Page is loading ...
2008 © Philips Consumer Lifestyle
All rights reserved.
Printed in EU
jpkm_0838/05-1
E2N41BN
1VMN25833 ★★★★★
HDR3700
Need help?
User Manual
See the user manual that came with your Philips Recorder.
Online
Go to www.philips.com/welcome.
About the Time Shift Buffer
Once you turn on the recorder, the selected TV
programme will be stored in a temporary hard disk
storage called Time Shift Buffer. Time Shift Buffer
can store up to 6 hours of programmes temporarily.
Press DISPLAY to display the Time Shift Buffer
information.
Watch TV – Pause live TV
Your Philips Recorder allows you to control the TV
programme. You can PAUSE it as if you were in
control of the broadcast.
A When watching TV programme through this unit’s
tuner, press F (PAUSE).
B Press P (PLAY) again to resume the TV
programme you were watching from where you
have paused.
C To return to live broadcast, press LIVE TV.
Record to Hard Disk or DVD
If you are recording to the Hard Disk, press
HDD
first.
If you are recording to a disc, press
DVD
first, then
insert a recordable disc.
A Select a recording mode using REC MODE.
B Press SOURCE to select digital, analogue or
external input mode, then select the desired
channel to record using PROGRAM + / – or
Alphanumeric keypad.
C Press I (RECORD) to start recording.
D Press C (STOP) to stop the recording.
Using the EPG (On-screen TV guide)
Make sure the digital TV tuning (installation) is
completed.
A In stop mode, press GUIDE.
It shows the list of TV programmes that are
currently broadcast and the next 7 days of TV
programmes.
B Select the TV programme using U \ D \ L \ P,
To watch - press GUIDE to exit.
To set the timer recording - press OK or BLUE to
go to “Timer Programming” menu.
1 EPG menu mode
2 Current date / time
3 Date of selected programme
4 Channel number / name
5 Channel programme
6 Currently Highlighted Programme on EPG
7 Programmes set for the timer recording
: Programmes set for the series link timer recording.
: Once only timer recording.
Start Playback
If you are playing back the titles in Hard Disk, press
HDD first.
If you are playing back the titles in DVD, press DVD
first, then insert a disc.
A For Hard Disk, press TITLE to call up the title list.
For DVD, the title list will automatically appear
when you insert a disc. Otherwise, press TITLE or
DISC MENU.
B Use U \ D \ L \ P to select a desired title, then
press P (PLAY).
C Press C (STOP) to stop playback.
Note
- The Time Shift Buffer will be cleared when you access the functions
listed below (and a warning message will appear when you press
HOME
,
TITLE
or
DISC MENU
): Turn off the power / Start recording /
Edit titles or enter editing menu / Start dubbing / Access Digital Video
input (AV4) / Using any functions in “Disc Editing” or “HDD Settings” /
Perform actions under “Channel” setting (e.g. tuning, sort channels)
- In Time Shift Buffer, when you display the digital programme
information, the on-screen display will be recorded as the part of the
picture.
Note To set the recording time length, press I (RECORD)
repeatedly to extend the recording time in 30-minute
increments, up to 6 hours.
10:10
7:10 10:42
Start time of the
Time Shift Buffer
Status of the Time Shift Buffer Time of current Time Shift Buffer playback
Current time of the Live TV
programme broadcast
The progress of the
Time Shift Buffer
Current point of the playback of
Time Shift Buffer
To pause playback :Press F (PAUSE).
To resume playback :Press P (PLAY).
1
2
4
3
5
6
10:25-11:10 news
12:00-13:00 show
13:00-13:30 musical
13:30-14:35 variety show
19:30-20:00 news
20:00-21:00 drama
Date 18/01/2008
Time 10:30:56
18/01/2008 (Friday)
10:25-11:10 The Montel
1
2
3
4
5 E4
6
7
Daily mode
1 ITV1
2 ITV2
3 ITV3
4 Channel
5 E4
6 More 4
D/W
Series Extended Timer
LIVE TVSOURCE
.@/:
ABC DEF
GHI JKL MNO
PQRS TUV WXYZ
AUDIO
PROGRAM
DISC MENU GUIDE
BACK
DISPLAY
REPLAY
TEXT
SAT. REC
TIMER HOME
SHOWVIEW
HDMI
REC MODE
INFO
CLEAR
SUBTITLE
OK
TITLE
DVDHDD
SKIP
Enjoy
What’s in the box?
Quick Start Guide
RF cable
User Manual
Quick Start Guide
Remote control with two R6
(AA) batteries
Hard Disk/DVD Recorder
Scart cable
Hard Disk/DVD Recorder
Connect
Set up
Enjoy
E2N41BN-PHILIPS.fm Page 1 Tuesday, June 24, 2008 7:52 PM
Basic Connection
A Before Connecting
A Unplug your TV and this unit.
B Select the most suitable connection based on the
type of device you have and your home set up.
For basic connection of recorder to TV, steps B &
C are sufficient. You can also refer to the
accompanying User Manual for other possible
connections.
B Connecting to a TV
with antenna only
A Connect the antenna or cable to the ANTENNA IN
jack of this unit.
B Connect the TV-OUT jack of this unit to the Aerial
jack of your TV. Use the supplied RF cable.
C Connecting Recorder and TV
using the Scart socket
Connect AV1 (TO TV) Scart socket of this unit to
the Scart socket of your TV. Use the supplied
Scart cable.
D Connecting Recorder and TV
using the component video and audio jacks
A Connect the component video cables (red/ blue/
green - not supplied) from the COMPONENT
VIDEO OUTPUT jacks of this unit to the
corresponding component video input jacks
(usually labelled as Y Pb/Cb Pr/Cr or YUV) on
your TV.
B Connect the audio cable (red/white - not supplied)
from the AUDIO OUT (ANALOG L\R) jacks of this
unit to the audio input jacks on your TV.
E Connecting Recorder and TV
using the HDMI jack
HDMI (High-Definition Multimedia Interface) is a
digital interface that allows pure digital video
transmission without the loss of image quality.
Use the HDMI cable (not supplied) for connection.
Connect the HDMI OUT jack of this unit to the HDMI
input jack of TV.
SCART IN
ANTENNA IN
Cable
Signal
Antenna
or
RF cable (not supplied)
RF cable
(supplied)
Scart cable
(supplied)
Note To view video from COMPONENT VIDEO OUTPUT,
please set “Active Video Output” as “Component (Interlace)” or
“Component (Progressive)”.
AUDIO IN
COMPONENT IN
Audio cable
(not supplied)
Component Video Cable
(not supplied)
HDMI OUT
HDMI IN
HDMI cable (not supplied)
F Connecting Recorder and External
Equipment
using the Scart socket
Be sure that all the units are off before making
connections.
Use the Scart cable (not supplied) to connect AV2
(AUX) Scart socket of this unit to the Scart socket of
the external equipment.
G Connecting Recorder and External
Equipment
using the digital audio jack
Use the coaxial cable (not supplied) to connect the
AUDIO OUT (DIGITAL COAXIAL) jack to your digital
audio equipment.
For more advanced connections, refer to the User Manual.
A Finding the Viewing Channel
A Press Q (STANDBY-ON) to turn on the unit.
B Turn on your TV.
• You should see “Initial Setup” menu.
C
In case you don’t see the recorder’s setting menu,
press the Channel Down button on the TVs
remote control repeatedly (or AV SELECT button,
etc) until you see the menu. This is the correct
viewing channel for this unit.
B Start Initial Installation
A Select the desired channel installation using
U \ D. Then press OK.
B After the channel search is finished, “Clock
Setting” will appear. Current time & date will be
automatically updated. In case current time & date
are not updated, you may set them manually.
Once time and date setting is done, proceed to
press BACK U to exit initial setup.
During “Initial Setup”, BACK U will stop the whole setup.
If this occurs, proceed to “HOME” menu to complete
setup.
Your Philips recorder is now ready for use!
Note If the external equipment (e.g. cable box, Canal+
decoder) is connected to AV2, the picture of the external
equipment will be output except during the DVD playback of this
unit. Turn off the external equipment or press DISPLAY to
output the picture from this unit.
Note If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
AV output
socket (Scart)
Scart cable (not supplied)
AV2 (AUX)
COAXIAL
DIGITAL COAXIAL
Coaxial cable
(not supplied)
Digital audio
input jacks
Dolby Digital decoder or
MPEG decoder, etc.
Note Leave the unit in standby for 1 minute after completing
the initial installation and do not unplug the mains power of the
unit. The unit needs this 1 minute to store all the channels. After
1 minute, you can remove the mains power if you need to.
Digital tuning
Digital&Analog Tuning
Analog tuning
TUE
01/01/2008
0:00
( )
Connect Set up
E2N41BN-PHILIPS.fm Page 2 Tuesday, June 24, 2008 7:52 PM
/
