Astria Fireplaces DRT4240/45-OLD Instruction Sheet
- Category
- Fireplaces
- Type
- Instruction Sheet
This manual is also suitable for
Instructions for Field Service Upgrade
on AltairDLX / DRT 4200 (units with
lights only) Direct-Vent Gas Fireplaces
Applicable Models Listed Below*
P/N 900915-01 Rev. A 11/2018
For more information, visit IHP.US.com
INSTALLATION INSTRUCTIONS
1. Turn off the unit, let it cool at room temperature, remove the barrier
and remove glass door.
2. From inside unit, remove the four (4) inner screws at location shown
in Figure 1, if present (screws may not be installed).
3. Remove three (3) front fastening screws (see Figure 2).
4. Lift the rear of the baffle to clear the screws from which it hangs, and
pull forward (see Figure 3).
KIT CONTENTS
1 ea. Base, Flue Restrictor
1 ea. Flap, Restrictor
1 ea. Plate, Restrictor Extension
2 ea. Assembly, Door Latch
2 ea. Screw, HWH 10-16X1/2 Typ AB Blk
4 ea. Screw, 10-16x.38 HWH "B" Blk
1 ea. Pilot Hood
1 ea. Rear Baffle Block-off Plate (40" models only)
1 ea. Baffle 40 DVA, w/Lights
1 ea. Baffle 45 DVA, w/Lights
1 ea. Installation Instructions
TOOLS REQUIRED
5/16" Socket Screw
Pliers
4mm Allen Wrench
Small Flat Screwdriver
FIELD SERVICE UPGRADES SHALL ONLY BE COMPLETED BY A
QUALIFIED SERVICE TECHNICIAN
CAUTION
SHARP EDGES - WATCH YOUR
FINGERS
Wear gloves to guard against any
sharp metal edges.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Field Service Upgrade Kit
Cat. No. F3772 40" Models
Cat. No. F3773 45" Models
* Affected Fireplace Models
Astria
®
Models Superior
®
Models
AltairDLX40DEN-B DRT4240DEN-B
AltairDLX40DEP-B DRT4240DEP-B
AltairDLX45TEN-B DRT4245TEN-B
AltairDLX45TEP-B DRT4245TEP-B
Remove Four (4) Screws
Remove Three (3) Screws
Figure 1
Figure 2
Figure 3
Lift Rear of Baffle Off Screw and
Pull Forward to Remove.
Screw
From Left and
Right Bulb Cover
2
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 5
Figure 6
Figure 7
INSTRUCTIONS FOR INSTALLING LIGHTS BAFFLE
1. Install light glass holder from old baffle onto new baffle.
2. Install the lintel from the old baffle onto the new baffle by sliding lintel
onto front edge of new baffle and bending tabs down (see Figures 4
and 6).
3. Remove the two screws on the top triangle shape cover (see Figure
9) and screw the rear tab of the new baffle in the same location.
4. Screw the baffle to the front using 3 screws shown in Figure 2.
Latches
Screws
2 Latches
Firebox
Floor
IF UNIT IS TOP-VENTED, FIELD SERVICE IS COMPLETE.
NOTE: It is important to ensure proper log and or media placement
per the manual when installing these units. Verify pilot flame is not
obstructed.
Reference manual to test fire unit and verify proper operation.
IF THE UNIT IS REAR-VENTING, CONTINUE ON TO
INSTRUCTIONS ON NEXT PAGE.
5. Remove the lintel from the old baffle by bending tabs up (see Figure
4), and sliding the Lintel off of the front edge of the baffle.
6. Remove light glass holders from old baffle by removing four screws
(see Figure 5).
7. Change the pilot hood -
Step 4a (see Page 4)
Step 4b (see Page 4)
8. NOTE: Skip this step If the unit was installed without flue Restrictor.
Replace flue restrictor with the new restrictor assembly. Discard the
existing restrictor. See Figures 11 and 12.
9. Replace the existing door latches with the new ones provided in the
kit by removing the latches screws from the firebox floor. Discard the
old latches (see Figure 7).
Figure 4
3
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
Figure 8 - Block-Off Plate
Figure 9
Figure 10 - Lights Baffle
Use the following instructions when installing the provided Block-Off
Plate on Rear-Venting Fireplaces that do not have any vertical rise
or elbows installed only.
INSTALLATION INSTRUCTIONS FOR BLOCK-OFF PANEL
1. Locate the supplied Baffle Block-Off Plate (see Figure 8).
2. Locate attachment holes for Block-Off Plate installation in new baffle
as shown in Figure 9.
3. Install the bent Baffle Block-Off Plate as shown in Figure 8 using
the (2) screws provided in kit.
*
Figure 11 - Vent restrictor installation, Top vent
Figure 12 - Vent restrictor installation, Rear vent
Installation in top vent. Put flap (and wing if installed)
directed toward the rear of unit.
Installation in rear vent. Install so flap (and wing if installed)
will stay closed
To Termination
Flap Must Move
Up Freely
Exhaust From Inside Fireplace
To Termination
Flap Must
Move Up
Freely
Exhaust
From
Inside
Fireplace
Use screws to attach
the new lights baffle
Screw baffle block off here
4
Printed in U.S.A. © 2018 Innovative Hearth Products
P/N 900915-01 Rev. A 11/2018
Innovative Hearth Products (IHP) reserves the right to make changes at any time, without
notice, in design, materials, specifications, prices and also to discontinue colors, styles and
products. Consult your local distributor for fireplace code information.
1769 East Lawrence Street • Russellville, AL 35654
NOTE: It is important to ensure proper log and or media placement
per the manual when installing these units. Verify pilot flame is not ob-
structed.
Reference manual to test fire unit and verify proper operation.
If all other steps of Baffle replacement and door brackets
have been completed, field service for rear venting unit
is complete with the installation of the Block-Off Plate.
4a. Remove pilot head by pulling up firmly, discard it and
verify proper pilot gas setting. For Natural gas units the
orifice should be turned counter-clockwise. For Propane
(LP) gas units the orifice should turned clockwise. Some
pilot orifices require a small flat standard screwdriver and
some require a 4mm allen type wrench to rotate the orifice
in the pilot cavity. See Figure 13a and 13b.
4b. Install new pilot head provided in this kit by pressing down
firmly until a click is heard. Verify that the pilot head is
properly installed by lightly pulling up and verifying the
spring is still installed. See Figure 13a.
4c. After Pilot hood replacement, Discard the old pilot hood,
light the pilot and verify the ignition is correct per the
installation instructions.
Figure 13
Pilot Hood
Pilot Hood
Cavity
A
B
Figure 14 - Pilot Hood
Pilot Hood
Pilot Hood Removed
-
1
-
2
-
3
-
4
Astria Fireplaces DRT4240/45-OLD Instruction Sheet
- Category
- Fireplaces
- Type
- Instruction Sheet
- This manual is also suitable for
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Kozyheat Princeton Owner's manual
-
-
-
-
-
-
-
Ambiance Fireplaces Intrigue Owner's manual
-
Ambiance Fireplaces Intrigue Owner's manual
-
