AEG GYE01016EE User manual

Type
User manual

This manual is also suitable for

CONTENTS
1. SAFETY INFORMATION...........................................................................................3
2. SAFETY INSTRUCTIONS.......................................................................................... 5
3. INSTALLATION......................................................................................................... 6
4. CONTROL PANEL.....................................................................................................7
5. USAGE........................................................................................................................8
6. CARE AND CLEANING............................................................................................ 8
7. MAINTENANCE........................................................................................................ 9
8. TROUBLESHOOTING.............................................................................................11
9. TECHNICAL DATA..................................................................................................13
FOR PERFECT RESULTS
Thank you for choosing this AEG product. We have created it to give you
impeccable performance for many years, with innovative technologies that help
make life simpler features you might not find on ordinary appliances. Please
spend a few minutes reading to get the very best from it.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.aeg.com/webselfservice
Register your product for better service:
www.registeraeg.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.aeg.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
ZZZDHJFRP
1. SAFETY INFORMATION
Before the installation and use of the appliance,
carefully read the supplied instructions. The
manufacturer is not responsible if an incorrect
installation and use causes injuries and damages. Always
keep the instructions with the appliance for future
reference.
1.1 Children and vulnerable people safety
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge only if they have been given
supervision or instruction concerning using the
appliance in a safe way and understanding the
hazards involved.
Do not let children play with the appliance.
Keep all packaging items away from children.
If the appliance has a child safety device, or a function
that limits the temperature permanently, we
recommend you activate it.
Cleaning and user maintenance shall not be made by
children without supervision.
Children of less than 8 years should be kept away
unless continuously supervised.
1.2 General safety
It is most important that this instruction book should
be retained with the appliance for future reference.
Should the appliance be sold or transferred to another
owner, or should you move to another house and
leave the appliance, always ensure that the book is
supplied with the appliance in order that the new
owner can get to know the functioning of the
appliance and the relevant warnings.
(1*/,6+
Correct functioning of your appliance does not only
depend on product quality, but on correct installation
by a qualified professional.
Never remove or damage stickers, warning labels or
nameplates attached to the appliance.
A qualified technician carrying out the installation is
obliged to observe applicable national standards and
regulations concerning connection to the water
distribution system and the electric network. The
manufacturer is not responsible for any unprofessional
or incorrect installation.
Check that the specifications written on the
appliance’s identification plate are the same as those
of the electrical power supply.
This appliance is manufactured and tested in
accordance with valid regulations.
The operating water pressure (minimum and
maximum) must be between 0,1 bar (0,01 MPa) and 10
bar (1,0 MPa).
To prevent scalds while using the water heater, always
check the water temperature and adjust as needed
before use.
In the case of faults, a peak temperature of up
to 99 °C may briefly occur in the system.
1.3 Special information
When permanently connected to the power supply
using a dedicated junction box, the appliance must be
able to be isolated from the mains power supply by an
isolator that disconnects all poles with at least 3 mm
contact separation.
The power cable may only be replaced (for example if
damaged) by a qualified contractor authorised by the
manufacturer, using an original spare part.
Secure the appliance as described in chapter "3.3".
Observe the maximum permissible pressure (see
chapter "9.4").
ZZZDHJFRP
Drain the appliance as described in chapter "7.2".
The appliance is pressurised. During the heat-up
process, expansion water will drip from the safety
valve.
Regularly activate the safety valve to prevent it from
becoming blocked, e.g. by limescale deposits.
Install a type-examination tested safety valve in the
cold water supply line. Depending on the supply
pressure, you may also need a pressure reducing
valve.
Size the drain pipe so that water can drain off
unimpeded when the safety valve is fully opened.
Fit the drain pipe of the safety valve with a constant
downward slope and in a room free from the risk of
frost.
The safety valve drain must remain open to the
atmosphere.
2. SAFETY INSTRUCTIONS
2.1 Installation
Obey the installation instruction
supplied with the appliance.
Remove all the Packaging items.
Do not install or use a damaged
appliance.
Before first time starting up, check the
appliance for any damage incurred
during transport.
Never remove or damage stickers,
warning labels or nameplates
attached to the appliance.
2.2 Water Connection
Make sure not to cause damage to
the water hoses.
The appliance is to be connected to
the water mains using suitable hose-
sets.
Before you connect the appliance to
new pipes or pipes not used for a
long time, let the water flow until it is
clean.
The first time you use the appliance,
make sure that there is no leakage.
2.3 Electrical Connection
WARNING!
Risk of fire and electrical
shock.
To carry out all electrical
connection and installation
work in accordance with
relevant regulations.
The appliance must be earthed.
Make sure that the electrical
information on the rating plate agrees
with the power supply. If not, contact
our Authorised Service Centre or an
electrician.
Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
Do not use multi-plug adapters and
extension cables.
Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
(1*/,6+
Service Centre or an electrician to
change a damaged mains cable.
The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
An appropriate socket or
adapter for the Schuko plug
should be used if necessary.
The water heater needs to
be connected to the
protective conductor.
2.4 CE designation
The CE designation shows that the
appliance meets all essential
requirements according to the:
Low Voltage Directive.
Electromagnetic Compatibility
Directive.
RoHS directive.
3. INSTALLATION
3.1 Standard delivery
The following are delivered with the
appliance:
Wall mounting bracket.
Two locking ring fitting G ½ x 15
(delivered only with GYE01016UE +
GYE01516UE).
3.2 Placement
The sealed unvented
(pressurised) appliance is
only suitable for undersink
installation. The appliance is
intended for heating cold
water and to supply one or
several draw-off points.
The appliance may only be installed with
pressure taps in conjunction with a type-
examination tested safety valve.
The type-examination tested safety valve
protects the appliance against
unacceptable excess pressure.
WARNING!
