inVENTer GS62 Installation And Operating Instructions Manual

Installation and Operating Instructions 09/2013

GS62 Air Extractor System

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

2

LEGAL NOTICES

WARNING CONCEPT

These instructions contain information for your personal safety and to prevent material damage. Information for your

personal safety is denoted by a warning triangle. Information pertaining to material damage only has no warning

triangle. The warnings are grouped according to these levels of risk:

DANGER indicates that death or serious injury will result if proper precautions are not taken.

WARNING indicates that death or serious injury can result if proper precautions are not taken.

CAUTION with warning triangle denotes that minor injury can result if proper precautions are not

taken.

CAUTION

without warning triangle denotes that material damage can result if proper precautions

are not taken.

BEWARE denotes that an undesirable event or state can result if the relevant advisory is not heeded.

Should there be more than one level of risk, the warning for the highest level of risk is always used. A warning about

personal injury with a warning triangle may also include a warning about material damage.

NOTE denotes further, useful information.

QUALIFIED PERSONNEL

The unit/system may only be installed and operated in conjunction with this documentation. Installation, electrical

connection and initial startup of the unit/system may only be performed by qualified personnel. Qualified personnel

within the context of safety-related information in this documentation are those authorized to install, start up and

identify equipment, systems and electrical circuits in accordance with safety engineering standards.

INTENDED USE > WARNING

When installing the equipment/system, observe the applicable building codes, fire protection

regulations and accident prevention regulations of the Employer's Liability Insurance Association. Only

use the equipment/system as intended for the applications described in this documentation and only

in conjunction with the components recommended, approved and specified in this documentation

by Öko-Haustechnik inVENTer GmbH. Changes and modifications to the equipment/system are not

permitted. Trouble free and safe operation of the equipment/ system requires proper transportation,

proper storage and assembly, as well as careful operation and maintenance. This documentation is

part of the equipment/system and must be accessible at all times. Observe all safety regulations in

this documentation.

TRADEMARKS

inVENTer® is a registered trademark of ÖkoHaustechnik inVENTer GmbH. Other names used in this documentation

may be trademarks whose use by third parties may infringe upon the rights of the owner.

EXEMPTION FROM LIABILITY

The content of this documentation has been reviewed for compliance with the hardware and software described.

However, discrepancies cannot be ruled out and so liability cannot be assumed for full compliance. This

documentation is updated regularly. Necessary corrections and appropriate additions are always included in

subsequent versions.

As of: 07/2013

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

3

TABLE OF CONTENTS

1 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

2 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

2.1 Features ..................................................................................................................7

2.2 Assembly ................................................................................................................7

3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

3.1 Telescopic tube .......................................................................................................8

3.2 Flat duct (GS62-Corner) .........................................................................................8

4 Functional elements / interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

4.1 GS61 PSU ..............................................................................................................9

5 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

5.1 Installation preparation ...........................................................................................9

5.2 PSU .......................................................................................................................10

5.3 Telescopic tube ....................................................................................................10

5.4 Fitting the telescopic tube into the wall ................................................................12

5.5 Protective hood.....................................................................................................13

5.6 Nonreturn valve .....................................................................................................14

5.7 Fan housing ..........................................................................................................14

5.8 Inner baffle ............................................................................................................16

5.9 Flat duct (GS62-Corner) .......................................................................................17

5.10 Dimensional drawings...........................................................................................18

5.10.1 GS62 with protective hood ...................................................................................18

5.10.2 GS62 with GS62-Corner .......................................................................................20

6 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22

7 Technical details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

7.1 GS62 air extraction system ..................................................................................24

7.2 GS61 PSU ............................................................................................................25

7.3 Fan ........................................................................................................................25

7.4 Telescopic tube .....................................................................................................25

7.5 Inner baffle ............................................................................................................26

7.6 Protective hood.....................................................................................................26

7.7 Flat duct ................................................................................................................26

7.8 Grate with sleeve ..................................................................................................26

7.9 Fan housing ..........................................................................................................26

7.10 Nonreturn valve .....................................................................................................26

8 Deliverables, accessories and spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . .27

8.1 Deliverables ..........................................................................................................27

8.2 Accessories ..........................................................................................................27

8.3 Spare parts ...........................................................................................................27

4

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

TABLE OF CONTENTS

9 Maintenance and repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

10 Troubleshooting and disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

10.1 Troubleshooting .......................................................................................................... 29

10.1.1 GS62 air extraction system ........................................................................................ 29

10.1.2 Functional modules .................................................................................................... 29

10.2 Disposal ...................................................................................................................... 29

11 Warranty and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

11.1 Terms of warranty ....................................................................................................... 30

11.2 Service ........................................................................................................................ 30

Legal notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

5

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

SYSTEM OVERVIEW

3

2

1

1 SYSTEM OVERVIEW

The GS62 was developed for the ventilation of rooms with outside windows in single and multiple occupancy

houses, hotels and guest houses. It is an air extraction system that works without heat recovery and with direct

current.

Application areas

The GS62 is fitted into the outside wall of a building and can be used for:

• Bathrooms / toilets

• Kitchens

• Utility rooms

• Hallways

Variants

The base element of every variant is the combination of wall mounting sleeve (1), fan housing (2) with integrated

fan (3) and the GS61 PSU.

GS62 base element GS61 PSU

The GS62 can optionally be connected to the following modules, offering extended functionality as compared

to a standard On/Off switch*

)

:

• R60 controller

• Delay switch

• Hygrostat

Note - The description and connection options of these modules are in additional,

accompanying installation and operating instructions for the GS61 air extraction system.

Interior room side

The ventilation system is covered by a baffle on the interior wall side. Inside baffles can be

ordered:

• in colors white/silver/stainless/gold (material: is plastic, curved shape)

• in opaque glass (straight shape)

• as a frame for affixing a glass or ceramic tile (material: plastic, straight shape)

*) The On/Off switch is not included in the delivery

6

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

SYSTEM OVERVIEW

COMPONENT DESCRIPTION FEATURES ORDER NO.

GS62 - - 1001-0120

GS62-Corner 500 Comprising flat duct (500mm), 2 x wall

brackets and moffit grate

White 1506-0060

GS62-Corner 1000 Comprising flat duct (1000mm), 2 x wall

brackets and moffit grate

White 1506-0061

2-part telescopic tube Extension (500mm) for standard telescopic tube - 1002-0021

GS62 protective hood High-grade steel, powder-coated

White (RAL 9016) 1508-0043

Gray (RAL 7011) 1508-0044

High-grade steel, sanded Bare*

)

1508-0046

Inside baffle Plastic (curved) White 1505-0020

Stainless 1505-0021

Gold**

)

1505-0024

Silver **

)

1505-0025

Glass Opaque 1505-0022

Frame Decor of tile 1505-0023

R60 controller Fan speed regulator 1002-0006

Delay timer Button with integrated delay controller 1002-0011

Hygrostat Supports regulation of relative humidity 1002-0015

GS62 WITH PROTECTIVE HOOD GS62 WITH GS62-CORNER

Exterior room side

In the direction of the exterior room side, the ventilation system can be closed either with a

• protective hood (white/gray/bare

1)

) or

• the GS62-Corner 500 / GS62-Corner 1000, depending on preference and practical requirements

The GS62-Corner is used mainly when a building is retrofitted with insulation as part of renovation measures.

The air duct is embedded in the insulation and the airflow is directed out in the window reveal. The wall opening

for the ventilation system must therefore be in close proximity to the window. The GS62-Corner 500 is used

for a 250 … 450mm distance, the GS62-Corner 1000 for a 451 .. 950mm distance, between wall opening and

window reveal.

Validity

The installation and operating instructions apply for these elements:

*) Install only after coating (by customer) with Nano Set ,included

**) Not stock items (lead time on request)

7

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

DESCRIPTION

4

9 8 7

6

5

321

13

12

10

11

8 7 6

5

4

321

11

10

9

4

9

8

7

6

5

3

2

1

13

12

10

11

8

7

6

5

4

3

2

1

11

10

9

2 DESCRIPTION

The GS62 air discharge system is used to expel old air from a room. The fan is preinstalled in the housing for

ex works deliveries.

2.1 Features

• Low power consumption of fan (approx. 70% less than comparable AC fans)

• Use for wall thicknesses of 150 ... 550mm, to 950mm with telescopic extension

• Hole for telescopic tube Ø 115mm

• Use for distance between wall opening and window reveal of 350 ... 950mm (GS62-Corner)

• Combination of the base element with six inside baffles of different designs, shapes and colors,

and with three protective hoods of different colors, or the GS62-Corner in white

2.2 Assembly

GS62 WITH PROTECTIVE HOOD GS2 WITH GS62-CORNER

Interior plaster Interior plaster

Fan housing Fan housing

Inside baffle Inside baffle

Fan Fan

Nonreturn valve Nonreturn valve

Telescopic tube, 2-part (sleeve with tube) Telescopic tube, 2-part (sleeve with tube)

Protective hood rear panel Window

Protective hood cover Grate

Exterior plaster Window ledge

Insulation Duct

Masonry Exterior plaster

Insulation

Masonry

Figure 1: GS62 assembly

1

2

4

3

5

6

7

8

99

1010

1111

12

13

8

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

OPERATING CONDITIONS

3 OPERATING CONDITIONS

Caution - Only use the GS62 in rooms that are free of aggressive and caustic gases, and

extreme dust exposure. This will ensure reliable functioning of the fan.

3.1 Telescopic tube

Standard variant

The length of the standard variant of the telescopic tube is 550mm, meaning it can be used for maximum wall

thicknesses of 550mm. For wall thicknesses of 325 ... 550mm, the telescopic tube is continuously adjustable.

The sleeve can be shortened by a maximum of 150mm for wall thicknesses shorter than 325mm.

Note - The minimum permitted wall thickness when using the standard variant of the telescopic

tube is 150mm.

The sleeve of the telescopic tube on the interior wall side is covered by the fan housing and an Inside baffle.

Extension

An extension is available as an option for walls having a thickness from 550mm to 1000mm (maximum). The

extension is a second telescopic tube without fan. The order number for the extension is under Validity in Sec-

tion System overview.

2-part telescopic tube (extension)

Fan housing

Inside baffle

Fan

Nonreturn valve

2-part telescopic tube (sleeve with tube)

Protective hood rear panel

Protective hood cover

Figure 2: GS62 assembly with two telescopic tubes (extension)

3.2 Flat duct (GS62-Corner)

The length of the flat duct (GS62-Corner 500) is 500mm, and so can be used for gaps between wall open-

ing and window reveal of 250 ... 450mm. If the gap between wall opening and window reveal is greater than

400mm, a flat duct 1000mm in length can be ordered as an option (GS62-Corner 1000).

Note - The maximum permitted gap between wall opening and window reveal is 950mm.

1

2

4

3

5

6

7

8

2-part telescopic tube (extension)

3

2-part telescopic tube (extension)

2

2-part telescopic tube (sleeve with tube)

5

2-part telescopic tube (sleeve with tube) 2-part telescopic tube (sleeve with tube)

Nonreturn valve

4

6

8

1

7

9

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

FUNCTIONAL ELEMENTS/INSTALLATION

4 FUNCTIONAL ELEMENTS / INTERFACES

4.1 GS61 PSU

Power supply (AC 230V, 50 Hz)

Fan connector (-)

Fan connector (+) or functional module (+)

Figure 3: Connectors on GS61 PSU

5 INSTALLATION

5.1 Installation preparation

Dimensions

Name Comprising: Length (mm) LxW / diameter (mm)

Hole for Wall thickness Ø 115

telescopic tube -

(with insulation, interior/exterior plaster)

Telescopic tube Sleeve 300 Ø 107

Tube 300 Ø 103

Extension Identical in design to combination Wall mounting sleeve / telescopic tube

Flat duct - 500 209x65

- 1000

Opening for - 87 Ø ≥ 75

wall mounting box

Wall mounting box - 87 Ø 73

Note - Keep a minimum distance of 100mm from the center of the wall mounting sleeve to

walls, to components in the interior area as well as to fixtures and fittings.

Wall holes and cable laying

Danger - Make the opening for the wall mounting box outside protective areas 0 to 2 of the

room. This will ensure that no moisture can penetrate in.

1. Make two holes in the masonry - one (Ø75) for the wall mounting box and one (Ø115) for the telescopic

tube. Ensure that the hole for the wall mounting sleeve of the GS62 is at an angle of 1-2° to the outside

wall so that condensation is drained away reliably.

2. Lay the 2-wire connecting lead (red/white) for the wall mounting box in the cable duct such that the cable

ends project out of each wall opening by at least 150mm. This ensures that the PSU and switch can be

connected with terminal blocks.

Note - The dimensional drawings for all holes are in Section Dimensional drawings.

1

2

10

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION

5

2

3

1

4

5.2 PSU

Danger - Before starting any work on electrical systems, disconnect all relevant equipment

from the power supply. When wiring the power supply, observe the requirements of Safety

Class II.

GS61 PSU

Cavity

PSU

Fan connector (terminal, 2-pin)

Wall mounting box

Cavity separating wall

Figure 4: Fitting the PSU

1. Make two holes on the wall mounting box (4) - these must be in different cavities (1).

2. Separately guide the cables for the PSU and the fan through one hole each and insert the wall mounting

box.

3. Connect the fan cable to the PSU (2) using the 2-pin terminal (3).

4. Ensure correct polarity connections are made. Information on this is in Section Electrical connection.

Note - The wall mounting box must always be shut.

GS61 PSU - Attach a standard or optionally available On/Off switch. Order number informa-

tion is in Section Deliverables and accessories.

5.3 Telescopic tube

GS62 with protective hood GS62 with GS62-Corner

Exterior plaster

Insulation

Masonry

Interior plaster

Figure 5: Determining the wall thickness

1

2

4

3

5

2

1

3

4

Interior plaster

Exterior plaster

Insulation

Exterior plaster

Insulation

Exterior plaster

Insulation

Exterior plaster

Insulation

Interior plaster

Insulation

Exterior plaster

Interior plaster

Exterior plaster

Insulation

Masonry

Interior plaster

Masonry

Insulation

Masonry

Insulation

Masonry

Insulation

Exterior plaster

1

Exterior plaster

4

Exterior plaster

otective hood GS62 with GS62-Cor

11

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION

GS62 with protective hood GS62 with GS62-Corner

1. Determine the exact wall thickness by 1. Determine the exact wall thickness by

adding the thicknesses of exterior plaster, insulation, adding the thicknesses of masonry and

masonry and interior plaster. interior plaster.

2. Add 5mm for the projection at the 2. Add 10mm for the projection at the

outside plaster edge. The projection is required for masonry. The projection is required for correct

correct installation of the protection hood. installation of the flat duct.

3. Shorten or extend the telescopic tube in line with the wall thickness determined. The following table shows

an overview of the exact procedure.

Standard telescopic tube 2 telescopic tubes (extension)

Wall thickness (mm) Wall thickness (mm)

150 ... 324 325 ... 550 551 ... 1000

Seal all the joints of the tube and sleeve with durable, watertight adhesive tape*

)

. This fuses together the

joints. When condensation forms in the telescopic tube, the sealed joints prevent

moisture from penetrating into the wall.

*) Not included in the delivery.

otective hood GS62 with GS62-Cor

1. Determine the exact wall thickness by

. interior plaster.

2. Add 10mm for the projection at the

equired for masonry. The projection is required for correct

rect installation of the protection hood. installation of the flat duct.

d telescopic tube 2 telescopic tubes (extension)

Wall thickness (mm) Wall thickness (mm)

150 ... 324 325 ... 550 551 ... 1000

a)

b)

c)

Shorten the sleeve to

the wall thickness using

a grinder or jigsaw.

Subtract 20mm from the

wall thickness and shorten

the tube to the difference

using a grinder or jigsaw.

-

Keep pulling the telescopic

tube out of the sleeve until

the length corresponds

to the wall thickness.

-

Connect up the two telescopic tubes

such that they overlap by

at least 50mm.

Protect the tube combination using

durable, watertight adhesive tape*

)

.

Align the tube combination to the length

corresponding to the wall thickness.

12

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION

5.4 Fitting the telescopic tube into the wall

1. Insert the telescopic tube (3) into the wall opening. Ensure that the fastening elements (4) for the protec-

tive hood are inserted horizontally.

Masonry

Free area between

masonry and telescopic tube

Telescopic tube

Securing elements for

protective hood

Figure 6: Inserting the telescopic tube

2. Align the telescopic tube at an angle of 1-2° to the outside wall Use

polystyrene or wood wedges for securing.

Note - GS62 with protective hood:

Ensure that the two elements for securing the protective

hood (4) to the outer wall protrude no more than 2mm.

GS62 with GS62-Corner:

Ensure that the telescopic tube protrudes 10-15mm on the outside

wall. This ensures that the flat duct can be fitted correctly. Before inserting the telescopic tube,

turn the two brass sleeves upwards and affix the all-round sealing tape (included) at a distance

of 8mm from the outer edge of the telescopic tube (see Figure 11: no.

)

3. Use 2-component foam to fully foam the free area between the masonry and

telescopic tube (2).

4. Cut the installation foam inside and outside flush to the wall.

5. GS62 with GS62-Corner: Stick sealing tape all around the projection of the telescopic tube.

Caution

- The GS62 is not suitable for drying out buildings. Do not use the GS62 whilst con-

struction work is being carried out in the building. Close the telescopic tube to protect the fan.

This safeguards reliable functioning of the GS62 following completion of building work.

1

14

2

4

3

ca. 10 mm

4

3

2

1

13

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION

2

1

5.5 Protective hood

Protective hood rear panel

Sealing tape

Holes for securing the rear panel to

the telescopic tube

Figure 7: Protective hood rear panel

1. Apply the sealing tape (included) on the rear panel as in Figure 7. Ensure to keep a gap of approx. 7mm

on the left and right from the outer edge for sliding on the protective hood.

2. Turn the board over. The sealing tape is facing the facade.

Protective hood cover

Sealing tape

Figure 8: Protective hood cover

3. Use the two screws (included) to attach the rear panel of the protective hood to the two

fastening elements of the telescopic tube

4. Seal the protective hood at the top edge as in Figure 8

5. Slide the protective hood*

)

onto the rear panel from above

Note: Remove the polystyrene spacer from the telescopic tube before fitting the protective

hood

*)

Use of the GS62-Blank protective hood only after coating (by customer) with Nano Set included

1

2

3

2

1

3

14

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION

5.6 Nonreturn valve

Fan housing

with fan

Nonreturn valve

Figure 9: Nonreturn valve and fan housing

1.

Insert the nonreturn valve (2) into the rear of the fan housing (1)

2.

Allow the four attachment hooks to audibly click into place

5.7 Fan housing

Housing screen

Housing cover

Fan housing

Hole for cable feedthrough

(PSU connection)

Nonreturn valve

Telescopic tube

Connector cable (2-wire) po-

sition from the masonry for

fan and PSU connection

Masonry

Hole for wall

attachment (4 x)

Figure 10: Fan housing installation on interior room side

1

2

3

4

5

6

7

8

9

1

2

15

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION

Note: The polystyrene spacer, if still in, and any dirt residue must be removed from the tele-

scopic tube before the fan housing is fitted. Also, the 2-wire cable for connecting the fan to

the PSU must be wired at the designated place (7).

1. Remove the housing screen (1) and housing cover (2) from the fan housing (3). Undo the two screws to

remove the housing cover. The housing screen is clipped on.

2. Before final installation, drill four holes (Ø 6mm) in the wall for the wall attachment (9). To do this, position

the fan housing into the telescopic tube (6) from the interior wall side, align it and mark the places for

drilling at the four external holes for wall attachment (9) of the fan housing. Remove the fan housing, drill

the wall holes and insert the dowels (included).

3. Position the fan housing (3), including nonreturn valve (5), into the telescopic tube (6) from the interior

wall side. Before pushing the housing all the way to the wall, route the 2-wire cable for the fan and PSU

connection through the cable feedthrough hole (7).

4. Push the fan housing all the way to the wall and attach it to the masonry using the four screws (included)

at the four external holes for wall attachment (9).

5. Connect the cable in the fan housing to the connectors provided. Information on this is in Section Elec-

trical connection on Page 23.

6. Refit the housing screen (1) and housing cover (2).

16

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION

5.8 Inside baffle

Fan housing

Inside baffle

Mounting elements (x 4)

Figure 9: Fitting the Inside baffle

1. Put the Inside baffle (2) onto the fan housing (1) - as seen from the inside panel.

2. Allow the four mounting elements (3) to audibly click into place

Figure 10: (from left to right) inside baffle (curved plastic), glass inside baffle, tile inside baffle

1

2

3

2

17

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION

35

11 10

8

4

9

6

7

3

14

1

5

2

13 12

70

( ) -35

5.9 Flat duct (GS62-Corner)

The flat duct is mounted onto the telescopic tube instead of the outer hood.

Note - Ensure that sealing tape is applied all around the telescopic tube.

Make sure that the flat duct is mounted at an angle of 1-2° towards the window reveal so that

any condensation is reliably drained away.

Masonry Exterior plaster

Interior plaster Sleeve (reveal grate)

Telescopic tube Insulation

inside baffle Wall bracket (x 2)

Fan housing Flat duct*

)

Window Wall hole break-out (left/right)

Window frame Sealing tape

*

)

Use the 500mm flat duct when the maximum value of y+z = 450mm.

Use the 1000mm flat duct when y+z is between 451mm and 950mm.

Figure 10: Fitting the flat duct (complete unit)

1. Add |y| and |z|.

2. Subtract 35mm from this value for the end position of the duct.

3. Shorten the flat duct on the side opposite the hole for the telescopic tube down to

the length determined: overall length of flat duct = 70mm + (y+z) - 35mm.

1

8

2 9

4

3

5

6

7

10

11

12

13

14

Masonry Exterior plaster

Interior plaster Sleeve (reveal grate)

Telescopic tube Insulation

inside baffle Wall bracket (x 2)

Fan housing Flat duct*

Window Wall hole break-out (left/right)

Window frame Sealing tape

Interior plaster Sleeve (reveal grate)

Telescopic tube Insulation

inside baffle Wall bracket (x 2)

Fan housing Flat duct*

Window Wall hole break-out (left/right)

Window frame Sealing tape

Masonry Exterior plaster

Interior plaster Sleeve (reveal grate)

Telescopic tube Insulation

inside baffle Wall bracket (x 2)

Fan housing Flat duct*

Window Wall hole break-out (left/right)

Window frame Sealing tape

Masonry Exterior plaster

18

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION

Telescopic tube sealing tape

Wall bracket (x 2)

Window reveal

Wall holder fixing fixing screws (x 4)

Insulation

Exterior plaster

Telescopic tube

Masonry

Figure 11: Fitting of wall brackets

1. Use the fixing screws (4) to attach the two wall brackets (2) to the outer wall.

Flat duct

Wall bracket (x 2)

Grate

Sleeve

Figure 12: Fitting of sleeve and grate

2. Push the circular opening on the flat duct onto the telescopic tube and secure it at the wall brackets (2).

3. Push the sleeve (4) for attaching the grate onto the flat duct.

4. Push the grate (3) onto the sleeve until it audible clicks into place (additional securing with acrylic as

required).

5.10 Dimensional drawings

5.10.1 GS62 with protective hood

Wall opening

Protective hood (outline)

Exterior side element (e.g. window, door)

Shown in the drawing is the situation most

aesthetic visually - the top edge of the protective hood is flush with

the top edge of the structural element or with the lower edge of the

soffit on the lintel.

Figure 13: Wall opening dimensional drawing, GS62 telescopic tube with protective hood (exterior view)

Note

- Keep to the minimum distance of 250mm away from other components on the exterior.

1

2

4

5

6

7

8

7

8

3

≥ 250

Ø1

15

78

2

1

19

13 GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION







ุ











300

Ø107

Ø103 1

≥ 50

Ø73

71

61









Air extraction system (as a complete assembly)

Figure 14: Dimensional drawing for GS62 with protective hood

Telescopic tube (extension)

Figure 15: Dimensional drawing for 2-part telescopic tube (extension)

Wall mounting box

Figure 16: Dimensional drawing for wall mounting box

Protective hood

Figure 17: Dimensional drawing for GS62 protective hood

20

GS62 Air Extraction System • Installation and Operating Instructions 09/2013

INSTALLATION INSTALLATION





3

2

1

Inside baffle

Figure 18: Dimension drawing from left to right GS inside baffle (white, stainless, gold and silver), glass, tile

5.10.2 GS62 with GS62-Corner

Note -

The dimensional drawings for these components are in Section Dimensional drawings

for GS62 with protective hood - telescopic tube (extension), wall mounting box and inside baffle

Wall opening

Flat duct (outline)

Lower edge of soffit

(lintel)*

Outer edge of reveal

(masonry)

*) Take into consideration

insulation thickness and

any roller shutters

Figure 19: Wall opening dimensional drawing, GS62 telescopic tube with GS62-Corner (exterior view)

*

≥ 250

Ø1

15

≥ 200

102

2

1

3

Page is loading ...

inVENTer GS62 Installation And Operating Instructions Manual

inVENTer GS62 Installation And Operating Instructions Manual

Related papers

Other documents