Epson perfection 3170 Installation guide

Brand: Epson

Model: perfection 3170

Type: Installation guide

Turn over

4XXXXXXRev.0

1-F BK

4XXXXXXRev.0

1-F Y

4XXXXXXRev.0

1-F M

4XXXXXXRev.0

1-F C

4XXXXXXRev.0

1-F BK2

EPSON Perfection™ 3170 Photo

Unpack Your Scanner

1Make sure you have all the accessories shown below for your EPSON®

scanner:

Note: The contents may vary in certain locations.

If you purchased the optional automatic document feeder (ADF), you will

also have these items:

2Remove all the packing tape, but leave the large sticker in place until you are

instructed to remove it.

Install the Software

Wait! You must install your software before connecting the scanner to

your computer. The installation process may take several minutes. Be sure

to close all open programs and turn off any virus protection programs.

If you don’t already have Adobe Photoshop or Photoshop Elements on your

computer, install Photoshop Elements from the CD-ROM included with your

scanner.

Note: These instructions are for Windows® and Macintosh® OS 8.6 to 9.x and

OS X 10.2.x.

1Insert the scanner software CD-ROM in the CD-ROM or DVD drive. The

installer starts automatically.

If it doesn’t start, do the following:

•Windows XP: Click Start, double-click My Computer, then double-click

EPSON.

•Windows 98, Me, and 2000: Double-click My Computer, then double-

click EPSON.

•Macintosh: Double-click the EPSON CD-ROM icon

2If you are using Mac OS 8.6 to 9.x, double-click the EPSON icon in the

EPSON folder.

If you are using Mac OS X, double-click the Mac OS X folder in the EPSON

folder, then double-click the EPSON icon. Enter your Administrator name

and password and click OK.

3Read the license agreement, then click Agree.

4At the Software Installation screen, click Install.

5Follow the on-screen instructions to install each program. Click Next or

Finish (Windows) or Quit (Macintosh) to continue, as needed. Note that

EPSON Smart Panel™ installs in several steps.

6At the end of the installation, click Exit.

7If you see a Product Registration screen, register your scanner as instructed.

At the last screen, click Done or close your browser.

Connect the Scanner

After your software is installed, it’s time to get connected.

1Remove the sticker from the back of the scanner.

2Locate the transportation lock on the back of the scanner and slide the lock

to the left, as shown below.

3Connect the power cord and AC adapter, as shown.

4Connect the AC adapter to the scanner.

5Plug the other end of the power cord into a grounded electrical outlet.

Caution:

•It is not possible to change the AC adapter’s input or output voltage. If the

label on the AC adapter does not show the correct voltage, contact your

dealer. Do not plug in the power cord.

•Whenever you unplug the scanner, wait at least 10 seconds before

plugging it back in. Rapidly plugging and unplugging the scanner can

damage it.

6Connect the cable for the built-in transparency unit.

7Use the USB cable that came with your scanner. Plug the square end of the

USB cable into the scanner’s USB port. Then plug the flat end into any

available USB port on your computer or hub.

Note: Your scanner may not work correctly if you use a USB cable other than

the one supplied by EPSON or if you connect your scanner through more

than one hub.

8Turn on the power switch on the side of the scanner.

The scanner turns on and the ] Start button flashes green. It stops flashing

and turns green when the scanner is ready.

Scanner Basics

Your First Scan

The ] Start button on your scanner automatically opens Smart Panel, making it

easy for you to scan your images for many different uses. Here’s how you can use

the ] Start button and Smart Panel to scan photos and save them as files.

1Raise the scanner cover and place your

photo face down on the glass. Make

sure the top right corner of the photo

is aligned with the top right corner

of the scanner.

Then close the cover.

2Press the ] Start button on your scanner.

Note: In Windows XP, you may see a message the first time you press the

] Start button. Select Smart Panel for Scanner, click Always use this

program for this action, then click OK.

EPSON Smart Panel opens on your computer.

3Click the Scan and Save icon.

A progress meter appears on the screen and your document is automatically

scanned. After your document is scanned, the Verify Assistant opens.

4Click Next to continue.

5When you see the following screen, select a location and file type for your

scanned image, then click Save.

Perfection 3170 Photo scanner

(cover includes transparency unit)

CD-ROM with

EPSON Scan driver,

software, and

electronic manuals

USB cable

Slide holder

Power cord and AC adapter

Adobe® Photoshop®

Elements 2.0 CD-ROM

Transparency holder

Negative holder

Automatic document feeder Paper support

Spare paper path guide

ADF document mat

IMPORTANT!

Leave the sticker in place until

you are instructed to remove it

Click Install

Remove sticker

AC adapter

Power cord

Select a file format

pec

y t

e pat

the folder where you

want to save your

scanned image

Click Save

Start Here

12345678-00 Printed in Singapore XXX

4XXXXXXRev.0

1-B BK

4XXXXXXRev.0

1-B Y

4XXXXXXRev.0

1-B M

4XXXXXXRev.0

1-B C

4XXXXXXRev.0

1-B BK2

Scanning Film

The scanner cover has a built-in transparency unit (TPU). To scan negative

strips, slides, or transparencies, you need to remove the document mat from the

cover and insert the film in a holder.

The scanner comes with 3 different film holders: one for negative strips, one for

slides, and one for medium-format transparencies.

1Make sure the transparency unit cable is connected to

the scanner (see step 6 in “Connect the Scanner”).

2Lift the scanner cover all the way up and slide

the reflective document mat up and off of the

scanner cover.

3Follow the instructions for the type of film you are scanning:

If you are scanning negative strips or medium-format transparencies, slide

the film into the corresponding holder, with the film’s shiny side facing down.

If you are scanning slides, place the holder on the scanner first, then place

the slides in the holder, as shown at the bottom of the sheet.

4Place the film holder on the scanner as shown. Make sure the white triangle

on the holder points to the upper-right corner of the scanner.

Note: Make sure the narrow calibration space at the top of the film holder is

uncovered to ensure an accurate scan.

If you are scanning slides, place the holder on the scanner. Then place the

slides in the holder.

5Close the scanner cover.

Scanning a Multi-Page

Document

The optional automatic document feeder (ADF) allows you to automatically load

multi-page documents into your scanner. Make sure the scanner is turned off,

then follow these steps to install the ADF on the scanner and load a stack of

pages:

1Unplug the transparency unit cable from the back of the scanner.

2Remove the scanner cover by lifting it straight up:

3Make sure the scanner glass is clean. Insert the hinges on the ADF into the

square holes at the back of the scanner, then lower the ADF.

4Plug the ADF connector cable into the round port at the back of the scanner.

5Attach the paper support.

6To load a document in the feeder, first pull out the lower paper support and

slide out the edge guide.

7Then insert your document face up with the first page on top. Make sure the

top edge is facing into the ADF, then slide the document all the way in.

Note: After you install the ADF, you can still scan by placing a photo or document

directly on the scanner glass. Lift up the ADF, place the photo on the glass, then

place the ADF document mat on top of the photo. Lower the ADF before you

scan.

Using the Scanner Buttons

The scanner buttons make scanning easy. Just place your document face down

on the scanner and press the button for the type of scan you want. Smart Panel

automatically opens and scans your documents. Then follow the easy on-screen

instructions to finish your task.

Note: If you are using Mac OS X, make sure Smart Panel is installed in a Mac

OS X environment, not Classic mode. Otherwise, Classic mode may start when

you press a scanner button.

Problems?

First, check the ] Start button light on the scanner.

If your problem is listed here, try these suggestions.

Here’s where to look for more answers:

•Double-click the Perfection 3170P Reference Guide icon on your desktop. (If

you didn’t install it, insert the scanner software CD-ROM in the CD-ROM or

DVD drive. At the Custom Installation screen, select Scanner Reference

Guide, then click Install.

•On-screen Help for Smart Panel and EPSON Scan: Click the Help button

or question mark that appears on the screen when you’re using these

programs.

Safety Instructions

Read all these instructions and save them for later reference. Follow all warnings and instructions

marked on the scanner.

Caution: Be sure the AC power cord meets the relevant local safety standards.

Place the scanner close enough to the computer for the interface cable to reach it easily. Do not

place or store the scanner or the AC adapter outdoors, near excessive dirt or dust, water, heat

sources, or in locations subject to shocks, vibrations, high temperature or humidity, direct sunlight,

strong light sources, or rapid changes in temperature or humidity. Do not use with wet hands.

Place the scanner and the AC adapter near an electrical outlet where the power cord can be

easily unplugged.

Power supply cords should be placed to avoid abrasions, cuts, fraying, crimping, and kinking.

Do not place objects on top of power-supply cords and do not allow the AC adapter or power-

supply cords to be stepped on or run over. Be particularly careful to keep all power-supply cords

straight at the ends and the points where they enter and leave the AC adapter.

Use only the AC adapter model A221B/E that comes with your scanner. Using any other adapter

could cause fire, electrical shock, or injury.

The AC adapter is designed for use with the scanner with which it was included. Do not attempt

to use it with other electronic devices unless specified.

Use only the type of power source indicated on the AC adapter’s label, and always supply power

directly from a standard domestic electrical outlet with the AC power cord that meets the relevant

local safety standards.

Avoid using outlets on the same circuit as photocopiers or air control systems that regularly switch

on and off.

If you use an extension cord with the scanner, make sure the total ampere rating of the devices

plugged into the extension cord does not exceed the cord’s ampere rating. Also, make sure the

total ampere rating of all devices plugged into the electrical outlet does not exceed the electrical

outlet’s ampere rating. Do not place multiple loads on the electrical outlet.

Never disassemble, modify, or attempt to repair the AC adapter, power cord, scanner, and option

by yourself except as specifically explained in the scanner’s guides.

Do not insert objects into any opening as they may touch dangerous voltage points or short out

parts. Beware of electrical shock hazards.

Unplug the scanner and the AC adapter, and refer servicing to qualified service personnel under

the following conditions:

The power cord or plug is damaged; liquid has entered the scanner or the AC adapter; the scanner

or the AC adapter has been dropped or the case damaged; the scanner or the AC adapter does

not operate normally or exhibits a distinct change in performance. (Do not adjust controls that

are not covered by the operating instructions.)

Unplug the scanner and the AC adapter before cleaning. Clean with a damp cloth only. Do not

use liquid or aerosol cleaners.

If you are not going to use the scanner for a long period, be sure to unplug the AC adapter from

the electrical outlet.

For US and Canadian users: To reduce the risk of fire, use only the included power cord or a

6 to 10 foot long UL-approved type SPT-2 or heavier, 2 x 18 AWG cord with a 125 V 10 A plug

and 125 V 7 A connector.

If your AC adapter is equipped with a polarized alternating-current line plug (a plug having one

blade wider than the other) and a polarized power inlet, you must insert the plug into a power

outlet in a specific way. This is a safety feature. If you are unable to insert the plug properly, try

reversing the plug. If this fails again, contact an electrician to replace your outlet. Be sure to use

only the polarized power cord that comes with the scanner.

For United Kingdom, Singapore, and Hong Kong users: Replace fuses only with fuses of the

correct size and rating.

For United Kingdom users: The following safety information applies to the AC adapter.

Warning: Refer to the rating plate for the voltage and check that the appliance

voltage corresponds to the supply voltage.

Important: The wires in the mains lead fitted to this appliance are coloured in accordance with

following code: Blue - Neutral, Brown - Live

If you have to fit a plug:

As the colours of the mains lead of the appliance may not match the coloured markings used to

identify the terminals in a plug, please observe the following:

The blue wire must be connected to the terminal in the plug marked with the letter N.

The brown wire must be connected to the terminal in the plug marked with the letter L.

If damage occurs to the plug, replace the cord set or consult a qualified electrician.

form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written

permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for use with this

EPSON scanner. EPSON is not responsible for any use of this information as applied to other scanners. Neither

SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third parties for

damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or

abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)

failure to strictly comply with SEIKO EPSON CORPORATION's operating and maintenance instructions.

SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any options

or any consumable products other than those designated as Original EPSON Products or EPSON Approved Products

by SEIKO EPSON CORPORATION. SEIKO EPSON CORPORATION shall not be held liable for any damage resulting

from electromagnetic interference that occurs from the use of any interface cables other than those designated as

EPSON Approved Products by SEIKO EPSON CORPORATION. EPSON is a registered trademark of SEIKO EPSON

CORPORATION. Microsoft and Windows are registered trademarks of Microsoft Corporation. Macintosh is a

registered trademark of Apple Computer, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of

their respective owners. EPSON disclaims any and all rights in those marks.

35-mm negative or film strips Medium-format transparencies: Slide the film

into the holder as shown. Then lower the

cover and press the tab to lock it in place.

Cover tab

Calibration space

Flashing green Warming up or scanning.

Green Ready to scan.

Flashing red Make sure the transportation lock is unlocked (see

section 3).

Try restarting your computer and turning the

scanner off and then on again.

If the red light is still flashing, contact your dealer or

EPSON.

Off Make sure the scanner is connected to your

computer and the power switch is turned on.

The New Hardware Wizard

appears on your screen. Click Cancel and follow the steps in “Install the

Software” on the other side of this sheet.

Disconnect the scanner before installing the

software.

The scanner makes a

grinding noise when it is

turned on.

Make sure the transportation lock is unlocked (see

section 3).

You see an error message

when you try to scan, or the

scanner doesn’t scan.

Make sure the scanner is connected to your

computer and plugged into a power source.

Uninstall and reinstall EPSON Scan.

Scan to

Web Copy

Scan to

E-mail Start

Epson perfection 3170 Installation guide

Epson perfection 3170 Installation guide

Epson perfection 3170 Installation guide

Related papers

Other documents