Do not install the appliance
in the following places:
Outdoors.
Areas that are cold and
freezing, the freezing
water may damage the
internal tank and pipes.
Where water discharge is
not possible.
Ensure that the appliance is
freely accessible for
maintenance work.
Always install the appliance vertically and
near the draw-off point.
3.3 Appliance installation
The appliance is designed for installation
on a solid wall. Ensure the wall offers
adequate load bearing capacity.
Always install the appliance
vertically in a room free from
the risk of frost and near the
draw-off point.
1. Mark out the holes to be drilled on
the wall.
2. Drill the holes and insert suitable rawl
plugs.
3. Secure the wall mounting bracket
using suitable screws.
ZZZDHJFRP
4. Hang the appliance on the wall
mounting bracket.
3.4 Safety valve installation
The water heaters are designed for a
maximum rated pressure of 1 MPa.
According to EN 60335-2-21 the safety
valve must prevent the water pressure to
exceed the maximum rated pressure of
the water heater from more than 0.1
MPa.
A type-examination tested safety valve is
required.
1. Install the safety valve in the cold
water supply line of the appliance.
2. Size the drain pipe so that water can
drain off unimpeded when the safety
valve is fully opened.
3. Fit the drain pipe of the safety valve
with a constant downward slope and
in a room free from the risk of frost.
WARNING!
The safety valve drain must
remain open to the
atmosphere.
If the supply pressure is
>0.48 MPa, install a pressure
reducing valve upstream of
the safety valve in the cold
water supply line.
3.5 Water connection
Carry out all water connection and only
install pressure taps in conjunction with a
safety valve accordance with regulations.
Match up the colour coding on the water
connections of the tap and the
appliance:
R.h. side blue = "Cold water inlet"
L.h. side red = "Hot water outlet"
Ensure that the water
connections are not kinked
during installation. Prevent
any tensioning during
installation.
4. CONTROL PANEL
1
2
1
Temperature selector knob.
2
Heat-up indicator lamp.
Depending on the system, the actual
temperatures may vary from the set
value.
* = Cold. On this setting, the appliance is
protected from frost. The tap, water lines
and safety valve are not protected.
MAX = Highest selectable temperature.
(1*/,6+
5. USAGE
5.1 Filling
This sealed unvented
(pressurised) appliance is
intended for heating
domestic hot water. The
appliance can supply one or
more draw-off points.
Once the water heater has been
installed:
1. Open the water source valve.
2. Open the hot tap.
When the water starts to run through it
with constant flow, then the water heater
will be full.
3. Close the hot taps
4. Make sure there are no leaks in the
installation.
5. Check that the safety valve is working
correctly.
WARNING!
Do not connect the water
heater to the main power
supply without being sure
that it is full of water,
otherwise the heating
element may be damaged.
5.2 Adjusting water
temperature
WARNING!
During operation, the tap
and safety valve can reach
temperatures in excess of 60
°C. There is a risk of scalding
at outlet temperatures in
excess of 43 °C.
You can set any required temperature of
outlet water at the temperature selector,
it's steplessly variable from 11°C (frost
protection) to MAX.
The temperature selector
should only be removed by a
qualified contractor.
Subject to season, varying
cold water temperatures can
result in different maximum
mixed water and outlet
volumes.
5.3 Operating
After the temperature had been adjusted
to the desired value, the heating element
will heat up the water inside the tank
until the water temperature reaches to
the setting value, then heater will go to
OFF state.
After the water inside the tank gets
cooler, and the temperature will be lower
than the setting temperature, the
heating process will start working again
and heat the water inside the tank. The
operation will repeat continuously in
automatic manner as long as the
electrical source connected to the water
heater.
6. CARE AND CLEANING
WARNING!
All the repair and
maintenance must be
carried out by customer
service authorized
technicians.
Regularly activate the safety
valve to prevent it from
becoming blocked, e.g. by
limescale deposits.
Appliance malfunctions should be
repaired immediately to keep the
performance of it.
ZZZDHJFRP
A clean soft cloth or wet sponge can be
used for the cleaning.
Dis-solvent products are not allowed for
the cleaning.
7. MAINTENANCE
WARNING!
Before any work on the
appliance, disconnect all
poles of the appliance from
the power supply.
The water heater requires no special
maintenance. The anode rod helps
protect the tank against corrosion.
Depending on the water condition, the
magnesium anode rod may need to be
changed every 2 years. Galvanic and
electrolytic corrosion can damage the
tank if the anode rod worn out. Rusty
water is usually an indication of a worn
out anode rod. If rusty water is present,
you must call the authorized
professionals immediately in order to
examine anode rod and replace if
necessary.
There are some points to check when
you make the required maintenance for
this appliance.
7.1 Checking the safety valve
Check the function of the safety valve
regularly.
7.2 Draining the appliance
WARNING!
Hot water may escape
during the draining process.
Drain the appliance via its connectors.
7.3 Opening the appliance
1. Pull off the temperature selector and
the limiting ring.
2. Remove the 4 screws from the
casing.
3. Open the appliance cover by
pivoting the cover upwards and then
removing it.
4. Remove the upper insulation semi-
shell if required.
(1*/,6+
7.4 Setting the temperature
limit
1
2
3
4
1
Limiting ring
2
38 °C
3
49 °C
4
65 °C
Placing the limiting ring behind the
temperature selector allows you to limit
the setting range of the temperature
selector to a specific maximum
temperature.
1. Turn the temperature selector to
zero (fully clockwise to "*").
2. Pull off the temperature selector and
the limiting ring.
3. Push the limiting ring with the
required maximum setting onto the
appliance cover.
4. Install the temperature selector set to
zero ("*").
7.5 Activate high limit safety
cut-out
1. Open the appliance.
2. Pull off the adaptor.
3. Press the reset button on the high
limit safety cut-out.
4. Fit the adaptor.
5. Close the appliance cover.
6. Fit the limiting ring and temperature
selector.
12
1
Reset button, high limit safety cut-
out
2
Adaptor
7.6 Removing the flanged
immersion heater and
temperature controller / high
limit safety cutout
12
1
Combined temperature controller /
high limit safety cut-out.
2
Flanged immersion heater.
1. Remove the combined temperature
controller / high limit safety cut-out
from the flanged immersion heater.
2. Remove the flanged immersion
heater.
ZZZDHJFRP
7.7 Removing the protective
anode
1
1
Protective anode
Remove the protective anode.
7.8 Fitting the flanged
immersion heater and
temperature controller / high
limit safety cutout
1. Insert the flanged immersion heater
into the cylinder aperture well as far
as it will go.
2. Push the combined temperature
controller / high limit safety cut-out
into the flanged immersion heater as
far as it will go.
3. Align the flanged immersion heater
and the combined temperature
controller / high limit safety cut-out in
accordance with the diagram.
8. TROUBLESHOOTING
Certain problems are due to lack of
simple maintenance or oversights, which
can be solved easily without calling the
service technicians, before contacting
the local service centre please carry out
the check listed below.
(1*/,6+

