Maytag LSG7806AAQ Installation guide

Brand: Maytag

Model: LSG7806AAQ

Category: Water heaters & boilers

Type: Installation guide

LEAVE THESE INSTRUCTIONS WITH THE OWNER

iMPORTANT TO iNSTALLER

REMOVE THE DOOR FROIVl ALL DISCARDED

APPLIANCES SUCH AS DRYERS AND

COMBINATION WASHER/DRYERS TO AVOID

THE DANGER OF A CHILD SUFFOCATING

SHOULD HE/SHE CRAWL INSIDE AND THE

DOOR BE SHUT.

THE APPLIANCE MUST NOT BE INSTALLED

OR STORED IN AN AREA WHERE IT WILL BE

EXPOSED TO WATER AND/OR WEATHER.

U.S. MODELS

PLEASE READ THE FOLLOWING INSTRUC-

TIONS CAREFULLY BEFORE STARTING TO

INSTALL THE DRYER. FOR GAS DRYERS,

THE INSTALLATION MUST CONFORM WITH

THE NATIONAL FUEL GAS CODE ANSI

Z223.1, LATEST REVISION. ANY QUESTIONS

CONCERNING THIS SHOULD BE REFERRED

TO THE LOCAL GAS UTILITY.

CANADIAN MODELS

PLEASE READ THE FOLLOWING INSTRUC-

TIONS CAREFULLY BEFORE STARTING TO

INSTALL THE DRYER. FOR GAS DRYER

INSTALLATION, REFER TO STANDARD

CAN/CGA B149 (.1 OR .2) INSTALLATION

CODE. ANY QUESTIONS SHOULD BE

REFERRED TO THE LOCAL GAS UTILITY.

This folder contains information of interest to the

owner. After the appliance has been properly

instafled, LEAVE THESE INSTRUCTIONS

WITH THE OWNER.

SERVICE CALLS PERFORMED

AS A RESULT OF POOR

INSTALLATION ARE THE

RESPONSIBILITY OF THE

INSTALLER.

printed in U,S,A, 6 3717020

iMPORTANT TO OWNER

Retain these instructions for future reference.

This new Maytag appliance is designed to serve

you dependably for many years. However, it

cannot do so unless provided with sufficient

electrical power, suitable exhausting and if a gas

model, adequate gas supply. We urge you to

read this carefully to make sure all requirements

are met.

Operating instructions, safety precautions and

your warranty are in the accessory package with

each appliance. Read the operating instructions

carefully.

NOTE: A wiring diagram for the dryer is located

on the inside of the dryer access panel. A wiring

diagram for the washer is located on the inside

of the washer cabinet.

Untape and open washer lid. Remove installa-

tion accessory package, fill hoses and close lid.

Leave tub block in place until installation is

complete. Be sure to remove tub block after

installation is complete and before use!

Using the carton corner posts stacked in pairs,

lay the washer on the posts on the left side.

Remove the crate base wires from the carton

base. Use pliers or screwdriver to pry wires from

wood. (Do not kick the shipping base off the

washer.)

Run washer rear legs all the way up into the rear

corner brackets. Lock in place by tightening lock

nuts up against base. Leave front legs loose for

leveling later.

To remove carton, cut around bottom of carton

on or below dotted line. Cut down each corner

of carton (vertically) and "peel" carton away from

stacked washer/dryer. Fold carton material for

removal. Check the unit for shipping damage.

Remove the tape between the washer cabinet

and the dryer stand. Disconnect the control wire

harness which leads from the dryer to the

washer. You will need to depress the locking

tabs to separate the connector.

Locking Tabs

From the back of the stacked washer/dryer,

grasp the dryer and stand. Pull dryer and stand

back and off of washer and shipping base. As

dryer and stand are pulled back, carefully drop

dryer stand rear legs to _,

the floor before clearing

shipping base. (Do not

drop dryer and stand

off of shipping base!)

Install the vinyl feet on the washer legs.

Lay a piece of the shipping cardboard along the

bottom edge of the cabinet and stand the washer

back up. (The cardboard protects the lower

edge at the cabinet and the floor when standing

the washer back up.)

NOTE: With the rear washer legs adjusted up,

cabinet corner brackets in the rear can touch

and damage floor if caution is not used when

moving washer.

The dryer and stand are installed first.

