Signature Hardware SH429820 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
SH429820
Type
Installation guide

Signature Hardware SH429820 is a shower pan designed for use in bathroom renovations. It is made of durable acrylic and features a textured bottom for added slip resistance. The pan is also easy to clean and maintain, making it a great choice for busy families.

Signature Hardware SH429820 is a shower pan designed for use in bathroom renovations. It is made of durable acrylic and features a textured bottom for added slip resistance. The pan is also easy to clean and maintain, making it a great choice for busy families.

SHOWER PAN INSTALLATION INSTRUCTIONS
GETTING STARTED
BEFORE YOU BEGIN
We recommend consulting a professional if you are
unfamiliar with installing plumbing fixtures. Signature
Hardware accepts no liability for any damage to the
faucet, plumbing, sink, counter top, or for personal injury
during installation.
Observe all local plumbing and building codes.
Unpack and inspect the products for shipping damage. If
any damage is found, contact our Customer Relations
team at 1-866-855-2284.
Ensure that you have gathered all the required
materials that are needed for the installation.
TOOLS AND MATERIALS:
Plumbers
Tape
Thread
Sealant
1Shower Pan Installation Instructions
Tape Measure
Level
Flathead
Screwdriver
Phillips
Screwdriver
Drill
Silicone Sealant
(100% Neutral
Cure)
Screws
Wood Shims
Mortar
Marker
SHOWER PAN INSTALLATION INSTRUCTIONS
INSTALLATION
3. Set the shower pan into the prepared alcove. Use a
level to ensure that the pan is level for proper drainage.
Use wooden shims where necessary. Mark the lip of
the base and wall studs where each of them meet.
1. Measure the area, as well as the shower pan, to
ensure fitment. Take into consideration any finished
wall materials as well the shower door being installed,
if applicable.
2. Complete the rough-in plumbing. A minimum 5”x5”
opening should be prepared in the slab or sub floor for
drain clearance. A 2” diameter waste pipe will be
needed to make the drain connection.
2Shower Pan Installation Instructions
4. Remove the shower pan and prepare the setting.
Spread mortar appropriately under the base of the
pan, then set the pan back into position.
5”x5”
mortar
SHOWER PAN INSTALLATION INSTRUCTIONS
7. Proceed to the installation of any framing and
shower system rough-in. If using drywall for shower
walls, be sure to waterproof the surface. If tiling the
walls, use a waterproof adhesive for installation.
Note: Refer to the drawing below for proper installa-
tion order.
6. Install the drain assembly. Connect the drain
assembly to the waste pipe using the rubber gasket
that is provided. Use a screwdriver to press the
gasket into place, ensuring that it is fully seated. Snap
the strainer into the pan.
3Shower Pan Installation Instructions
5. While mortar is still wet, press the pan into place
until the markings on the pan and wall studs realign.
Use screws to clamp the lip of the pan to the studs,
holding it in place. Do not drill through the pan.
Important: Let the mortar harden overnight before
moving on. Do not stand or place heavy objects on
the pan while it is curing.
leave small
clearance
between
studs and
lip of pan
shower
pan
waterproof
sealant
tile
drywall (1/2” is
recommended)
x
strainer
rubber
gasket
2” diameter
waste pipe
  • Page 1 1
  • Page 2 2
  • Page 3 3

Signature Hardware SH429820 Installation guide

Signature Hardware
Brand
Signature Hardware
Model
SH429820
Type
Installation guide

Signature Hardware SH429820 is a shower pan designed for use in bathroom renovations. It is made of durable acrylic and features a textured bottom for added slip resistance. The pan is also easy to clean and maintain, making it a great choice for busy families.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents