K-EDGE BRAZE-ON CLAMP ADAPTER (SOLD SEPERATELY - K13-030-34.9)
K-EDGE BRAZE-ON ADAPTER
"BACK-BOLT"
1x M5 x 12mm FHCS
"NON-DRIVE / INSIDE" CAGE HALF
"LOCKING-BOLTS"
2x M4 x 12mm SHCS
"DRIVESIDE / OUTSIDE" CAGE HALF
"CAGE-BOLTS"
3x M2.5 x 12mm SHCS
K13-050 - K-EDGE CX SINGLE-RING GUIDE W/ O.L.S.- TECHNICAL INSTRUCTIONS
DESCRIPTION OF PARTS
OR
0.45 N-m (+/- 0.09 N-m)
EQUALLY TORQUE
TO 2.00 N-m (+/- 0.20 N-m)
4.00 N-m (+/- 0.50 N-m)
+5°
-5°
A
A
DESCRIPTION OF O.L.S. - 'OPPOSING-LOCK-SYSTEM'
OPENING FOR 3mm HEX
TOOL ACCESSIBILITY
B
SECTION A-A
VIEW OF MECHANISM
DETAIL B
OF MECHANISM
"BACK-BOLT"
SETS
HORIZONTAL DISTANCE FOR
CHAINLINE ALIGNMENT
"LOCKING-BOLTS"
PRODUCE AN
'OPPOSING'
FORCE ONTO THE BACK-BOLT
-
LOCKING
THE CAGE INTO DESIRED
POSITION
K-EDGE BRAZE-ON CLAMP ADAPTER
M5 FLAT WASHER
M5 x
20mm
SHCS
IF YOUR FRAME
DOES NOT
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE RADIUS WASHER
M5 FLAT WASHER
M5 x
20mm
SHCS
MOUNTING OPTIONS
IF YOUR FRAME
DOES
HAVE A BRAZE-ON,
USE SETUP BELOW
K-EDGE BRAZE-ON
ADAPTER
BACK-BOLT
APPLY BLUE
LOCTITE ON
THREADS
d
(BOTTOM VIEW)
d
K-EDGE BRAZE-ON
ADAPTER
INNER CAGE
LOCKING-BOLTS
*APPLY BLUE LOCTITE*
**
LIGHTLY TIGHTEN
**
(a)
DETAIL (a)
**
ATTENTION
**
ENSURE
NO
CONTACT
BETWEEN THE
ADAPTER AND FRAME
(b)
DETAIL (b)
**
ATTENTION
**
ENSURE
NO
CONTACT
BETWEEN THE
ADAPTER AND FRAME
BRAZE-ON RECOMMENDATIONS:
38T - 42T > UPPER MOUNTING HOLE
•
42T - 46T > LOWER MOUNTING HOLE
•
UPPER
MOUNTING HOLE
LOWER
MOUNTING HOLE
2.1
DETAIL 2.1
SCALE 1 : 2
ANGLE CAGE TO NEUTRAL
(0-DEGREE) POSITION
1
SET "BACK-BOLT" DISTANCE
MOUNT TO BE USED:
K-EDGE BRAZE-ON CLAMP ADAPTER -
d = 2.9mm
•
BRAZE-ON ON FRAME -
d = 4.9mm
•
2
INSTALL NON-DRIVE CAGE
AND SET INITIAL ANGLE
INSTALLATION STEPS: 1 > 2 > 3
(a)
OR
(b)
>
OPTION (a)
INCLUDED
OPTION (b)
SOLD SEPERATELY
3(a) 3(b)
INSTALL ONTO FRAME PER
YOUR
"MOUNTING OPTION"
(TRUE BRAZE-ON SHOWN)
INSTALL ONTO FRAME PER
YOUR
"MOUNTING OPTION"
(CLAMP ADAPTER SHOWN)
OR
PROCEED TO NEXT PAGE FOR
SETUP AND ADJUSTMENT
NOTE:
K-EDGE BRAZE-ON ADAPTER
M5 MOUNTING HOLES
THE K-EDGE BRAZE-ON
ADAPTER HAS 2x M5 MOUNTING
HOLES AVAILABLE FOR
VARIABLE CHAIN RING SIZES.
DEPENDING ON YOUR
CONFIGURATION, YOU MAY
NEED TO USE EITHER THE
UPPER OR LOWER MOUNTING
HOLE.
