JAI CV-A10CL-A70CL Operating instructions

1019E-1007

CV-S3500E

NTSC/PAL selectable

Progressive scan color video camera

Document Version: Ver.1.0

CV-S3500E_Ver.1.0_Sept2010

User's Manual

CV-S3500E

- 2 -

Notice

The material contained in this manual consists of information that is proprietary to JAI Ltd., Japan

and may only be used by the purchasers of the product. JAI Ltd., Japan makes no warranty for the

use of its product and assumes no responsibility for any errors which may appear or for damages

resulting from the use of the information contained herein. JAI Ltd., Japan reserves the right to

make changes without notice.

Company and product names mentioned in this manual are trademarks or registered trademarks of

their respective owners.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE compliance

As defined by the Directive 2004/108/EC of the European Parliament and of the Council, EMC

(Electromagnetic compatibility), JAI Ltd., Japan declares that CV-S3500E complies with the

following provisions applying to its standards.

EN 61000-6-3 (Generic emission standard part 1)

EN 61000-6-2 (immunity)

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Warning

Changes or modifications to this unit not expressly approved by the party responsible for FCC

compliance could void the user’s authority to operate the equipment.

CV-S3500E

Supplement

The following statement is related to the regulation on “ Measures for the Administration

of the control of Pollution by Electronic Information Products “ , known as “ China RoHS “.

The table shows contained Hazardous Substances in this camera.

mark shows that the environment-friendly use period of contained Hazardous

Substances is 15 years.

嶷勣廣吭並㍻

嗤蕎嗤墾麗嵎賜圷殆兆各式根楚燕

功象嶄鯖繁酎慌才忽佚連恢匍何〆窮徨佚連恢瞳麟半陣崙砿尖一隈〇



云恢瞳ゞ嗤蕎



嗤

墾麗嵎賜圷殆兆各式根楚燕〃泌和



桟隠聞喘豚㍉

窮徨佚連恢瞳嶄根嗤議嗤蕎嗤墾麗嵎賜圷殆壓屎械聞喘議訳周和音氏窟伏翌

亶賜融延、窮徨佚連恢瞳喘薩聞喘乎窮徨佚連恢瞳音氏斤桟廠夛撹冢嶷麟半

賜斤児繁附、夏恢夛撹冢嶷鱒墾議豚㍉。

方忖仝15々葎豚㍉15定。

CV-S3500E

- 3 -

Table of Contents

1. General ............................................................................................................... - 5 -

2. Main Features ....................................................................................................... - 5 -

3. Composition ......................................................................................................... - 5 -

4. Locations ............................................................................................................ - 6 -

4.1. Locations and functions .................................................................................. - 6 -

4.2. LED indication .............................................................................................. - 7 -

4.2.1 Power indication ..................................................................................... - 7 -

4.2.2 LED (LINK) ............................................................................................ - 7 -

4.2.3 LED (ACT) ............................................................................................. - 7 -

5. Pin Assignment ...................................................................................................... - 8 -

5.1. D-SUB 9-pin multi-connector (DC-in/Video/RS-232C) ................................................ - 8 -

5.2. RJ-45 Ethernet Connector ................................................................................. - 8 -

Note: When PoE is used, Cat5 or better cable should be used. .......................................... - 8 -

5.3. Auto iris lens connector ................................................................................... - 8 -

6. Connections ......................................................................................................... - 9 -

6.1. Power ........................................................................................................ - 9 -

6.2. Video output (NTSC or PAL) ............................................................................. - 9 -

6.3. Ethernet connection ...................................................................................... - 9 -

6.3.1 MAC address and IP address ....................................................................... - 9 -

6.3.2 Automatic acquisition of RTC time (SNTP) .................................................... - 10 -

6.3.3 User access ......................................................................................... - 10 -

6.3.4 Setup menu ......................................................................................... - 10 -

6.3.5 Image format through Ethernet interface .................................................... - 10 -

7. Camera configuration – OSD (On Screen Display) .......................................................... - 11 -

7.1. Top menu ................................................................................................. - 11 -

7.2. CAMERA menu tree ..................................................................................... - 13 -

7.3. SET UP menu tree ....................................................................................... - 14 -

7.4. Descriptions of camera functions ...................................................................... - 15 -

8. Camera Configuration – RS-232C .............................................................................. - 16 -

8.1. RS-232SC Interface ...................................................................................... - 16 -

8.2. Download and install CV-S3500E camera control tool ............................................ - 16 -

8.3. Camera control tool ..................................................................................... - 17 -

9. Camera configuration and how to use web browser ...................................................... - 21 -

9.1. Initial settings .............................................................................................. - 21 -

9.1.1 Set IP address manually .......................................................................... - 21 -

9.1.2 Obtain an IP address automatically. ........................................................... - 23 -

9.2. TOP menu .................................................................................................. - 23 -

9.3. View Camera top menu ................................................................................. - 24 -

9.4. SetUp top menu .......................................................................................... - 25 -

9.4.1 SetUp-D Zoom ...................................................................................... - 25 -

9.4.2 SetUp-Camera ...................................................................................... - 25 -

9.4.3 SetUp-capture ...................................................................................... - 26 -

9.4.4 SetUp-Network ..................................................................................... - 26 -

9.4.5 SetUp-Time ........................................................................................ - 27 -

9.4.6 SetUp - Reset ....................................................................................... - 27 -

9.4.7 SetUp-User .......................................................................................... - 28 -

10. External Appearance and Dimensions ..................................................................... - 29 -

11. Specifications .................................................................................................. - 30 -

11.1. Spectral sensitivity .................................................................................... - 30 -

11.2. Specifications table .................................................................................... - 31 -

Appendix .............................................................................................................. - 33 -

1. Precautions .................................................................................................. - 33 -

2. Typical Sensor Characteristics ........................................................................... - 33 -

3. Caution when mounting a lens on the camera ........................................................ - 33 -

4. Exportation .................................................................................................. - 33 -

CV-S3500E

- 4 -

5. References .................................................................................................. - 33 -

Change history ....................................................................................................... - 34 -

User's Record ......................................................................................................... - 35 -

CV-S3500E

- 5 -

1. General

The CV-S3500E is a high resolution camera employing 1/3 inch, 1.25-megapixel progressive scan

CCD.

The CV-S3500E has conventional analog video output, such as composite video and Y/C (luminance

and chrominance) signal. It also provides digital compressed video for both moving and still images.

JPEG still image, Motion JEPG, MPEG4 or H.264 is selectable for digital output. The digital data is

transferred through Ethernet, 100BASE-T or 10BASE-T networking. The power is also provided over

Ethernet (PoE).

The CV-S3500E utilizes a CS mount and includes a C-mount adaptor as an accessory for various C

mount lenses.

The CV-S3500E has an on-screen display for setup, as well as RS-232C control and controls

accessible through Ethernet.

The CV-S3500E is suitable for various applications using NTSC or PAL analog output or as an IP

network camera providing high quality images.

2. Main Features

• 1/3 inch progressive scan Bayer mosaic color CCD with 1.25 million effective pixels

• 1280 x960 ( 15 fps ) and 960 x 720 ( 30 fps ) sensor scanning modes

• Dual encoding for JPEG and MPEG4/H.264

• Motion JPEG, MPEG4 or H.264 with 640 x 480 resolution image through Ethernet

• NTSC or PAL output converted from 1280 x 960 resolution or 960 x 720 resolution

• Analog Composite and YC outputs for NTSC or PAL signal

• On-screen menu set up

• Auto iris connector built in (DC or video)

• Auto shutter function

• Gamma selection of 1.0, 0.6 or 0.45

• 2x digital zoom function

• Power over Ethernet or DC 10.8V to DC 26.4 through D-sub 9-pin connector

• RS-232C interface or Ethernet for camera settings

3. Composition

Camera main unit x 1

C Mount adapter x 1

Auto Iris Lens Plug (4pin) x 1

Hexagonal wrench x 1

CV-S3500E

- 6 -

4. Locations

4.1. Locations and functions

①

Lens mount

CS Mount (note1)

②

Flange back adjustment

Screws for flange back adjustment

③

1/4-20 UNC

Camera mount hole

④

Lens connector

For auto iris (DC or Video)

⑤

D-SUB 9 pin connector

For DC+12V,Video out & RS-232C

⑥

LED Power indication

⑦

BNC Composite video output(NTSC or PAL)

⑧

Function keys

For camera configuration

⑨

RJ-45

Ethernet connection (100BASE-T,10BASE-T)

Power over Ethernet

⑩

Holes for RJ-45

Holes for fixing screws of RJ-45 (note 2)

⑪

LED (ACT.)

Network connection (ACT.)

⑫

LED (LINK)

Network connection (LINK)

Fig.1 Locations

Note 1) Use the provided C-mount adapter for C–mount lenses

Note 2) When an RJ-45 cable with thumbscrews is connected to the camera, please do not

excessively tighten screws by using a screwdriver. The RJ-45 receptacle on the

camera might be damaged. For security, the strength to tighten screws is less than

0.147 Newton meter (Nm). Tightening by hand is sufficient in order to achieve this.

①

②

③

④

⑤

⑥

⑦

⑧

②

⑨

⑩

⑪

⑫

③

①

②

CV-S3500E

- 7 -

4.2. LED indication

4.2.1 Power indication

● Green light: Power ON and it is ready to use.

4.2.2 LED (LINK)

● Green light: Connecting with 100BASE-T or 10BASE-T

4.2.3 LED (ACT)

● Orange light: Standby for 100BASE-T connection

 Orange flashing: Communicating in 100BASE-T

Note: In case of 10BASE-T connection, LED does not light.

CV-S3500E

- 8 -

5. Pin Assignment

5.1. D-SUB 9-pin multi-connector (DC-in/Video/RS-232C)

1

9

6

5

Fig. 2. D-SUB 9-pin connector.

5.2. RJ-45 Ethernet Connector

12345678

Fig. 3. Ethernet connector

Note: When PoE is used, Cat5 or better cable should be used.

5.3. Auto iris lens connector

Type: EIAJ RC-5204

1

3

2

4

Fig.4 Auto iris connector

Pin no.

Signal

Remarks

1

GND

For DC input

2

+12 V DC input

3

GND

4

Video out (VBS)

*1

5

NC

6

Y output

7

C output

8

RS-232C TXD output

9

RS-232C RXD input

*1 : This video output is the same as BNC. Both outputs

cannot be used simultaneously.

Pin No

10BASE-T/100BASE-T

POE

In/out

1 TX+ Alternative A+

2

TX-

Alternative A+

3

RX+

Alternative A-

4

Not used

Alternative B+

5

Not used

Alternative B+

6

RX-

Alternative A-

7

Not used

Alternative B-

8 Not used Alternative B-

Pin No

DC Control ( Passive )

1 D amp -

2

D amp +

3

Drive +

4 Drive -

CV-S3500E

- 9 -

6. Connections

6.1. Power

Power to the CV-S3500E is supplied through the D-SUB 9 pin or the RJ-45 Ethernet interface. The

power consumption of the CV-S3500E is less than 4.2W.

Fig.5 Power supply

The PoE system in the CV-S3500E is Alternative A, which uses data communication lines as power

supply. For connection details, refer to section 5.2.

6.2. Video output (NTSC or PAL)

The CV-S3500E provides composite video and YC video for NTSC or PAL.

BNC output and D-SUB 9-pin output for composite video cannot be used at the same time.

Fig.6 video output

NTSC or PAL output can be selected from the on-screen menu which can be activated by the

function keys on the back of the camera.

6.3. Ethernet connection

The CV-S3500E works as an IP network camera, providing JEPG, MPEG4 or H.264 motion video or

JPEG still pictures. Using a web browser, the camera can be configured for different applications.

Fig.7 Ethernet connection

6.3.1 MAC address and IP address

When connecting to a net work, please check MAC address and IP address.

MAC address Indicated on the bottom of CV-S3500E

IP address Set in accordance with the connected Network

DHCP can acquire appropriate IP address if DHCP function is set to ON.

The following table shows IP address default settings.

Item

Default

IP Address

192.168.30.30

Subnet Mask

255.255.255.0

Default Gateway

0.0.0.0 (not used)

DHCP

OFF

L INK ACT .

POW E R / T R IG

V ID EO OU T

RS - 23 2C/DC IN SYNC /

U P

OD WN

FUNC

100 BASE -TX10 BASE -T /

Pin3 Gnd

Pin4 NTSC or

PAL out

Pin6 Y out

Pin7 C out

D-SUB 9 pin

NTSC or PAL

putput

L INK ACT .

POW E R / T R IG

V ID EO OU T

RS - 23 2C/DC IN SYNC /

U P

OD WN

FUNC

100 BASE -TX10 BASE -T /

Pin1 Gnd

Pin2 +12V

D-SUB 9 pin

POE

(Power over Ethernet)

L INK ACT .

POW E R / T R IG

V I D EO OU T

RS -2 32C/DC IN SYNC /

U P

OD WN

FUN C

100 BASE-TX10 BASE -T /

100BASE-T/10BASE-T

CV-S3500E

- 10 -

6.3.2 Automatic acquisition of RTC time (SNTP)

The CV-S3500E can acquire RTC time through the network. Set IP address of the SNTP time

distribution server.

6.3.3 User access

Access via HTTP can be controlled by registered ID and Password. In the default setting,

they are not registered. Three user levels can be set: administrator, operator and viewer.

6.3.4 Setup menu

Checking network addresses, setting DHCP, and other tasks can be done through function

keys located on the rear of the camera. Please refer to section 7.3 for the setup menu tree.

6.3.5 Image format through Ethernet interface

In the CV-S3500E, the CCD is scanned in two modes, one for 1280 x 960 and the other for

960 x 720. Data can be digitized in two scan modes. This is done by selecting the scan

mode.

Image types available through the Ethernet interface are shown in the following table.

Still/Movie

Format

Scan mode

select

Image size

NTSC/PAL

mode

Frame

rate

Bit rate

Still image

JPEG or

Non-

Compression

1280 x 960

-

960 x 720 960 x 720 - - -

640 x 480

-

Moving

image

Motion JPEG

1280 x 960

1 to 2

fps

Normal/High/Super

960 x 720 960 x 720

MPEG4

1280 x 960

640 x 480

NTSC

15 fps

PAL

12.5 fps

960 x 720 640 x 480 NTSC 30 fps

PAL

25 fps

H.264

1280 x 960

640 x 480

NTSC

15 fps

PAL

12.5 fps

960 x 720 640 x 480 NTSC 30 fps

PAL

25 fps

Note:

1. The performance of motion video through the network depends on the traffic conditions of the

network or graphic performance in the PC.

2. RTP movie transfer uses wideband network bandwidth. Accordingly, there may be limitations

in the network.

3. Using HTTP motion video (1280x960), if the quality is set at “super”, the analog output may be

interrupted.

4. If using RTP JPEG and JPEG still image at the same time, the still image is not activated (no

memory error). If using the JPEG still image, RTP should be set at MPEG4 or H.264.

CV-S3500E

- 11 -

7. Camera configuration – OSD (On Screen Display)

The CV-S3500E camera has an on-screen display in order to set up the camera parameters. The

setup function keys are located on the back of the camera.

Fig.8 Function keys

No.

Name

Function

1

UP key

Select the item as moving upward

2 FUNC key 1.Press and hold to access the on-screen menu

2.Advance through menu items for setting with the UP or DOWN button

3 DOWN key Select the item by moving downwards

7.1. Top menu

When pressing “FUNC” button for a few seconds, 「CAMERA」top menu appears on the screen.

There are three top menus, CAMERA, SET UP and OFF.

Fig.9 CAMERA TOP menu

In order to set “CAMERA”functions, push “FUNC” again. Then, the camera functions described in

section 7.2 appear on the screen.

Push “FUNC” button

CAMERA

Fig.10 To start the set-up of the CAMERA functions

①

②

③

CV-S3500E

- 12 -

If “UP” button is pressed, the menu is changed to “SET UP”.

SET UP

Push “UP” button

Fig.11 Change the menu to “SET UP”

Press “FUNC” button to set up the SET UP functions.

SET UP

Push “FUNC” button

Fig.12 To start the setup of the SET UP functions

In order to set the screen OFF, press “DOWN” button.

Please note that the FUNC button works only to move forward in the menu sequence. It can not be

used to move backwards in the menu sequence.

If “OFF” is shown on screen, pressing the “FUNC” button turns the “Menu” OFF.

CV-S3500E

- 13 -

7.2. CAMERA menu tree

CAMERA

WHITE BALANCE

SHUTTER

AGC

BACK LIGHT

IRIS LEVEL

INTEG.

SHARPNESS

GAMMA

AUTO

ONEPUSH

MANUAL

3200K

4500K

5600K

OFF

1/100

1/250

1/500

1/1000

1/2000

1/4000

1/10000

CCD IRIS (AUTO EXPOSURE)

OFF

MANUAL

12dB MAX

24dB MAX

OFF

PAT 1

PAT 2

PAT 3

DARK ------------- LIGHT

OFF

X2

X4

X6

X8

LOW

HIGH

0.45

0.6

1.0

“FUNC”

Button

“UP” or　”DOWN”

Button

Menu OFF

Fig.13 CAMERA menu tree

CV-S3500E

- 14 -

7.3. SET UP menu tree

The following is the menu tree for SET UP settings. The “FUNC” button can advance through the

main setting items while the “UP and DOWN” buttons can be used to select an appropriate setting.

SET UP

SCAN MODE

H-MIRROR

D-ZOOM

TV-SYSTEM

1280 x 960

960 x 720

OFF

ON

NTSC

PAL

IP_ADR

DHCP

SNTP

192.168.30.30

OFF

ON

OFF

ON

OFF

ON

MAC_ADR

00-01-DF-05-XX-XX

Menu OFF

“FUNC” button

“UP” or “DOWN”

button

SUBNET_MASK

255.255.255.0

Fig.14 SET UP menu tree

CV-S3500E

- 15 -

7.4. Descriptions of camera functions

BACKLIGHT

OFF

PAT1

PAT2

PAT3

Back Light Compensation

This is used with auto iris and/or AGC.

OFF : Average photometry

PAT1,PAT2 and PAT3 use weighting on the total image.

PAT 1 uses the center weighting, PAT 2 uses the center

weighting with less weighting on surrounding areas and PAT3

is weighted in the middle and lower part of the picture (refer

to the following drawings).

PAT 1

PAT ２ PAT ３

Large weighting Small　weighting No weighting

Fig.15 Conceptual drawing of weighting pattern of backlight compensation

INTEG. MAX

OFF

Standard mode

X2 Maximum two times integration

X4

Maximum four times integration

X6

Maximum six times integration

X8 Maximum eight times integration

Note: INTEG. MAX is a high sensitivity mode using longer integration times .

If the objects are moving, the images will be blurred.

INTEG. MAX is a maximum for integration time and this is controlled

automatically. The integration time changes depending on the objects.

D-ZOOM

ON or OFF Digital Zoom

OFF

Factory default

ON

Digital zoom is ON. Two times enlargement for both H and V.

SCAN MODE

Select scanning modes

1280x960 Factory default

CCD scan format is 1280 x 960 @

15 fps frame rate. This

original image is converted to NTSC (30 fps) or PAL (25 fps) or

outputs through Ethernet..

960x720

CCD scan format is 960x720 @ 30 fps frame rate. This original

image is converted to NTSC (30fps) or PAL (25 fps) or outputs

through Ethernet.

CV-S3500E

- 16 -

H-MIRROR

OFF

Factory default

ON For left and right reversed image

8. Camera Configuration – RS-232C

8.1. RS-232SC Interface

Communication speed

38400 bps

Data length

8 bit

Parity

None

Stop bit

1 bit

Flow

None

Type

Asynchronous

8.2. Download and install CV-S3500E camera control tool

CV-S3500E camera control tool can be downloaded at www.jai.com.

Click CV-S3500_ver100_T0112.msi and follow the screen described below.

After the installation is completed, two tools, “CV-S3500E” and “NetCam Search” are

created.

“CV-S3500E” controls the camera functions by RS-232C serial communication.

“NetCam Search” is a tool for Network operation. This is not normally used. It is

for:

 When the IP address set by the DHCP server is needs to be known

 To access the information for MAC_ADR/IP_ADR/Camera Model Name/Firmware

Version

CV-S3500E

- 17 -

8.3. Camera control tool

Connect the CV-S3500E and execute the camera control tool.

The following communication window comes up.

The default setting of port is “AUTO” and the camera control tool automatically searches

for the appropriate port.

Click on the “Camera” tab to configure the camera settings.

CV-S3500E

- 18 -

Click the “Capture” tab and the screen for setting the RTP and HTTP movie image format

is opened. (Set the data volume and picture quality of the transferred image through

Ethernet)

Settings can only be made on fields that are not “grayed out”.

Click “D-zoom” to set up the digital zoom function.

CV-S3500E

- 19 -

Click “Network” to confirm the current network settings.

When the CV-S3500E is connected to the network, the following is the default setting.

If changes are needed, open the PC’s “Control Panel” and clck on “Network connection”,

“Local area network” , “Property”, “Internet protocol /TCP/IP” and “Property”. In the

property window, set the appropriate IP address and subnet mask for the system.

Click “Time” for setting the date and time. If it needs to be automatically synchronized,

set SNTP server ON.

Page is loading ...

JAI CV-A10CL-A70CL Operating instructions

JAI CV-A10CL-A70CL Operating instructions

Related papers

Other documents