Problem Cause Remedy
The appliance does not sup-
ply hot water.
The temperature selector is
set to "*".
Switch the appliance ON by
turning the temperature se-
lector.
No power at the appliance.
Check the plug / fuses in the
fuse box.
The high limit safety cut-out
has tripped.
Remedy the cause of the
fault. If necessary, replace
the combined temperature
controller / high limit safety
cut-out. Make the high limit
safety cut-out operational by
pressing the reset button on
the high limit safety cut-out
(see chapter 7.5).
The controller is faulty.
Replace the combined tem-
perature controller / high
limit safety cut-out.
The flanged immersion heat-
er is faulty.
Replace the flanged immer-
sion heater.
Water can only be drawn at
a reduced rate.
The aerator in the tap is
scaled up or dirty.
Descale / replace the aera-
tor.
Loud boiling noises inside
the appliance.
The appliance is scaled up.
Have the appliance descaled
by a qualified contractor.
Water drips from the safety
valve after heat-up.
The safety valve is scaled up
or dirty.
Switch the appliance off. De-
pressurise the appliance by
disconnecting it from the
power and water supply.
Have the safety valve
checked by a qualified con-
tractor.
Water leaks.
Improperly sealed, hot or
cold water source connec-
tions.
Tighten threaded connec-
tions.
If you cannot remedy the
fault, notify your qualified
contractor. To facilitate and
speed up your enquiry,
please provide the following
numbers from the type
plate :
PNC (9 digits)
SN (8 digits)
ZZZDHJFRP
9. TECHNICAL DATA
9.1 Specification
A
80
mm
100
mm
F
C
G
H
E
2
1
GYE01016UE GYE01516UE GYE01016EE GYE01516EE
H Height 454 476 430 452
C Width 280 320 280 320
A Depth 270 318 270 318
G
Top clear-
ance
50.5 47 26.5 23
F Height 320 342 320 342
E
Horizontal
hole spac-
ing
140 200 140 200
Inlet & Out-
let Pipe
Size Ø15 Ø15
G ½ A Male
thread
G ½ A Male
thread
All dimensions in mm
This specifications depend
on the model type
1. Compression fittings (delivered only
with GYE01516UE & GYE01016UE).
2. Electric cable (available with Schuko
plug only for GYE01516EE &
GYE01016EE).
9.2 Wiring diagram
1/N/PE ~ 220-240 V
(1*/,6+