Necessary electrical, gas (if gas stacked washer/

dryer) and vent connections are made as dryer

and stand are put in position and leveled. Let's

first look at what facilities are needed.

printed in U,S,A,

PREJNSTALLATJON CONSiDERATiONS

Location: The stacked washer/dryer is approved

for zero clearance installation on the sides and

the back (depending on venting used). The Ioca=

tion selected must take into consideration the

dimensions of the unit and convenience for cus=

tomer use and access in case service should be

needed. The floor must be capable of supporting

the weight of the unit (approximately 310 Ibs.)

plus water (approximately 150 Ibs.) and be stable

enough to prevent excessive vibration in spin

cycles. A floor which is adequate for the

standard washer is sufficient for the stacked

washer/dryer.

The following specifications and drawings show

dimensions and locations of fill valve, terminal

block (electric dryer), gas inlet (gas dryer) and

drain outlet.

STACKED WASHER AND DRYER

Basic Dimensions: 271/2W x 271/2 D x 73 H (min.) See drawings for complete dimensions.

Uncrated Weight: Approximately 31 0 Ibs.

KEY FACTS - WASHER

Capacity: Standard (16 gaL)

Water Usage: (full cycle)

36 (30 Imp.) gaL; 136 liters -large

28 (23 Imp.) gaL; 106 liters- medium

22 (18 Imp.) gaL; 83 liters -small

Motor: 1/2 H.R rated; 120 volt; 60 Hz; reversible, thermo-

protected against overload; automatic reset.

Power: .1 - .17 kwh depending on cycle

Hose Lengths: Inlet 4.0 feet, drain 4 feet

Installation Requirements: Hot and cold connections

with water pressure within 20 - 120 PSI range. At

least 140°R hot water and a drain.

KEY FACTS - DRYER

Air Fmow: 180CFM

Exhaust: 4" duct permits up to a maximum of 50 feet rigid

aluminum ductwork. Subtract 8 feet for each 90°

elbow, 8 feet for an exhaust hood. Dryer vented

out the back.

Motor: 1/4 H.R rated; 115 volt; 60 Hz thermoprotected

against overload; automatic reset.

Heat Source: Eiectric-Nichrome helix coil, 240 volt 3-wire,

4600 watts, (4500 wats for Canadian models

only), 30 amp fuse. Gas-single port burner 18000

BTU/hr.; electric ignition; automatic shut-off.

Capacity: 4.7 cu. ft, .13 cu. m.

Drum Speed: Approximately 47.5 RPM

Emectrical Requirements: Electric Dryer - 240 volt 60 Hz

protected by a 30 amp fuse. Gas Dryer - 115

volt electrical outlet properly grounded and

protected by a 15 amp fuse.

iNSTALLATiON SHOWING

DiMENSiONS ELECTRICAL/WATER/DRAIN BOX

GAS DRYER CONNECTION

2_" BEHIND WASHER-ELECTRIC DRYER

I_ 53.3 crn q

I /69.9 cm

69,9 cm

2 printed in U.S.A.

ALCOVE OR CLOSET

When the stacked washer/dryer is to be installed

in an alcove area or a closet, clearance should

be provided around the unit for an adequate air

supply and for ease of installation and servicing.

An appliance installed in a closet shall have no

other fuel burning appliance installed in the

same closet, such as gas furnace, water heater

or space heater, etc.

The dryer must be exhausted to the outside to

minimize excessive lint accumulation and to

maintain good drying. We recommend allow-

ance for more clearance than the minimum

installation clearances as shown.

Ceiling

0"-- -- _0"

FRONTVIEW

! Sq: In.

penmg

--II-- SIDE t

1/2" VIEW

Exhaust the dryer using metal exhausting

material or exhaust kit (see your authorized

Maytag dealer), and locate in an area that

provides adequate make-up air. The exhaust

duct may not terminate beneath the mobile home.

MAKE=UP AiR

For proper operation of the dryer unit it is impor-

tant to make sure the location has adequate

make=up air. This is especially important in any

confined area such as bathroom or closet. There

must be at least two 36 square inch unobstructed

openings for intake air. This can be a Iouvered

door or other equivalent opening.

On gas dryer units in particular, adequate clear-

ance as noted on the dryer minimum clearance

label should be maintained to insure enough air

for combustion and the proper operation of the

dryer. The area where located must not

obstruct the flow of combustion or ventilating

air. When installing a Maytag Stacked Washer/

Dryer the following minimum clearances to

combustible surfaces must be maintained.

Clearance to wall, sides - 0 inches, top - 6 inches,

front - 1/2 inch to washer, rear - 0 inches with an

outside exhaust, 4 inches with an inside exhaust

(not recommended). See Exhausting section and

Installation Accessories for exhaust kits.

Each opening area must have a minimum of 36

square inches. These openings must not be

obstructed. (Louvered door with equivalent air

opening is acceptable.)

MOBILE HOME iNSTALLATiON

SERVICE ACCESS

Location should allow access to the front of the

unit for washer and dryer service. Access must

also be available to two screws at the top front

corners of the dryer front panel (on the top).

Installation of Maytag dryers certified by the

American Gas Association and bearing a label

stating they are suitable for installation in mobile

homes, must conform to the Manufactured

Home Construction and Safety Standard Title 24

CFR, Part 32-80.

When installing this appliance in a mobile home,

provisions for anchoring the dryer should be

made. An anchor bracket kit is available to fas-

ten dryer stand to the floor. Instructions for

installing the anchor brackets are contained in

each kit. (See your authorized Maytag dealer.)

All mobile home installations must be exhausted

to the outside with the exhaust duct termination

securely fastened to the mobile home structure,

using materials that will not support combustion.

The free air flow rate is approximately 180 cubic

feet per minute. The vent system carries lint and

moisture away and to the outside. The length of

the venting and the number of elbows affect the

air flow rate and the efficiency of the exhaust system.

DO NOT EXHAUST DRYER INTO ANY WALL,

CEIMNG, CRAWL SPACE OR A CONCEALED

SPACE OF A BUiLDiNG, VENT CONNECTION,

GAS VENT OR CHMNEY. THIS COULD

CREATE A FIRE HAZARD FROM UNT

EXPELLED BY THE DRYER. FOR THE SAME

REASON, WE RECOMMEND ONLY METAL

EXHAUST DUCT TO MiNIMiZE RESTRICTED

AIR FLOW AND RELIABLY toNSURE THE

CONTAINMENT OF EXHAUST AIRo HEAT AND

printed in U=S=A= 3

LINT. NEVER iNSTALL A SCREEN OVER

EXHAUST OUTLET. NEVER USE PLASTIC OR

OTHER COMBUSTIBLE DUCTWORK. AT

LEAST ONCE AYEAR, INSPECT AND CLEAN

iNTERIOR OF DUCTWORK. FREQUENTLY

CHECK AND CLEAN VENT HOODTO ASSURE

PROPER OPERATION.

A cbthes dryer produces combustibUe tint and

the area around the clothes dryer shouUd be kept

free of tint. DO NOT STORE FLAMMABLE

LIQUIDS OR MATERmALS NEAR A DRYER.

tt is recommended that the dryer be exhausted

to the outside using 4 inch rigid or flexible metaU

ducting.

When located in a bedroom, bathroom or cUoset,

the dryer must be exhausted to the outside.

The stacked washer/dryer can only be exhaust°

ed out the back. A 4 inch vent shouUd be

installed to accept the exhaust from the dryer.

To permit sufficient air circulation under the

exhaust hood, there shouUd be no less than a 12

inch cUearance between the bottom of the

exhaust hood and the ground. When possible

the exhaust hood shouUd not exhaust directly

into a window weft. DO NOT terminate exhaust

under a building.

NOTE: Where the exhaust hood is to be

installed through masonry, a special masonry

saw is necessary to cut the hole.

tnstall the exhaust hood and secure with screws

to the outside waft and seal with caulking compound.

DIRECT EXHAUST

An exhaust hood positioned to line up with the

dryer exhaust pipe can be installed directly

through an outside wall. This would be the

shortest and most direct exhaust method.

To exhaust up, route standard 4 inch diameter

ducting up the recess in the cabinet back using

the furnished retaining strap and screws to get

nearly flush to wall installation. To exhaust to the

side or down, install the furnished 4 inch long

duct with four"S" clips to the inner dryer exhaust,

then use standard 4 inch ducting. This will posi-

tion the dryer about 4ol/2 inches away from the

wall. Flush-to-wall side exhausting may be done

by going above the dryer before going sideways.

When exhausting down, wallboard can be

removed from the wall to get the dryer closer to

the wall by placing the exhaust pipe between

studs. Check toccata codes for required

exhaust cmearances.

Install ductwork from the dryer to exhaust hood.

All joints must be made so exhaust end of one

pipe is inside the intake end of next pipe. On

flexible metal ductwork, all joints should be

secured with a clamp. DO NOT use sheet metal

screws when assembling rigid ducting. Joints

should be taped.

EXHAUST HOOD TYPE

Number of i_ _ 2

90 ° Turns 4 1/2

inch T_---inch

Maximum length of 4 inch diameter

rigid metal duct

54 feet 44 feet

43 feet 33 feet

36 feet 26 feet

30 feet 20 feet

24 feet 14 feet

length of 4 inch diameter

stiff walled metal duct

Maximum

flexible

34 feet

26 feet

22 feet

18 feet

15 feet

27 feet

19 feet

17 feet

15 feet

13 feet

FLEXIBLE DUCTWORK

Flexible metal ductwork should not exceed 34

feet of straight 4 inch ducting. The exhaust hood

is equivalent to 8 feet of duct and each 90 ° bend

is equivalent to 8 feet. As an example, if an

exhaust hood is used and two 90 ° bends, the

maximum straight run would be 10 feet.

NOTE: if the radius of a bend with 4 inch duct is

12 inches or greater, the bend can be considered

a straight run. No more than three 90 ° bends

should be used in any run with an exhaust hood.

tf flexible metal exhaust ducting is used, the short

extension supplied with this machine can be

secured to the dryer exhaust with the clips and

the flexible metal duct can be clamped to the

short extension.

4 printed in U.S.A.

RiGiD DUCTWORK

Rigid metal ductwork should not exceed 54 feet

of straight 4 inch duct. Each 90 ° elbow and the

exhaust hood should be considered equivalent

to 8 feet of straight ductwork.

For example, if an exhaust hood and two 90 °

elbows are used, the maximum straight duct

allowed would be 26 feet. Not more than three

90 ° elbows should be used in any rigid ductwork

run with an exhaust hood. Four feet of straight

duct should be allowed between 90 ° elbows.

ELECTF{JCAL REQUJF{EMENTS

iMPORTANT SAFETY PRECAUTIONS

WARNING: To prevent unnecessary risk of fire,

electrical shock or personal injury, all wiring and

grounding must be done in accordance with

local codes, or in the absence of local codes,

with the National Electrical Code, ANSI/NFPA

(for the United States) or the Canadian Electrical

Code, CSA C22.1 (for Canada). It is the

personal responsibility and obligation of the

appliance owner to provide adequate electrical

service for this appliance.

OBSERVE ALL NATIONAL CODES AND

LOCAL CODES AND ORDINANCES

GAS DRYER UNITS

A 120 volt, 60 Hz 15 ampere fuse electrical

supply is required. An individual branch (or

separate) circuit serving only this appliance is

recommended. DO NOT USE AN EXTENSION

CORD unless it meets all requirements as out=

lined for grounding, polarizing (3-wire) and

capacity. Wire size should be at least No. 14.

BEFORE OPERATING OR TESTING, follow

grounding instructions in Grounding section.

ELECTRICAL GROUNDING IS

REQUIRED FOR THIS APPMANCE.

GROUNDING iNSTRUCTiONS

This appliance must be grounded. In the event

of malfunction or breakdown, grounding will

reduce the risk of electrical shock by providing a

path of least resistance for electric current. This

appliance is equipped with a cord having an

equipment=grounding conductor and a ground=

ing plug. The plug must be plugged into an out=

let that is properly installed and grounded in

accordance with all local codes and ordinances.

DANGER - Improper connection of the equip=

ment=grounding conductor can result in a risk of

electric shock. Check with a qualified electrician

or serviceman if you are in doubt as to whether

the appliance is properly grounded.

printed in U=S=A= 5

Do not modify the plug provided with the

appliance. If it will not fit the outlet, have a

proper outlet installed by a qualified electrician.

ADDiTiONAL GROUND

PROCEDURE WHERE LOCAL

CODE PERMITS.

A grounding kit (Part No. 12001875) is available.

tt contains the external ground wire, clamp,

ground screw and washer. Where approved, it is

recommended this additional ground be

installed. A suitable external ground connection

MUST be determined prior to wire hookup.

Consult local building officials and qualified

electrician in event any questions exist. Connect

ground wire to back of dryer unit using the

grounding screw and washer. Secure other end

of the ground wire to a COLD water pipe using

the clamp.

NEVER CONNECT GROUND WIRE TO

PLASTIC PLUMBING LINES, GAS OR HOT

WATER PIPES.

ALL GROUNDING AND WIRING MUST BE

DONE IN ACCORDANCE WITH NATIONAL

AND LOCAL CODES.

ELECTRIC DRYER UNITS

U.S. MODELS

Grounding Instructions

This electric dryer must be connected to a

grounded metal, permanent wiring system; or an

equipment grounding conductor must be run

with the circuit conductors and connected to the

equipment grounding terminal on the back panel.

Electric models are shipped with a ground strap

connected from the neutral (P2) terminal block

post to the frame of the dryer. The use of this

strap is permitted by the national electrical code.

The dryer electrical supply may be connected by

means of a new U.L listed power supply cord kit

rated at 240 volts minimum, 30 amperes with

three No. 10 copper wire conductors terminated

with closed loop terminals, open=end spade lugs

with turned up ends or with tinned leads.

P1 P2 PS

Strain

I [I IiJ Power

The power cord must be marked for use with a

clothes dryer and be retained with suitable strain

relief. If the dryer is to be installed in a mobile

home or an area where local codes do not

permit grounding through neutral, only 4

conductor power cord, rated and terminated as

above, may be used.

The electrical supply circuit should be fused

through a 30 ampere fuse or circuit breaker on

both sides of the line. The neutral line of the

service cord must always be connected to the

P2 terminal post. The two hot lines of the

service cord go to the P1 and P3 terminal block

posts. The neutral should not be fused or

broken. Be sure terminal block nuts are tight

and replace access cover.

Canadian models are shipped with approved

power cord sets attached.

G.RL

tf the electric dryer is protected by a GROUND

FAULT INTERRUPTER, follow the procedure on

the next page for a 4-wire hook-up.

6 printed in U,S,A,

4-WIRE RECEPTACLE

For a 4-wire hook-up, the frame of a 120/240 volt

machine must NOT be connected to neutral

terminals. JtMUST be connected to the 4th wire

(green) of the power supply or to the metallic

covering of a 3-wire supply.

tf a 4-wire receptacle of NEMA _o._t,c,e

type is used, a matcNng U.L list-

ed power supply cord (pigtail)

must be used. This cord contains

four No. 10 copper conductors

with spade or ring terminals on the dryer end.

The 4th (grounding) conductor must be identified

by a green cover and the neutral conductor by a

wNte cover. The cord should have a suitable

strain relief, and should be a minimum 4 feet

long. The power supply cord and strain relbf are

not provided with the dryer.

4-WIRE SYSTEM CONNECTIONS

1. Remove the terminal block cover.

2. Remove the ground strap screw from the

terminal block support. Fold the ground strap

over so both ends of the ground strap are

attached to the center terminal block post.

3. Connect the neutral (white) wire of the power

supply cord to the center (silver colored) terminal

of the terminal block. Connect the grounding

(green) wire of the cord to the terminal block

support using the ground strap screw.

3-Wire System with

Power Cord Attached

Ground

Strap

4-Wire System with

Power Cord Attached

Folded

Ground

Strap

Relief

4. Connect the other two wires of the cord to the

outer terminals of the terminal block.

5. Replace the terminal block cover.

208 VOLT OPERATION

A stacked washer/dryer model is available for

208 volt operation.

Canadian Models

All Canadian models are shipped with the power

cord attached. The dryer power cord should be

plugged into a 30 ampere receptacle and fused

through a 30 ampere fuse or comparable circuit

breaker on both sides of the line.

NOTE: It is not permissible to convert a dryer in

Canada to 208 volts. A 208 volt model is not

available for Canada.

WATER SUPPLY AND DRAIN

WATER SUPPLY

The water supply to the washer unit should be

capable of providing both adequate water

pressure and water temperature. The pressure

should fall within the range of 20 pounds per

square inch to 120 pounds per square inch

when the washer is filling. Note that this is flow

pressure and not static pressure. Low water

pressure will result in slow fill and could result in

a water valve sticking open after a fill.

The recommended temperature of the hot water

as delivered to the washer should be 140 ° R

Warm water temperature is a result of the mix of

the hot and cold water supplies. The final

temperature is dependent on both the pressure

and the temperatures of the hot and cold

supplies. The desired temperature for warm is

between 100 ° R and 105 ° R

DRAIN FACILITIES

The drain must be capable of accepting a flow

rate of approximately 20 gallons per minute. An

inside diameter of at least 1 1/2 inches is required.

L-_

printed in U,S,A, 7

36 inch standpipe recommended

tf standpipe is less than 36 inches (or floor

drain) - drain hose should be routed through the

clip to raise hose to the proper height, use clip

tie to securely hold drain hose in clip.

JnstaJlation accessory kits are available for other

types of drain facility conditions...see Washer

tnstaJlation Accessory Kits table on page 13.

The use of a laundry built-in wail box can greatly

simplify installation.

if the faucets and/or drain is located to either

side of the stacked washer/dryer, openings are

located in the dryer stand uprights to allow

hoses and power cords to be passed through.

This is to allow instaJlation against the back wail.

(This is dependent on venting used.)

GAS CONNECTION

Gas operated dryers are equipped with a burner

orifice for operation on NATURAL GAS. if the

dryer is to be operated on LP GAS, it must be

converted correctly for safety and proper

performance. Conversion kits from NATURAL to

LPG, or LPG to NATURAL are available through

your local Maytag dealer, if other conversions

are required, check with IocaJ gas utility for

specific information concerning conversion

requirement. NOTE: The conversion should

always be performed by a qualified service

technician.

NOTE: if the dryer is to be converted in

Canada, the conversion shall be carried out in

accordance with the requirements of the

provincial authorities having jurisdiction and in

accordance with the requirements of the CAN-

B149.1 and CAN1-B149.2 instaJlation code.

A 1/2 inch gas supply line is recommended and

must be reduced to connect to the 3/8 inch gas

line on the dryer.

iMPORTANT NOTE: When installing the gas

line, route it so that it will not interfere with the

washer once the washer is pushed back into

position. It is important to make sure the gas fine

does not come into contact with either the

washer drain hose or any part of the washer.

NOTE: A 3/8 inch x 1 inch pipe nipple is includ-

ed to adapt valve connection from a 3/8 inch

female to a 3/8 inch male t.RS. connection.

AdditionaJly, a 1/8 inch N.RT. (National Pipe

Thread) plugged tapping, accessible for test

gauge connection, must be installed immediately

upstream of the gas supply connection to the

dryer.

Dryer

., Gas Line

]]- 118" NPT Plug

Gas Line

Refer to your IocaJ gas utility or plumbing

contractor should you have questions on the

instaJlation of the plugged tapping.

The dryer and its individual shut-off valve must

be disconnected from the gas supply piping

system during any pressure testing of the

system at test pressures in excess of 1/2

RS.i.G.

The dryer must be isolated from the gas supply

piping system by closing its individual manual

shut-off valve during any pressure testing of the

gas supply piping system at test pressures equal

to or less than 1/2 RS.J.G.

The gas supply should be connected to the

dryer using pipe joint compound or a Teflon tape

on male thread connections. NOTE: Any pipe

joint compound used must be resistant to the

action of any liquefied petroleum gas.

Turn on gas supply and open the shut-off at the

gas valve. DO NOT use an open flame to

check for gas leaks. Check all gas connections

for leaks using a soap solution, if bubbles occur,

tighten the connections and recheck.

NOTE: As a courtesy, many IocaJ gas utilities

will inspect a gas appliance instaJlation. Check

with your utility to see if this service is provided

in your area.

GAS JGNmON

This dryer uses an automatic ignition system to

light the main burner when the dryer is turned

on.

8 printed in U.S.A.

iNSTALL DRYER UNIT AND STAND

The dryer and stand are installed first. With the

connections prepared for exhausting, electric

power and gas (if gas stacked washer/dryer, see

page 9), the dryer and stand are moved to the

location.

NOTE: When moving the dryer and stand on an

appliance hand truck, it is recommended that the

dryer and stand be trucked upside down.

Protective padding should be used to avoid

damage to the cabinet finish.

I []

Grasp the dryer and

stand. Pull away from

washer and off of

shipping base. Install

vinyl feet; in

Accessory Package

located in Washer.

Move dryer and stand

to location. Level by

adjusting leveling legs.

NOTE: The rear legs are "washer" legs

and use the larger feet.

[] GAS MODELS -

Connect gas line

using pipe joint

compound on

male threads, see

page 9 for GAS

CONNECTION.

ELECTRmC MODELS-

install electric power

cord (U.L Approved).

NOTE: Power cord

provided with

Canadian models.

Make appropriate

external ground

connection.

[]

See DETAILED Installation Instructions for

ELECTRICAL REQUIREMENTS AND

GROUNDING (pages 6°7).

Make exhaust

connections.

Exhaust connection

is lined up as the

dryer and stand are

moved back into

position.

See DETAILED

Installation

Instructions for

EXHAUSTING

(pages 4°6).

Adjust stand and

dryer into proper

location. Check

stand to make

sure unit is still

level. Level legs

and rear lower cross

bar. Tighten lock

nuts up against the

stand.

With dryer and stand in position, exhaust

vent connected, unit leveled and gas line

connected (if gas unit), power cord set

installed (if electric unit), plug power cord

into electric outlet.

printed in U=S=A= 9

DRYER iNSTALLATiON

Vent Kit - standard - 4" (10.16cm)

kit includes two elbows, three pipes and

one vent hood

Vent Hood- 4" (10.16cm) opening

Aluminum Pipe - 4" x 24" (10.16cm x 60.96cm

Aluminum Elbow - 4" (10.16cm)

Aluminum Window Plate - 15"x 20"

(38.10cm x 50.80cm) - 4" (10.16cm)

Flexible Vent Kit - contains wide opening vent

hood, wall plate, two clamps and flexible

aluminum vent duct

Flexible Aluminum Vent Duct - 4" (10.16cm)

diameter - 38" (81.28cm) length stretches

to 8' (2.44m)

Clamp for Flexible Aluminum Duct

Exhaust Deflector Kit -inside exhaust kit

Natural to LPG Conversion Kit for Gas Valve

Dacron Lint Bag

Grounding Kit - contains ground wire, clamp,

ground screw and washer

(Part No. 12001875)

iNSTALL WASHER UNiT

1, Remove top cover

shipping pads

taped to washer

top.

m Remove fill "t,

hoses.

Replace and

leave tub

block in place \--

until installation is

complete. Close rid.

3, Remove the crate ,_"---_%\

base wires from

oratebase.Use

pliers or screw- _-'f /

driver to pry from "_F-- _1-![_.... I[!

wood. Discard crate I i/_ Ill I

base

4, Run washer rear legs all the way up into

the rear corner brackets. Lock in place by

tightening lock nuts up against base.

Leave front legs loose for leveling later.

install the vinyl feet on the front washer legs.

Move the washer into position in front of

the dryer and stand. Use caution to avoid

floor damage because of the minimum

height of the rear legs.

NOTE: Before sliding washer back into

position, connect fill hoses and insert drain

hose in standpipe.

tnstall inlet hoses.

Run water through both water _._<x:_

faucets into a bucket to purge /_.o_S'_' _

the water line particles that __

might clog the hoses. While /,_ /,.(

running water through the _/_\\

faucets, determine which _', l\i ,_

faucet is HOT water and _...... S

place an identifying mark \\ " '

on it. Traditionally the HOT water faucet is

on the left.

insert one screen and

then one washer into the

faucet ends of the inlet

hoses (straight end of

hoses). The screens

t I

should be pointing @ @--wAsaE.

out to fit properly.

I I

10 printed in U,S,A,

Attach the inlet hoses

to the HOT and COLD

faucets. Being sure _-_

the hose marked " '

"HOT" is attached to / _.#

the HOT water faucet. ,, _,

Tighten by hand until i

snug and then 2/3 of a ;__

turn with pliers. Do

not overtighten.

Attach the 90 ° ends of _-7

the inlet hoses to the

HOT and COLD

connections on the

back of the washer.

HOT and COLD

connections are

identified by H & C

stamped on the

bracket, HOT on top, COLD on bottom.

Connect COLD (lower) hose first. Be sure

the hose marked "COLD" is attached to the

COLD ("C") connection. Tighten by hand

until snug and then 2/3 of a turn with pliers.

Do not overtighten.

Turn on faucets and check for leaks at the

faucets and at the machine connections, if

leak occurs, check for cross-threaded or

loose connections.

7, install drain hose.

HOSE

RETAINER

Place the drain hose in the drain

the hose is twisted after it has been placed

in the drain, adjust the end of the hose to

remove the twist. To remove the twist, turn

the short end of the hose while holding the

base of the hose stationary.

NOTE: If you must make an airtight seal,

an siphon break kit must be used.

LAUNDRY

STANDPIPE

UNIT

TIE

STRAP

To prevent accidental dislodging secure the

drain hose to the standpipe, inlet hose or

laundry tub with the tie strap provided in the

parts package.

NOTE: It is very important when connect-

ing the drain hose that it is properly installed

to minimize the chance of the hose

becoming damaged when the washer is

moved into position.

Move the washer into position in front of

the dryer and stand. Tip forward enough for

glides to clear the legs of the stand and

guide the glides into the slots on the top of

the stand legs.

9, Connect the two control cables, one from

the dryer and one from the washer, as

shown. Be sure the locking tabs are

engaged. This electrically mates the

washer and dryer.

printed in U.S.A. 1 1

IO,

11,

12,

Connect the dryer power cord to 120 volt

AC outlet for gas models. 240 volt outlet

for electric models.

Make appropriate external ground

connection. See DETAILED installation

instructions for

ELECTRICAL

REQUiRE-

MENTS AND

GROUNDING

(pages 6-7).

Slide washer a))the way back into stand.

Tabs on stand legs are to slide into the

washer front panel. Adjust the washer

front legs. Leve) washer on stand. Lock

leveling legs in position using lock nuts.

it is very iMPORTANT

that the washer sits in

the stand

properly. Unit

must be solid

and level.

Check unit to

finish leveling.

Be sure to lock

ALL leveling

leg lock nuts.

,, Remove tub block ring from washer tub

opening.

,, Verify that all instruction packages have

been removed from washer tub and

dryer drum.

See installation Checklists for washer

and dryer.

DRYER (NSTALLAT(ON CHECK MST

Dryer is plugged into electrical outlet and

is properly grounded.

Exhaust duct work is hooked up and

joints taped.

Plastic flexible duct is NOT used.

Use rigid or stiff-walled flexible metal vent

material.

Dryer is level with all legs firmly on the

floor, with the lock nuts tightened.

Vinyl feet have been installed.

Gas Models - gas is turned on, there are

no gas leaks.

Dryer runs, heats, shuts off.

Demonstrate use to consumer.

WASHER (NSTALLAT(ON CHECK L(ST

Tub block, parts package and instruc-

tions have been removed from the tub.

Water has been turned on. Checked

for leaks at faucets and water valve

connections.

Drain hose is properly located into

drain facility and is not damaged.

Washer has been leveled with legs

firmly on the floor. The front leveling

legs' locking nuts have been tightened.

Fill washer, checking for the correct

water temperature.

After the washer has filled, let the

washer agitate.

Spin the water out.

Demonstrate washer usage to consumer.

Be sure to leave these instructions and

the User's Guide with the owner.

WASHER (NSTALLAT(ON ACCESSORY K(TS

Part No°

12001875

12001585

12001586

12001599

211692

204986

Description

Grounding Kit

Drain Hose Extension

Siphon Break

Small Diameter Standpipe

Drain Hose

Non-Slip Disc

Carpet installation Disc

Application

Contains ground wire, clamp, ground screw and washer.

Extends drain hose for drain facilities higher

than 1.2 m (4 ft.).

Used when an air-tight connection exists between

drain hose and drain facility. Floor drain facilities.

Used when standpipe diameter is too small to

receive end of drain hose.

For painted/sloped floors.

For carpeted floors.

12 printed in U.S.A.

ADDiTiONAL iNFORMATiON

ODD CYCLE OPERATION

This Maytag stacked washer/dryer is manufac-

tured for operation on 60 Hz approved electrical

service. It is not designed for use on 50 Hz AC

electrical service and conversion of the product

from 60 to 50 cycle operation is not recom-

mended. For additional information on 50 cycle

products, write, MAYTAG INTERNATIONAL,

INC., 8700 Bryn Mawr Ave., Chicago, Illinois

60631 or GRAY DISTRIBUTING CO., LTD., RO.

Box 2597, Honolulu, Hawaii 96803.

No routine lubrication is required to maintain the

stacked washer/dryer, tn the event something

does need attention, contact an authorized

Maytag dealer or servicer.

All the cabinetry and external finishes are

protected against rust to keep product looking

well for many years. Cleaning and waxing will

provide additional protection to these finishes.

The washer top has a porcelain finish. Since

porcelain is "glass" bonded to metal, it is very

durable. Avoid damage from sharp blows of

objects or tools used around and in the appliance.

Clean the control panel with a soft damp cloth.

Avoid abrasive cleaners that would scratch sur-

face. A coat of household wax will reduce the

chance of scratches on the control panel surface.

CAUTION: If "spilled" or used improperly,

bleaches and other strong laundering chemicals

can permanently spot or stain finishes unless

wiped up immediately. Aerosol pretreated

products can also damage finish on control

panel. When using these products on garments

placed in the stacked washer/dryer, it is advisable

to avoid control panel area with the overspray.

WATER DAMAGE FROM

FLOODING

tn the event the stacked washer/dryer is

exposed to water from flooding, call your local

Maytag dealer before using. Always unplug the

appliance and have a qualified technician

inspect the appliance before any attempt is

made to operate the unit. Never wash product

inside and out with a garden hose or pressure

cleaning system.

REPLACEMENT PARTS

tf your unit requires replacement parts, contact

the dealer from whom you purchased your

appliance, or Maytag Appliance Sales Co.,

Customer Service Division, Box 2370, Cleveland,

Tennessee, 37320-2370, phone 1-800-688-9900,

for information on the nearest Maytag part

distributor.

Part and service manuals are available through

your dealer or nearest parts distributor.

printed in U,S,A, 13

Maytag LSG7806AAQ Installation guide

Brand: Maytag

Model: LSG7806AAQ

Category: Water heaters & boilers

Type: Installation guide

Download PDF

report

Maytag LSG7806AAQ Installation guide

Maytag LSG7806AAQ Installation guide

Related papers

Other documents