CLAMP RECOMMENDATIONS:
ALL SIZES USE LOWER MOUNTING HOLE
•
DEPENDENT ON FRAME DESIGNS
•
REQUIRED TOOLS:
2mm HEX KEY ('L' OR 'T' SHAPE)
•
3mm HEX KEY ('L' OR 'T' SHAPE)
•
4mm HEX KEY ('L' OR 'T' SHAPE)
•
**IF THERE
IS
FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY**
**IF THERE
IS
FRAME CONTACT, CONTACT K-EDGE IMMEDIATELY**
THE ABOVE DISTANCES ARE RECOMMENDATIONS TO SAVE YOU
TIME DURING THE ADJUSTMENT STEPS. IF THESE DISTANCES
ARE NOT CORRECT, PLEASE MAKE NOTE AND NOTIFY K-EDGE.
5.1
DETAIL 5.1
4.1
DETAIL 4.1
CURVATURE AT
BOTTOM OF CAGE
RADIUS OF RING
6.1
d
d
DETAIL 6.1
INNER CAGE FACE
OUTER CAGE FACE
CHAIN RING
(CHAIN NOT SHOWN)
DRIVESIDE / OUTER
CAGE
3x M2.5 x 12mm SHCS
*APPLY BLUE LOCTITE*
0.88 N-m (+/- 0.09 N-m)
4.2
DETAIL 4.2
ENSURE THESE TWO FACES
ON INNER CAGE ARE 'IN-LINE'
WITH TEETH OF CHAINRING
7.1
7.2
AFTER ADJUSTMENT IS COMPLETE,
EQUALLY
TORQUE
'LOCKING-BOLTS' TO
2.00 N-m (+/-
0.20 N-m),
AND CONFIRM ALIGNMENT
+5°
-5°
DETAIL 7.1
ENSURE BOTTOM OF
CAGE IS FLUSH WITH
BOTTOM OF CHAIN
ENSURE REAR OF CAGE
ASSEMBLY IS
0.5-1.0mm
FROM TOP OF CHAIN
RING TEETH
+3°
-3°
DETAIL 7.2
EQUAL DISTANCE
BETWEEN CHAIN
AND CAGE FACES
NO CONTACT
BETWEEN CHAIN
AND CAGE FACES
38T w/ BRAZE-ON CLAMP ADAPTER SHOWN
46T w/ TRUE BRAZE-ON SHOWN
SETUP AND ADJUSTMENT: 4 > 5 > 6 > 7 > 8
5
INSTALL OUTER CAGE
4
ADJUST FOR HEIGHT
ADJUST FOR CHAINLINE DISTANCE
6
CHECK FOR FUNCTION AND BOLT TORQUE
8
ADJUST FOR PITCH AND YAW
7
SET THE HEIGHT OF THE ADAPTER:
'APPROXIMATELY' ALIGN THE CURVATURE AT BOTTOM OF
1.
THE CAGE TO THE RADIUS OF THE RING (SEE DIAGRAM 4.1)
SET 'APPROXIMATE' TOP-DOWN ALIGNMENT OF CAGE TO
2.
THE CHAIN RING (SEE DIAGRAM 4.2)
FINAL ADJUSTMENTS WILL BE MADE AT STEPS #6 - #7
ADJUST FOR CHAINLINE:
SET LATERAL ADJUSTMENT VIA THE COMBINATION OF THE
1.
'LOCKING-BOLTS' AND' BACK-BOLT'
ENSURE EQUAL SPACING BETWEEN THE CHAIN AND THE
2.
INSIDE OF THE INBOARD / OUTBOARD CAGE FACES. (SEE
DIAGRAM 6.1)
d = DISTANCE BETWEEN CAGE FACE AND CHAIN / CHAIN-RING
ADJUST FOR PITCH:
SET PITCH ANGLE VIA THE COMBINATION OF THE 'LOCKING-
1.
BOLTS' AND' BACK-BOLT' MOVEMENT
(MAX ANGLE = +/- 5
)
CONFIRM BOTTOM OF CAGE ASSEMBLY IS FLUSH WITH
•
THE BOTTOM OF THE CHAIN. (SEE DIAGRAM 7.1)
CONFIRM REAR OF CAGE ASSEMBLY IS
0.5-1.0mm
FROM
•
TOP OF CHAIN RING TEETH. (SEE DIAGRAM 7.1)
ADJUST FOR YAW:
SET YAW ANGLE VIA THE COMBINATION OF THE 'LOCKING-
2.
BOLTS' AND' BACK-BOLT' MOVEMENT
(
MAX ANGLE = +/- 3
)
CONFIRM FRONT OF CAGE ASSEMBLY IS EQUIDISTANT
•
FROM CHAIN AND CAGE FACES. (SEE DIAGRAM 7.2)
CONFIRM REAR OF CAGE ASSEMBLY IS NOT CONTACTING
•
CHAIN. (SEE DIAGRAM 7.2)
**IF APPLICABLE, INSTALL CHAIN PRIOR TO CAGE INSTALL**
STEPS TO CHECK FOR FUNCTION AND INSTALLATION INTEGRITY:
SHIFT TO BOTH ENDS OF THE CASSETTE AND CONFIRM
NO CONTACT
BETWEEN CHAIN AND THE CAGE
1.
IF
THERE IS CONTACT
•
CONFIRM STEPS #5-#7
•
IF
THERE IS NO CONTACT
•
PROCEED TO NEXT STEP
•
** CAUTION **
DERAILING TO THE OUTSIDE CAN/WILL DAMAGE THE FINISH OF THE CRANKSET -
USE WITH DISCRETION
BACK-PEDAL AND MANUALLY DERAIL THE CHAIN FROM THE BOTTOM - TO THE INSIDE AND/OR
**OUTSIDE**
OF THE RING
2.
IF
CHAIN SNAGS AND PREVENTS MOVEMENT OF THE CRANKSET
•
CHECK FOR HEIGHT (STEP #4)
•
CHECK FOR PITCH (STEP #7.1)
•
IF
CHAIN IS 'LIFTED' ABOVE THE TEETH AND ALLOWS BACK-PEDALING OF THE CRANKSET
•
PROCEED TO NEXT STEP
•
PEDAL FORWARD TO 'RE-ENGAGE THE' CHAIN ONTO THE CHAIN RING
3.
IF
CHAIN SLIPS BETWEEN THE CAGE AND THE CHAIN RING
•
CONFIRM STEPS #6-#7
•
IF
CHAIN RE-ENGAGES ONTO CHAIN RING AND FORWARD MOVEMENT IS RESTORED
•
PROCEED TO NEXT STEP
•
RE-CHECK THE FOLLOWING:
4.
-CAGE PITCH ANGLE
-CAGE YAW ANGLE
-REAR CAGE DISTANCE TO TOP OF TEETH
IF
MOVEMENT WAS DETECTED (i.e. NO LONGER IN PROPER ADJUSTMENT)
•
REPEAT STEPS #4-#7
•
RE-TORQUE ALL BOLTS IN THE SYSTEM REPEAT FUNCTION TEST
•
IF
NO MOVEMENT IS DETECTED
•
FUNCTION CHECK IS COMPLETE.
•
BOLT TORQUE SPECIFICATIONS:
CLAMP MOUNTING BOLT = 2.00 N-m (+/- 0.20 N-m)
•
BRAZE-ON MOUNTING BOLT = 4.00 N-m (+/- 0.50 N-m)
•
BACK-BOLT = N/A
•
LOCKING-BOLTS = 2.00 N-m (+/- 0.20 N-m)
•
DRIVESIDE CAGE BOLTS (M2.5 SHCS) = 0.45 N-m (+/- 0.09 N-m)
•
K-EDGE CX SINGLE-RING CHAIN GUIDE SPECIFICATIONS:
CHAIN RING SIZE CAPACITY = 38T - 46T
•
CHAINLINE DISTANCE = 45.5mm (+/- 2.50mm)
•
BRAZE-ON MOUNTING BOLT DISTANCE TO BB-AXIS = 133mm (+/-10mm)
•
CHAIN = 11SPD
•
NARROW-WIDE CHAIN RING COMPATIBILITY = YES
•
DESIGN FEATURES:
FEATURES OF THE K-EDGE CX SINGLE-RING CHAIN GUIDE:
MAXIMUM ADJUSTABILITY TO FIT VARYING FRAME GEOMETRY
•
MINIMAL CONTACT DURING NORMAL OPERATION
•
MINIMAL WEIGHT GAIN
•
ENHANCED 'TOP-SIDE' CHAIN GUIDANCE
•
ENHANCED 'TOP-OF-CHAIN CLEARANCE' TO ACCOUNT FOR F.O.D. (FOREIGN OBJECT DEBRIS)
•
ENHANCED MUD-CLEARANCE
•
ENHANCED '
BACK-PEDAL
DERAILMENT PROTECTION'
•
EASE OF INSTALLATION AND ADJUSTMENT
•
SLIM, SLEEK, AND APPEALING DESIGN
•
K13-050 - K-EDGE CX SINGLE RING GUIDE W/ O.L.S.- TECHNICAL INSTRUCTIONS
SUPPORT / CONTACT:
IF PROBLEM(S) STILL PERSIST AFTER TROUBLESHOOTING,
PLEASE CONTACT K-EDGE SUPPORT FOR FURTHER
ASSISTANCE AT [email protected] IMMEDIATELY. PLEASE
BE SURE TO INCLUDE YOUR FULL NAME, PHONE NUMBER,
AND K-EDGE PRODUCT PURCHASED.
/
