Page is loading ...
CONTENTS
1. SAFETY INFORMATION
....................................................................................3
2. SAFETY INSTRUCTIONS..................................................................................5
3. INSTALLATION.................................................................................................. 6
4. USER INTERFACE............................................................................................ 7
5. USAGE............................................................................................................... 8
6. FEATURES.........................................................................................................8
7. CARE AND CLEANING......................................................................................8
8. MAINTENANCE..................................................................................................9
9. WHAT TO DO IF.................................................................................................9
10. TECHNICAL DATA.........................................................................................10
WE’RE THINKING OF YOU
Thank you for purchasing an Electrolux appliance. You’ve chosen a product that
brings with it decades of professional experience and innovation. Ingenious and
stylish, it has been designed with you in mind. So whenever you use it, you can
be safe in the knowledge that you’ll get great results every time.
Welcome to Electrolux.
Visit our website for:
Get usage advice, brochures, trouble shooter, service information:
www.electrolux.com/webselfservice
Register your product for better service:
www.registerelectrolux.com
Buy Accessories, Consumables and Original spare parts for your appliance:
www.electrolux.com/shop
CUSTOMER CARE AND SERVICE
Always use original spare parts.
When contacting our Authorised Service Centre, ensure that you have the
following data available: Model, PNC, Serial Number.
The information can be found on the rating plate.
Warning / Caution-Safety information
General information and tips
Environmental information
Subject to change without notice.
www.electrolux.com2
1. SAFETY INFORMATION
Before the installation and use of the appliance, carefully
read the supplied instructions. The manufacturer is not
responsible if an incorrect installation and use causes
injuries and damages. Always keep the instructions with
the appliance for future reference.
1.1 Children and vulnerable people safety
• This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge only if they have been given
supervision or instruction concerning using the
appliance in a safe way and understanding the
hazards involved.
• Do not let children play with the appliance.
• Keep all packaging items away from children.
• If the appliance has a child safety device, or a function
that limits the temperature permanently, we
recommend you activate it.
• Cleaning and user maintenance shall not be made by
children without supervision.
• Children of less than 8 years should be kept away
unless continuously supervised.
1.2 General safety
• It is most important that this instruction book should be
retained with the appliance for future reference.
Should the appliance be sold or transferred to another
owner, or should you move to another house and
leave the appliance, always ensure that the book is
supplied with the appliance in order that the new
owner can get to know the functioning of the appliance
and the relevant warnings.
• Correct functioning of your appliance does not only
depend on product quality, but on correct installation
by a qualified professional.
ENGLISH 3
• Never remove or damage stickers, warning labels or
nameplates attached to the appliance.
• A qualified technician carrying out the installation is
obliged to observe applicable national standards and
regulations concerning connection to the water
distribution system and the electric network. The
manufacturer is not responsible for any unprofessional
or incorrect installation.
• Check that the specifications written on the
appliance’s identification plate are the same as those
of the electrical power supply.
• This appliance is manufactured and tested in
accordance with valid regulations.
• To prevent scalds, While using the water heater,
always check the water temperature and adjust as
needed before use.
1.3 Special Information
• This appliance is intended to be used to store, heat
and provide drinking water and has no negative
impact on inlet water.
• The power cable may only be replaced (for example if
damaged) by a qualified contractor authorised by the
manufacturer, using an original spare part.
• The electrical installation must have an isolation
device which lets you disconnect the appliance from
the mains at all poles. The isolation device must have
a contact opening width of minimum 3 mm.
• Before any work on the appliance, disconnect all poles
of the appliance from the power supply.
• The water heater must be installed with the safety
valve, which has a non return valve (supplied with the
water heater).
• No hydraulic accessory needed to be installed
between the safety unit and the cold water inlet tube
service valve (plug valve, non-return valve, etc).
www.electrolux.com4
• Do not connect the water heater to the main power
supply without being sure that it is full of water,
otherwise the heating element may be damaged.
• Drain the appliance as described in chapter
"Maintenance-drain the appliance".
• Regularly activate the safety valve to prevent it from
becoming blocked, e.g. by limescale deposits.
• All the repair and maintenance must be carried out by
customer service authorized technicians.
2. SAFETY INSTRUCTIONS
2.1 Installation
• Obey the installation instruction
supplied with the appliance.
• Remove all the Packaging items.
• Do not install or use a damaged
appliance.
• Before first time starting up, check the
appliance for any damage incurred
during transport.
• Never remove or damage stickers,
warning labels or nameplates
attached to the appliance.
2.2 Water Connection
• Make sure not to cause damage to
the water hoses.
•
The appliance is to be connected to
the water mains using suitable hose-
sets.
• Before you connect the appliance to
new pipes or pipes not used for a long
time, let the water flow until it is clean.
• The first time you use the appliance,
make sure that there is no leakage.
2.3 Electrical Connection
WARNING!
Risk of fire and electrical
shock.
To carry out all electrical
connection and installation
work in accordance with
relevant regulations.
• The appliance must be earthed.
•
Make sure that the electrical
information on the rating plate agrees
with the power supply. If not, contact
our Authorised Service Centre or an
electrician.
• Make sure the appliance is installed
correctly. Loose and incorrect
electricity mains cable or plug (if
applicable) can make the terminal
become too hot.
• Do not use multi-plug adapters and
extension cables.
• Make sure not to cause damage to
the mains plug (if applicable) or to the
mains cable. Contact our Authorised
Service Centre or an electrician to
change a damaged mains cable.
• The electrical installation must have
an isolation device which lets you
disconnect the appliance from the
mains at all poles. The isolation
device must have a contact opening
width of minimum 3 mm.
2.4 CE designation
The CE designation shows that the
appliance meets all essential
requirements according to the:
• Anti-legionella
• Low Voltage Directive.
• Electromagnetic Compatibility
Directive.
• RoHS directive.
ENGLISH 5
3. INSTALLATION
3.1 Accessories
The appliance is supplied with the basic
equipment required for their installation
and Usage, such as:
•
Safety valve.
This accessory is inside the packaging.
3.2 Placement
Both the wall on which the
water heater is to be
installed and the fixing wall
plugs and screws must hold
the weight of the appliance
full of water. If the wall is
very thin, back plates must
be used on the other side of
the wall. drill two holes on
the wall with size of 14mm
diameters and depth is
90mm.
90
mm
Ø =14 mm
260 mm
WARNING!
Do not install the appliance
in the following places:
• Outdoors.
•
Areas that are cold and freezing, the
freezing water may damage the
internal tank and pipes.
• Close to the ground.
• Where water discharge is not
possible.
The water heater can be placed
anywhere in the house. Nevertheless we
recommend placing it as near as
possible to the hot water tap, in order to
prevent temperature loss in the pipes.
The appliance can be installed in all
bathroom sections except marked zones.
3.3 Hydraulic Installation
• Before starting connection to the
water distribution system, it is very
important to clean inlet pipes properly
to prevent metal or other particles
from getting into the heater body.
•
Leave a minimum space of 40 cm
under the pipe outlet of the water
heater, to be able to gain access to
the electrical parts and to make
maintenance and repairing easier.
• If plastic pipes are being used, and in
order to carry out the installation
conditions, the pressure and
temperature conditions they are going
to undergo have to be taken into
account. A maximum pressure of 9
bars and maximum temperature of
70ºC, in normal conditions, or of
100ºC in abnormal conditions if the
safety thermostat switches off.
• In case of copper piping, connection
to the heater pipes must be made with
nonconductive sleeves to avoid
corrosion of piping (by direct contact
of iron and copper). Brass sleeve is
not permitted.
The water heater MUST be
installed with the safety
valve, which has a non-
return valve (supplied with
the water heater).
www.electrolux.com6
No hydraulic accessory
needed to be installed
between the safety unit and
the cold water inlet tube
service valve (plug valve,
non-return valve, etc).
• The pressure relief opening of the
safety unit can be connected to a
drain pipe, with a diameter that is at
least the same as the water heater
connection pipe, with a continuous
inclination and open to atmosphere.
Pressure relief valve works
only when the pressure
inside the heater tank
increases above
7+1bar ,relief will be in a
continuous water drops form
that comes out from
pressure relief opening.
WARNING!
If the main network pressure
is more than 5 bars, it is
OBLIGATORY to install a 3
or 4 bar pressure regulator
in the mains connection of
the house.
3.4 Electrical Installation
The heater may only be connected with a
single phase to alternating voltage 230V.
Connect the appliance to the power
source with a 1.5mm² cable for heating
element power 1200W or 1500W and
2mm² cable for heating element power
2000W.
Distance from appliance
location to the power supply
should be not more 5m long.
The cable earthing
conductor must be
connected to the earth or an
earthing wire must be led to
a prepared connector
indicated with the symbol
. This connection is
necessary due to safety, It
must be checked that the
electrical installation of the
premises or house is
equipped with an “EARTH”
line.
WARNING!
It is strictly forbidden to
tamper with or replace parts
(including the power supply
cable), as only the Technical
Support Services are
allowed to do it.
4. USER INTERFACE
1
2
3
1
Thermometer
2
Plastic panel
3
Heating Indicator Lamp
ENGLISH 7
5. USAGE
5.1 Filling
This sealed unvented
(pressurised) appliance is
intended for heating
domestic hot water. The
appliance can supply one or
more draw-off points.
Once the water heater has been
installed:
1. Open the water source valve.
2. Open the hot tap.
When the water starts to run through it
with constant flow, then the water heater
will be full.
3. Close the hot taps
4. Make sure there are no leaks in the
installation.
5. Connect the appliance to the power
supply.
WARNING!
Do not connect the water
heater to the main power
supply without being sure
that it is full of water,
otherwise the heating
element may be damaged.
6. FEATURES
6.1 Long life tank
The tank is equipped with magnesium
anode to protect the tank against
corrosion.
6.2 Safety
The appliance is protected from over-
heating over-pressure with three types of
safety:
•
Thermal fuse
• Relief valve
• Non return valve
6.3 HD
polyurethane insulation
foam
High-density polyurethane foam injected
between the inner tank and the outer
shell.
• To reduce power consumption.
• Keep heat loss controlled.
The material of the foam was chosen
carefully to give the best performance for
a long life.
7. CARE AND CLEANING
WARNING!
All the repair and
maintenance must be
carried out by customer
service authorized
technicians.
Regularly activate the safety
valve to prevent it from
becoming blocked, e.g. by
limescale deposits.
Appliance malfunctions should be
repaired immediately to keep the
performance of it.
A clean soft cloth or wet sponge can be
used for the cleaning.
Dis-solvent products are not allowed for
the cleaning.
www.electrolux.com8
8. MAINTENANCE
WARNING!
Before any work on the
appliance, disconnect all
poles of the appliance from
the power supply.
The water heater requires no special
maintenance. The anode rod helps
protect the tank against corrosion.
Depending on the water condition, the
magnesium anode rod may need to be
changed every 2 years. Galvanic and
electrolytic corrosion can damage the
tank if the anode rod worn out. Rusty
water is usually an indication of a worn
out anode rod. If rusty water is present,
you must call the authorized
professionals immediately for it to
examine anode rod and replace if
necessary.
The thermal fuse which based in the
thermostat, cuts both phases and leaves
the water heater without voltage; protect
the appliance from excessive electric due
to a possible thermostat fault, If this case
occurred, you must call the authorized
professionals for it to be repaired.
N
L
E
T
1
T2
T3
T4
1
234
1
Connected to main electric supply
main switch
2
Cable
3
Thermostat base
4
Heating indicator lamp
The manufacture reserves
the right to modify the
characteristics and
specifications of its products,
without prior notice.
8.1 Draining the appliance
WARNING!
Hot water may escape
during the draining process.
To drain the water from the electrical
storage water heater:
1. Disconnect the water heater from
power source.
2. Close the inlet water source from
service valve.
3. Disassemble inlet water hose from
cold water inlet pipe of the appliance.
4. Open the hot water tape the water
will drain off the inlet pipe.
9. WHAT TO DO IF
Certain problems are due to lack of simple maintenance or oversights, which can be solved
easily without calling the service technicians, before contacting the local service centre
please carry out the check listed below.
ENGLISH 9
Problem Possible causes Solution
Water leaks
Improperly sealed, hot or
cold water source connec‐
tions.
Tighten threaded connec‐
tions.
No hot water No power to heater.
Turn on electrical switch,
Check for blown fuses or
tripped breaker.
Insufficient hot water
Cold water mix fast with
appliance stored hot water,
high water source pres‐
sure.
Close the inlet water serv‐
ice valve(or the pressure
regulator) partially until the
problem disappear.
Wrong piping connections. Correct piping.
Wasted hot water.
Review and reduce hot
water consumption.
Long runs of exposed pipe. Insulate piping.
Hot water piping on out‐
side wall.
Insulate piping.
High operation cost (power
consumption)
Wrong piping connections. Correct piping.
Wasted hot water.
Review and reduce hot
water consumption.
Long runs of exposed pipe. Insulate piping.
Hot water piping on out‐
side wall.
Insulate piping.
Leaking Taps. Repair leaking taps.
Dripping from safety valve
High water source pres‐
sure.
Install a 3 or 4 bar pres‐
sure regulator valve in the
mains connection of the
house.
Brown (rusty) water from
outlet
Brown or rusty water indi‐
cates a worn out anode
rod
Call authorized professio‐
nals for anode rod exami‐
nation and replace it if nec‐
essary
10. TECHNICAL DATA
10.1 Details on energy
consumption
Product data complies with EU
regulations relating to the Directive on
the ecodesign of energy related products
(ErP).
www.electrolux.com10
EYE030S1WE EYE050S1WE EYE080S1WE EYE100S1WE
Load profile S M M
M
Energy efficien‐
cy class
D D D D
Energy conver‐
sion efficiency
[%]
29.1
34.4 33.2 33.0
Daily power
consumption
[kWh]
3.1
7.08
7.4
7.46
Annual power
consumption
[kWh]
634
1495
1548
1558
Default temper‐
ature settings
[°C]
60 60 60 64
Sound power
level [dB (A)]
15 15 15 15
Off-peak peri‐
ods possible
No No No No
10.2 Data table
EYE030S1WE EYE050S1WE EYE080S1WE EYE100S1WE
Model 30 50 80 100
V40 [l] -
68.2 101.2 124.6
Storage capacity [l]
30
- - -
Power [Watt] 1200 1200 1500 1500
Voltage [Volt] 230 V 230 V 230 V 230 V
Frequency [Hz] 50 - 60 50 - 60 50 - 60 50 - 60
Operating Pressure
[(bar) MPa]
(7) 0.7 (7) 0.7 (7) 0.7 (7) 0.7
Safety Valve pres‐
sure [bar]
7+1 7+1 7+1 7+1
Dimen‐
sions
[mm]
A 575 730 990 1140
B
445 595 855 1005
IP grade IPX1 IPX1 IPX1 IPX1
ENGLISH 11
EYE030S1WE EYE050S1WE EYE080S1WE EYE100S1WE
Inlet &
Outlet
Pipe size
diameter
[inch]
Male
thread
G ½ G ½ G ½ G ½
Min. water inlet
pressure [MPa]
0.1 0.1 0.1 0.1
Heat up time (Delta
T 45°C)
1h:0min 1h:55min 2h:40min 3h:40min
7
9
10
12
13
14
475 mm
440 mm
260
mm
5
6
4
3
2
1
B
A
8
11
1
Fixing bracket
2
Plastic support
3
Safety & Non return valve
4
Flexible hoses
5
Service valve
6
Cold water inlet pipe
7
Polyurethane insulation
8
Thermometer
9
Water tank
10
Hot water outlet pipe
11
Heating element
12
Magnesium anode
13
Plastic panel
14
Thermostat
11. ENVIRONMENTAL CONCERNS
Recycle the materials with the symbol
. Put the packaging in applicable
containers to recycle it. Help protect the
environment and human health and to
www.electrolux.com12
recycle waste of electrical and electronic
appliances. Do not dispose appliances
marked with the symbol with the
household waste. Return the product to
your local recycling facility or contact
your municipal office.
ENGLISH 13
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
Page is loading ...
www.electrolux.com/shop
PHEWA0881
/
