway train

High level desktop monitors

Classic music concert

Rock concert

1. INTRODUCTION

Thank you for your purchasing of the LTO A1000.4 Dragonfly digital stereo

amplifier. It is just one of the many LTO products that a talented,

multinational Team of Audio Engineers and Musicians have developed with

their great passion for music. Your A1000.4 is based on an advanced digital

amplifier circuit and Switch Mode Power Supply.

It is capable of 250 watt of power and it is possibly the smallest and lightest

amplifier in the world with such power. Yet, it is only 1 rack space and 1.5U

in height for a total of 6.8 Kg!

Due to the amplifier efficiency of over 90% there is no need for a cooling

fan and therefore your A1000.4 is perfectly suitable for Studio Application

as well as for amplification of compression drivers or full range speakers

where a very high SPL is not demanded.

Enjoy your A1000.4 and make sure to read this Manual carefully before

operation!

2. FEATURES

Mountable in a 19" rack unit (1.5U) and 1 rack space,

Digital stereo amplifier

Hi-fi quality for Studio applications

Solid and durable, rack-mountable configuration

Switchable Clip-Limiter.

4 250 Watts continuous EIAJ on 4 Ohm

4 450 Watts dynamic power on 4 Ohm

4 COMBO input sockets compatible with balanced XLR and Neutrik

Speak-on connectors for outputs.

Front panel LED indicators for Clipping, Limiter, Power ON and Signal

Individual Channel level control

Manufactured under QS9000, VDA6.1 certified management system

IN THIS MANUAL:

1. 1

2. FEATURES.....................................................................................1

3. CONTROL ELEMENTS...................................................................4

4. OPERATION...................................................................................6

5. TECHNICAL SPECIFICATIONS.........................................................8

6. WARRANTY...................................................................................9

INTRODUCTION..............................................................................

Also in this case, A1000.4 is connected to the CTRL ROOM output of the mixer

and drives passive studio monitors such as the There is plenty

of power even for bigger monitors still maintaining a very good headroom.

four .

LTO MICRO4

RECORDING STUDIO SET UP

HOOK

CLIP

SIG

LIMIT

CH1

POWER

OFF

CLIP

SIG

LIMIT

CH1

POWER ON

CLIP

SIG

LIMIT

CH2

CLIP

SIG

LIMIT

CH3

CLIP

SIG

LIMIT

CH4

A1000.4

DRAGONFLY

LTO

Today the advent of high-quality computer generated music creates the need

for hi-fi quality and high SPL audio reproduction. In this example, the A1000.4

is connected to the output of your computer sound card and drives two pairs

of advanced multimedia speakers such as the

LTO MICRO4.

MULTIMEDIA SET UP

HOOK

CLIP

SIG

LIMIT

CH1

POWER

OFF

CLIP

SIG

LIMIT

CH1

POWER ON

CLIP

SIG

LIMIT

CH2

CLIP

SIG

LIMIT

CH3

CLIP

SIG

LIMIT

CH4

A1000.4

DRAGONFLY

LTO

In this case, a passive mixer with different sound sources connected such as

microphone, keyboard and electric guitar send the main mix signal to the A1000.4.

You can connect two pairs of passive PA cabinets such as the or

for a gig in a small pub/bar or for a small Band rehearsal session.

LTO ELVIS 10

ELVIS 12

SMALL GIG SET UP

HOOK

CLIP

SIG

LIMIT

CH1

POWER

OFF

CLIP

SIG

LIMIT

CH1

POWER ON

CLIP

SIG

LIMIT

CH2

CLIP

SIG

LIMIT

CH3

CLIP

SIG

LIMIT

CH4

A1000.4

DRAGONFLY

LTO

3. CONTROL ELEMENTS

It will flash when you are reaching the maximum power output of the amplifier.

It should flash only occasionally for optimum operation.

Front Panel:

1 Power On LED

This green LED will light up when you switch the A1000.4 ON.

2 Power Switch

To switch the A1000.4 ON and OFF.

3 Level Control for Channels 1, 2,3&4

Adjust the output signal level of the respective channel.

4 Clip LED

5 Limit LED

This LED will flash when the internal limiter is operating.

The limiter will prevent distortion and will protect the life of high frequency

transducers.

6 Signal LED

When a signal is applied to the input of your A1000.4, this LED will light up.

SPOTLIGHT

POWER

OFF

POWER ON

A1000.4

DRAGONFLY

LTO

CLIP

SIG

LIMIT

CH1

CLIP

SIG

LIMIT

CH1

CLIP

SIG

LIMIT

CH2

CLIP

SIG

LIMIT

CH3

CLIP

SIG

LIMIT

CH4

CLIP

SIG

LIMIT

CH1

CLIP

SIG

LIMIT

CH1

CLIP

SIG

LIMIT

CH2

CLIP

SIG

LIMIT

CH3

CLIP

SIG

LIMIT

CH4

Rear Panel:

7 Input sockets

These sockets accept the balanced signal from XLR and 1/4" connectors as

well. These Inputs are compatible with low-impedance, unbalanced/balanced,

line-level outputs emanating from such as mixers, synthesizers, drum

machines, direct boxes, crossovers, etc. Electric guitars, microphones,

and other low level/high-impedance output devices require a pre-amp or a

D/I box. The input circuits of your A1000.4 are electronically balanced.

You can connect either symmetrical ("balanced") or unbalanced sources.

3. CONTROL ELEMENTS

SPOTLIGHT

9 LIMITER Switch

The Limiter circuit will prevent the waveforms to be flattered thus preserving

a proper dynamic range and secure signal reproduction that is distortion-

free. The Limiter status can be monitored from the limit led on the front

panel of your A1000.4.

10 AC Input

8 Output Sockets

Use these Neutrik Speak-on connectors to connect your speakers.

Standard IEC receptacle. Connect your A1000.4 an AC socket with the

supplied power cord. Before powering up your A1000.4 for the first time,

make certain the stated power requirement of the unit matches the voltage

supplied by the AC socket.

If the fuse blows, replaced with a fuse of the correct type only.

Apparaten skall anslutas till

jordat uttag nar den ansluts

till ett natverk

AC INPUT 190-240V 50Hz

FUSE:T12AL 250VAC

Power Consumotion: 900W

AC INPUT

LIMITER

OFF

CH1

CH2

LIMITER

OFF

CH3

CH4

4 SPEAKERLOAD MIN.

Use only with a 250V fuse

POWER OUTPUT

CH.4CH.3CH.1 CH.2CH.1 CH.2 CH.3 CH.4

INPUT

7 8

A DEEPER LOOK: BALANCED OR UNBALANCED?

When cables are very long (e.g., over 6 meters/20 feet), the cable itself can

act as an "antenna" and pick up radio frequency noise, AC hum, or other types

of noises. To avoid these problems, many recording studios and live sound

installers use balanced lines. The average application may not require balanced

lines, but committing balanced connectors between the mixer and your A1000.4

will cause less ground loops and hum in the system. Balanced lines carry

signals, each one out of phase with respect to the other. To be converted back

into a single, unbalanced line, both balanced lines feed a differential amplifier

input that responds to the difference in levels between signals. In this way, the

out-of-phase signals are recombined into an unbalanced signal, but interference

induced into the cable will not be out of phase. Since the difference between

these signals is zero, the differential amplifier will reject the interference

completely.

two

4. OPERATION

1. Connect two pairs of PA cabinets or studio monitors to the output of your

A1000.4. make sure that your A1000.4 is switched off and that the volume

controls are turned down all the way.

2. Connect your A1000.4 to a mixer, a preamplifier or another source making

sure that the gain and volume controls on the mixer are turned down.

3. Connect some source such as microphones, keyboards or CD player into your

Mixer or preamplifier and start to make some noise.

4. Adjust the output level of your mixer or preamplifier at a proper level. A very

low output level will generate unwanted noise.

At this point, gradually turn up the volumes in your A1000.4 making sure that

the limit LEDs only flash occasionally.

OPERATION ADVICES:

4.1 TEMPERATURE CONSIDERATION IN RACK MOUNTING:

Notice

You can mount your A1000.4 in only 1.5U with the special optional brackets.

Although your A1000.4 generates almost no heat at all, you must secure proper

ventilation inside the rack to avoid overheating.

A sustained high-temperature operation will adversely affect the sound quality,

and the amplifier may shut itself off for as long as the excessive temperature

conditions exist.

4.2 IMPEDANCE

Your A1000.4 will easily drive 4 Ohm loads in Stereo mode.

However, the impedance of any loudspeaker changes with

frequency, and its rated impedance is not always its minimum

impedance.

If you connect more than one loudspeaker to the A1000.4, please check that

the actual load impedance does not drop below the A1000.4's rated output load

that is hm. Your A1000.4 will not be damaged by excessively low output load4O

impedances, but will not be able to provide full output power and its protection

circuit will automatically cut off the output signal until the low load condition

is removed.

4.3 HOW TO CHOOSE THE CORRECT SPEAKER

Today it has become very popular to monitor and mix music

through near-field monitors "reference" speakers. With near

field monitoring, small speakers are positioned a few feet

from the engineer's ears.

As a consequence, the acoustic is not so critical. Near-field monitors offer

more advantages when compared to large studio monitor, such as smaller size

and lower cost.

Because of its optimal power rating, HI-FI performance, and a no-fan design,

your A1000.4 is ideal in driving reference near-field monitor speakers in smaller

studios.

Your A1000.4 is also at home driving high frequency compression drivers or

full range PA cabinets or Stage Monitors when enormous SPL is not required.

4.4 POWER CONSIDERATION

Digital amplifiers and switch mode power supply (which are

parts of your A1000.4) are designed to reproduce musical

signals with high dynamics, high SPL and low distortion. For

this reason, all major Manufacturers of these kinds of amplifiers do not specify

their amps in terms of RMS but most measurements are made with EIA (or

EIAJ) specifications. An EIAJ signal (you can download the signal string from

the site of Electronic Industry Association) simulates a musical signal and it is

applied to the input of LTO amplifier continuously, that is for a long period of

time. Under EIA specification, your A1000.4 will deliver 250 watt channel

continuously with 240 Volt as AC power and with one channel at a time driven.

But switch mode power supply like the one used in your A1000.4 are capable

of enormous dynamics and therefore we also measure your A1000.4 as "dynamic

power". This is the amplifier capability to deliver a very high "dynamic power" for

short periods of time securing unprecedent SPL with transient sounds. In this

case the total dynamic power of your A1000.4 is 450 watt channel on 4 Ohm.

5. TECHNICAL SPECIFICATIONS

8 Ohms per channel (EIAJ)

Dimension

150 Watt

450 Watt (PEAK POWER)

Clip: Red LED

Signal: Green LED

Frequency Response

THD

20 Hz-20 kHz+3 dB

<0.35%

A1000.4 DRAGONFLY

4 Ohms per channel (Dynamic Power)

20 Hz 20 kHz@ 0.1%THD, Stereo Mode

4 Ohms per channel (EIAJ)

250 Watt

Controls

Input Sensitivity @ 4 Ohms

+3dBu

FRONT: POWER SWITCH,

CH1 & CH2 & CH3 & CH4 LEVEL knobs

REAR: CH1 & CH2 & CH3 & CH4 LIMITER

Indicators (per channel)

Power-On: Green LED

Limit: Yellow LED

Connectors of each channel

Input: COMBO connector

Power Supply

190-240 VAC~50 Hz / 95-120 VAC~60 Hz

SNR (Signal to Noise Ratio)

76 dB

Protection

Thermal and Short Circuit Protection

Net Weight

Output: Neutrik Speak-on connector

314 x 440 x 66.6 mm

6.8 Kg

6. WARRANTY

1. WARRANTY REGISTRATION CARD

To obtain Warranty Service, the buyer should first fill out and return the enclosed

Warranty Registration Card within 10 days of the Purchase Date.

All the information presented in this Warranty Registration Card gives the

manufacturer a better understanding of the sales status, so as to provide a

more effective and efficient after-sales warranty service. Please fill out all the

information carefully and genuinely, miswriting or absence of this card will void

your warranty service.

2. RETURN NOTICE

2.1 In case of return for any warranty service, please make sure that the

product is well packed in its original shipping carton, and it can protect your

unit from any other extra damage.

2.2 Please provide a copy of your sales receipt or other proof of purchase with

the returned machine, and give detail information about your return address

and contact telephone number.

2.3 A brief description of the defect will be appreciated.

2.4 Please prepay all the costs involved in the return shipping, handling and

insurance.

3. TERMS AND CONDITIONS

3.1 warrants that this product will be free from any defects in materials

and/or workmanship for a period of 1 year from the purchase date if you

have completed the Warranty Registration Card in time.

LT O

3.2 The warranty service is only available to the original consumer, who purchased

this product directly from the retail dealer, and it can not be transferred.

3.3 During the warranty service, may repair or replace this product at its

own option at no charge to you for parts or for labor in accordance with the

right side of this limited warranty.

LT O

3.4 This warranty does not apply to the damages to this product that occurred

as the following conditions:

Instead of operating in accordance with the user's manual thoroughly, any abuse

or misuse of this product.

Normal tear and wear.

The product has been altered or modified in any way.

Damage which may have been caused either directly or indirectly by another

product / force / etc.

Abnormal service or repairing by anyone other than the qualified personnel or

technician.

And in such cases, all the expenses will be charged to the buyer.

3.5 In no event shall be liable for any incidental or consequential damages.

Some states do not allow the exclusion or limitation of incidental or

consequential damages, so the above exclusion or limitation may not apply to

you.

LT O

3.6 This warranty gives you the specific rights, and these rights are compatible

with the state laws, you may also have other statutory rights that may vary

from state to state.

NF02215-1.2

without prior notice. Any photocopy, translation, or reproduction of part of this

SEIKAKU TECHNICAL GROUP LIMITED

NO. 1, Lane 17, Sec. 2, Han Shi West Road, Taichung 40151, Taiwan

http://www.altoproaudio.com Tel: 886-4-22313737

email: [email protected] Fax: 886-4-22346757

Alto DRAGONFLY A1000.4 Owner's manual

Brand: Alto

Model: DRAGONFLY A1000.4

Category: Audio amplifiers

Type: Owner's manual

Download PDF

report

Alto DRAGONFLY A1000.4 Owner's manual

Alto DRAGONFLY A1000.4 Owner's manual

Related papers

Other documents