L
AB
NPE
12
9.3 Details on energy
consumption
Product data complies with EU
regulations relating to the Directive on
the ecodesign of energy related
products (ErP).
GYE01016UE GYE01516UE GYE01016EE GYE01516EE
Load profile XXS XXS XXS XXS
Energy efficien-
cy class
AAAA
Energy conver-
sion efficiency
(%)
   
Daily power
consumption
(kWh)
2.42 2.42 2.42 2.42
Annual power
consumption
(kWh)
515 515 515 515
Default temper-
ature setting
(°C)
55 55 55 55
Sound power
level (dB(A))
15 15 15 15
Off-peak peri-
ods possible
No No No No
9.4 Data table
GYE01016UE GYE01516UE GYE01016EE GYE01516EE
Hydraulic data
Nominal capaci-
ty (L)
10 15 10 15
ZZZDHJFRP
GYE01016UE GYE01516UE GYE01016EE GYE01516EE
Mixed water vol-
ume at 40 °C (L)
15.3 23 15.3 23
Electrical data
Rated voltage
(V)
220 / 230 / 240
Rated output
(kW)
1.4 / 1.5 / 1.6
Rated current
(A)
6.2 / 6.5 / 6.8
MCB/fuse rating
(A)
10
Phases 1/N/PE
Frequency (Hz) 50/60
Application limits
Temperature
setting range
(°C)
30-65
Max. permissi-
ble pressure
(MPa)
1
Min. water inlet
pressure (MPa)
0.1
Max. water inlet
pressure (MPa)
1
Max. flow rate
(L/min)
10
Energy data
Standby energy
consumption/24
h at 65 °C (kWh)
0.48 0.49 0.48 0.49
Energy efficien-
cy class
A
Versions
IP rating IP24 D
Type of installa-
tion
Undersink
(1*/,6+

GYE01016UE GYE01516UE GYE01016EE GYE01516EE
Type Sealed unvented
Internal cylinder
material
Steel, enamelled
Thermal insula-
tion material
EPS
Casing material PS
Colour White
Dimensions
Depth (mm) 270 318 270 318
Height (mm) 454 476 430 452
Width (mm) 280 320 280 320
Weights
Weight (kg) 7.1 8.6 7.1 8.6
10. ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol .
Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to
recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol
with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
ZZZDHJFRP
www.aeg.com/shop

  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156

AEG GYE01016EE User manual

Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI