Lexmark T642 - Monochrome Laser Printer User manual

Category
Laser/LED printers
Type
User manual

This manual is also suitable for

www.lexmark.com
4600 MFP Option
Scanner User’s Guide for the
T640, T642, and T644 series printers
April 2006
Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc.,
registered in the United States and/or other countries.
© 2006 Lexmark International, Inc.
All rights reserved.
740 West New Circle Road
Lexington, Kentucky 40550
2
Edition: April 2006
The following paragraph does not apply to any country where such provisions are inconsistent with local law: LEXMARK
INTERNATIONAL, INC., PROVIDES THIS PUBLICATION “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Some states do not allow disclaimer of express or implied warranties in certain transactions; therefore, this
statement may not apply to you.
This publication could include technical inaccuracies or typographical errors. Changes are periodically made to the information herein; these
changes will be incorporated in later editions. Improvements or changes in the products or the programs described may be made at any
time.
Comments about this publication may be addressed to Lexmark International, Inc., Department F95/032-2, 740 West New Circle Road,
Lexington, Kentucky 40550, U.S.A. In the United Kingdom and Eire, send to Lexmark International Ltd., Marketing and Services
Department, Westhorpe House, Westhorpe, Marlow Bucks SL7 3RQ. Lexmark may use or distribute any of the information you supply in
any way it believes appropriate without incurring any obligation to you. To obtain additional copies of publications related to this product,
visit the Lexmark Web site at www.lexmark.com.
References in this publication to products, programs, or services do not imply that the manufacturer intends to make these available in all
countries in which it operates. Any reference to a product, program, or service is not intended to state or imply that only that product,
program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any existing intellectual
property right may be used instead. Evaluation and verification of operation in conjunction with other products, programs, or services, except
those expressly designated by the manufacturer, are the user’s responsibility.
Trademarks
Lexmark, Lexmark with diamond design, MarkVision, and MarkNet are trademarks of Lexmark International, Inc., registered in the United
States and/or other countries.
Operation ReSource and LEXFAX
are service marks of Lexmark International, Inc.
PCL® is a registered trademark of the Hewlett-Packard Company. PCL is Hewlett-Packard Company’s designation of a set of printer
commands (language) and functions included in its printer products. This printer is intended to be compatible with the PCL language. This
means the printer recognizes PCL commands used in various application programs, and that the printer emulates the functions
corresponding to the commands.
Details relating to compatibility are included in the Technical Reference.
Other trademarks are the property of their respective owners.
© 2006 Lexmark International, Inc.
All rights reserved.
UNITED STATES GOVERNMENT RIGHTS
This software and any accompanying documentation provided under this agreement are commercial computer software and documentation
developed exclusively at private expense.
Safety information
Static sensitivity notice
Warning: This symbol identifies static-sensitive parts. Do not touch in the areas near these symbols without first touching the
metal frame of the MFP.
Connect the power cord to a properly grounded electrical outlet that is near the product and easily accessible.
Refer service or repairs, other than those described in the operating instructions, to a professional service person.
This product is designed, tested, and approved to meet strict global safety standards with the use of specific Lexmark
components. The safety features of some parts may not always be obvious. Lexmark is not responsible for the use of
other replacement parts.
CAUTION: Make sure that all external connections (such as Ethernet and telephone system connections) are properly
installed in their marked plug-in ports.
CAUTION: Use only a 26 AWG or larger telecommunications (RJ-11) cord when connecting this product to the public
switched telephone network.
3
Contents
Chapter 1: Learning about the MFP .................................................................................. 7
Basic functions of the scanner .........................................................................................................................7
Automatic document feeder and flatbed ..........................................................................................................7
Understanding the MFP control panel .............................................................................................................8
Using the LCD touch-screen buttons .............................................................................................................13
Menus ............................................................................................................................................................19
Chapter 2: Copying ........................................................................................................... 20
Quick copy .....................................................................................................................................................20
Multiple page copying ....................................................................................................................................20
Using the flatbed ............................................................................................................................................21
Understanding the copy screens and options ................................................................................................21
Copying from one size to another .................................................................................................................. 23
Making transparencies ...................................................................................................................................23
Copying to letterhead ..................................................................................................................................... 23
Copying photographs .....................................................................................................................................23
Making copies using media from a selected tray ...........................................................................................24
Copying mixed-sized media ...........................................................................................................................24
Setting the duplex option ...............................................................................................................................25
Reducing and enlarging copies .....................................................................................................................25
Adjusting copy quality .................................................................................................................................... 25
Setting collation options .................................................................................................................................26
Placing separator sheets between copies .....................................................................................................26
Setting paper saving options ......................................................................................................................... 26
Placing the date and time at the top of each page ........................................................................................ 27
Placing an overlay message on each page ...................................................................................................27
Creating a custom job (job build) ...................................................................................................................27
Canceling a copy job .....................................................................................................................................28
Copy tips ........................................................................................................................................................ 28
Chapter 3: E-mail .............................................................................................................. 29
Entering an e-mail address ............................................................................................................................29
Using a shortcut number ................................................................................................................................29
Using the address book .................................................................................................................................30
E-mailing to a profile ......................................................................................................................................30
Adding e-mail subject and message information ........................................................................................... 30
Changing the output file type .........................................................................................................................31
E-mailing color documents ............................................................................................................................31
Creating an e-mail shortcut ............................................................................................................................31
4
Contents
Creating an e-mail profile ...............................................................................................................................32
Canceling an e-mail .......................................................................................................................................32
Understanding e-mail options ........................................................................................................................ 32
E-mail server setup ........................................................................................................................................34
Address book setup .......................................................................................................................................34
Chapter 4: Faxing .............................................................................................................. 35
Sending a fax ................................................................................................................................................. 35
Using fax destination shortcuts ......................................................................................................................36
Using the address book .................................................................................................................................36
Sending faxes from a computer .....................................................................................................................36
Creating shortcuts ..........................................................................................................................................37
Understanding fax options ............................................................................................................................. 38
Changing the fax resolution ...........................................................................................................................39
Adjusting the Darkness setting ......................................................................................................................39
Sending a fax at a later time ..........................................................................................................................39
Cancel an outgoing fax .................................................................................................................................. 40
Viewing a fax log ............................................................................................................................................40
Fax tips .......................................................................................................................................................... 40
Chapter 5: FTP ..................................................................................................................41
Entering the FTP address ..............................................................................................................................41
Using a shortcut number ................................................................................................................................41
Using the address book .................................................................................................................................41
Creating shortcuts ..........................................................................................................................................42
FTP options ...................................................................................................................................................42
FTP tips .........................................................................................................................................................44
Chapter 6: Scanning to a PC or USB flash memory device .......................................... 45
Create a scan to PC profile ............................................................................................................................ 45
Understanding scan to PC options ................................................................................................................46
Scanning to a USB flash memory device ....................................................................................................... 47
Scanning tips .................................................................................................................................................47
Chapter 7: Printing ............................................................................................................ 48
Printing from a USB flash memory device .....................................................................................................48
Canceling a print job ......................................................................................................................................49
Printing the menu settings page ....................................................................................................................51
Printing a network setup page ....................................................................................................................... 51
Printing a font sample list ............................................................................................................................... 51
Printing a directory list ...................................................................................................................................51
Printing confidential and held jobs .................................................................................................................52
Printing on specialty media ............................................................................................................................55
Loading standard trays and optional trays .....................................................................................................56
Setting the Paper Type and Paper Size ........................................................................................................58
5
Contents
Loading the multipurpose feeder ................................................................................................................... 58
Loading the 2000-sheet drawer .....................................................................................................................61
Loading the envelope feeder .........................................................................................................................63
Linking trays ................................................................................................................................................... 65
Chapter 8: Understanding paper and specialty media guidelines ............................... 66
Supported print media ................................................................................................................................... 66
Selecting print media .....................................................................................................................................73
Storing print media .........................................................................................................................................76
Avoiding jams ................................................................................................................................................ 77
Chapter 9: Installing and removing options ................................................................... 79
Installing memory or option cards ..................................................................................................................79
Accessing the MFP system board .................................................................................................................79
Installing or removing a memory card ............................................................................................................82
Installing or removing a flash memory or firmware card ................................................................................ 84
Installing an option card .................................................................................................................................86
Replacing the shield ......................................................................................................................................87
Chapter 10: Maintaining the MFP .................................................................................... 88
Determining the status of supplies ................................................................................................................. 89
Ordering supplies ...........................................................................................................................................89
Recycling Lexmark products ..........................................................................................................................90
Cleaning the scanner glass and backing material ......................................................................................... 90
Cleaning the automatic document feeder ......................................................................................................91
Scanner registration .......................................................................................................................................92
Removing the scanner top .............................................................................................................................93
Moving the MFP .............................................................................................................................................94
Chapter 11: Clearing jams ................................................................................................ 95
Identifying jams ..............................................................................................................................................95
Access doors and trays .................................................................................................................................96
Understanding jam messages .......................................................................................................................97
Clearing printer jams ......................................................................................................................................98
Clearing scanner jams ...................................................................................................................................98
Chapter 12: Administrative support ................................................................................ 99
Adjusting control panel brightness ................................................................................................................. 99
Restoring factory default settings ..................................................................................................................99
Adjusting screen timeout ............................................................................................................................. 100
Adjusting Power Saver ................................................................................................................................ 100
Configuring the MFP ....................................................................................................................................101
Encrypting the hard disk ..............................................................................................................................107
Hard disk wiping ..........................................................................................................................................108
Using the Restricted Server List function .....................................................................................................108
6
Contents
Chapter 13: Troubleshooting ......................................................................................... 109
Understanding MFP messages ...................................................................................................................109
Online technical support ..............................................................................................................................109
Checking an unresponsive MFP ..................................................................................................................109
Locating the port name and IP address .......................................................................................................109
Solving copy quality problems .....................................................................................................................110
Solving scan quality problems .....................................................................................................................110
Solving fax problems ...................................................................................................................................111
Solving paper feed problems .......................................................................................................................111
Notices .............................................................................................................................. 112
Conventions .................................................................................................................................................112
Electronic emission notices .........................................................................................................................112
Other telecommunications notices ...............................................................................................................117
ENERGY STAR ...........................................................................................................................................119
Waste from Electrical and Electronic Equipment (WEEE) directive .............................................................119
Index .................................................................................................................................. 120
Learning about the MFP
7
1
Learning about the MFP
Basic functions of the scanner
Note: Faxing is not supported on all models.
The
Lexmark™ 4600 MFP option provides copy, fax, and scan-to-network capability for large workgroups. You can:
Make quick copies, or change the settings on the control panel to perform specific copying jobs.
Send an outgoing fax using the MFP control panel.
Send an outgoing fax to multiple fax destinations at the same time.
Scan documents and send them to your PC, an e-mail address, a USB flash memory device, or an FTP
destination.
Scan documents and send them to another printer (PDF by way of FTP).
Automatic document feeder and flatbed
Note: Color documents can be scanned to a PC, e-mail address, or an FTP destination. Printed output on
this MFP is black and grayscale only, not color.
The ADF (automatic document feeder) can scan multiple pages including duplex pages. The ADF has two scanner
elements. When using the ADF:
Place the paper in the ADF faceup, short-edge first.
Place up to 50 sheets of plain paper on the ADF input tray.
Scan media from 114.0 x 139.4 mm (4.5 x 5.5 in.) to 215.9 x 355.6 mm (8.5 x 14 in.).
Scan jobs with mixed page sizes (letter and legal).
Scan media weight from 52 to 120 g/m
2
(14 to 32 lb).
Note: Color documents can be scanned to a PC, e-mail address, or an FTP destination.
Copy and print documents at 600 dpi
Note: Printed output is black and grayscale only, not color.
The flatbed (platen) can be used to scan or copy single pages or book pages. When using the flatbed:
Place the document in the left rear corner.
Scan or copy media up to 215.9 x 355.6 mm (8.5 x 14 in.).
Copy books up to 25.3 mm (1 in.) thick.
Copy and print documents at 600 dpi.
Understanding the MFP control panel
8
Learning about the MFP
Understanding the MFP control panel
MFP and scanner settings can be changed several ways: through the MFP control panel, the software application in use,
the print driver, MarkVision™ Professional, or the Web pages. Settings changed from the application or print driver apply
only to the job being sent to the MFP.
Changes made to print, fax, copy, and e-mail settings from an application override changes made from the control panel.
Note: Faxing is not supported on all models.
If a setting cannot be changed from the application, use the MFP control panel, MarkVision Professional, or the Web pages.
Changing a setting from the MFP control panel, MarkVision Professional, or the Web pages makes that setting the user
default.
The MFP control panel consists of:
Callout Control panel item Function
1 LCD A liquid crystal display (LCD) which shows home screen
buttons, menus, menu items, and values. Allows for
making selections within Copy, Fax, and so on.
2 Indicator light Gives information about the status of the MFP using the
colors red and green.
ABC
DEF
GHI
JKL
MNO
PQRS
TUV
WXYZ
9
10
1
2
3
4
5
6
7
8
Status Indicates
Off MFP power is off.
Blinking green MFP is warming up, processing data,
or printing a job.
Solid green MFP is on, but idle.
Blinking red Operator intervention is required.
Understanding the MFP control panel
9
Learning about the MFP
3 0—9
Note: Referred to as the numeric
keypad.
Press these buttons to enter numbers when the LCD
screen has a field that accepts the entry of numbers.
Also, use these buttons to dial phone numbers for faxes.
Note: If a number is pressed while on the home screen
without pressing the # button first, the Copy menu opens
and changes the Copy Quantity.
4 # (Pound or number character) Press this button:
For a shortcut identifier.
Within phone numbers. For a Fax number with a #,
enter it twice – ##.
From the home screen, the Fax Destination List menu
item, E-mail Destination List menu item, or Profile List
menu item to access shortcuts.
5 Dial Pause Press to cause a two- or three-second dial pause in a fax
number. The button only functions within the Fax menu or
with fax functions.
Press from the home screen to redial a fax number.
When outside of the Fax menu, fax function, or home
screen, pressing Dial Pause causes an error beep.
When sending a fax, in the Fax To: field, a Dial Pause
press is represented by a comma (,).
6 Clear All When in the function menus, such as Copy, Fax, E-mail,
and FTP, it returns all settings to their default values, and
then returns the MFP to the main function screen.
7 Start Press to initiate the current job indicated on the control
panel.
From the home screen, press it to start a copy job with
the default settings.
If pressed while a job runs through the scanner, the
button has no effect.
8 Stop Press to cause the printing or scanning to stop.
During a scan job, the scanner finishes scanning the
current page and then stops, which means paper may
remain in the automatic document feeder (ADF).
During a print job, the print media path is cleared before
the printing stops.
Stopping appears on the control panel during this
process.
9 Backspace Within the Copy menu, which is accessed by touching
the Copy button, press Backspace to delete the right-
most digit of the value in the Copy Count. The default
value of 1 appears if the entire number is deleted by
pressing Backspace numerous times.
Within the Fax Destination List, press Backspace to
delete the right-most digit of a number entered manually.
It also deletes an entire shortcut entry. Once an entire
line is deleted, another press of Backspace causes the
cursor to move up one line.
Within the E-mail Destination List, press Backspace to
delete the character to the left of the cursor. If the entry is
in a shortcut, the entire entry is deleted.
10 Asterisk (*) * is used as part of a fax number or as an alphanumeric
character.
Callout Control panel item Function
Understanding the MFP control panel
10
Learning about the MFP
Home screen and Home screen buttons
After the MFP is turned on and a short warm-up period occurs, the LCD shows the following basic screen which is referred
to as the Home screen. Use the Home screen buttons to initiate an action such as copy, fax, or scan, to open the menu
screen, or to respond to messages.
Callout number Button Function
1 Copy Touch to access the Copy menus.
If the home screen is shown, press a number to access
the Copy menus, too.
2 E-mail Touch to access the E-mail menus. It is possible to scan
a document directly to an e-mail address.
3 Menus (A key is shown on the button.) Touch to access the menus. These menus are only
available when the MFP is in the Ready state.
The Menus button is on a gray bar called the navigation
bar. The bar contains other buttons described as follows.
4 Status message bar Shows the current MFP status such as Ready or Busy.
Shows MFP conditions such as Toner Low.
Shows intervention messages to give instructions on
what the user should do so the MFP can continue
processing, such as Close door or insert print
cartridge.
5 Status/Supplies Appears on the LCD whenever the MFP status includes a
message requiring intervention. Touch it to access the
messages screen for more information on the message
including how to clear it.
6 ? (Tips) All menus have a Tips button. Tips is a context-sensitive
Help feature within the LCD touch screens.
1
2
3
4
5
6
7
8
Copy
Fax
E-mail
FTP
Status/
Supplies
Ready. Toner low.
Touch any button to begin.
Menus
Understanding the MFP control panel
11
Learning about the MFP
Other buttons may appear on the Home screen. They are:
7 FTP Touch to access the File Transfer Protocol (FTP) menus.
A document can be scanned directly to an FTP site.
Note: This function must be set up by your System
Support person to appear on the display.
8 Fax Touch to access the Fax menus.
Button Button name Function
Release Held Faxes
(or Held Faxes if in
Manual Mode)
There are held faxes with a scheduled hold time previously set. To
access the list of held faxes, touch this button.
Search Held Jobs To search on any of the following items and return any matches:
User names for held or confidential print jobs
Job names for held jobs, excluding confidential print jobs
Profile names
Bookmark container or job names
USB container or job names for supported extensions only
Held Jobs To open a screen containing all the held jobs containers.
Lock Device This button appears on the screen when the MFP is unlocked and
Device Lockout Personal Identification Number (PIN) is not null or
empty.
To lock the MFP:
1 Touch Lock Device to open a PIN entry screen.
2 Enter the correct PIN to lock the control panel which locks both the
control panel buttons and the touch-screen buttons.
Once the control panel is locked, the PIN entry screen clears, and
the Lock Device button is replaced with the Unlock Device button.
Note: If an invalid PIN is entered, Invalid PIN. appears. A pop-up
screen appears with the Continue button. Touch Continue. The home
screen returns with the Lock Device button.
Callout number Button Function
Understanding the MFP control panel
12
Learning about the MFP
Unlock Device This button appears on the screen when the MFP is locked. The
control panel buttons and shortcuts cannot be used while it appears,
and no default copy starts may occur.
To unlock the MFP:
1 Touch Unlock Device to open a PIN entry screen.
2 Enter the correct PIN to unlock the numeric keypad (0—9) and the
Backspace button on the control panel.
Note: If an invalid PIN is entered, Invalid PIN. appears. A pop-up
screen appears with the Continue button. Touch Continue. The home
screen returns with the Unlock Device button.
Cancel Jobs To open the Cancel Jobs screen. The Cancel Jobs screen shows any
of the following items under three headings on the screen, which are
Print, Fax, and Network:
•print job
copy job
•fax
profile
•FTP
e-mail send
Each heading has its own list of jobs shown in a column under the
heading. Each column can only show three jobs per screen. The job
appears as a button. If more than three jobs exist in a column, then the
down arrow appears at the bottom of the column. Each touch of the
down arrow accesses one job in the list. When more than three jobs
exist, once the fourth job in the list is reached, then an up arrow
appears at the top of the column. For illustrations of the up and down
arrow buttons, see Information on touch-screen buttons.
To cancel a job, see the Canceling a print job for instructions.
Button Button name Function
Cancel
Jobs
Using the LCD touch-screen buttons
13
Learning about the MFP
Using the LCD touch-screen buttons
The following section provides information on navigating through several screens. Only a few are chosen to demonstrate
the use of the buttons.
Note: Depending on your options and administrative setup, your screens and buttons may vary from those
shown.
Sample screen one
Information on touch-screen buttons
Button Button name Function or description
Select button Touch the select button to have another screen appear with additional
items. On the first screen, the user default setting is shown. Once the
select button is touched, and the next screen appears, touching
another item shown on the screen changes the user default setting.
Left scroll decrease
button
Touch the left scroll decrease button to scroll to another value in
decreasing order.
Copy from
Letter (8.5 x 11 in.)
Copy to
Letter (8.5 x 11 in.)
Plain Paper
Sides (Duplex)
Portrait
1-sided to 1-sided
Content
Scale
Auto
(100%)
Darkness
Scan the
ADF
Scan the
flatbed
Back
Text Text/Photo
Photograph Printed Image
Using the LCD touch-screen buttons
14
Learning about the MFP
Right scroll increase
button
Touch the right scroll increase button to scroll to another value in
increasing order.
Left arrow button Touch the left arrow button to scroll left to:
Reach a decreased value shown by an illustration.
See a full text field on the left.
Right arrow button Touch the right arrow button to scroll right to:
Reach an increased value shown by an illustration.
See a full text field on the right.
Scan the ADF
Scan the flatbed
On the gray navigation bar, these two choices indicate that two types
of scanning are possible. One may choose to scan from the ADF or
the flatbed.
Submit A green button indicates a choice. If a different value within a menu
item is touched, it needs to be saved to become the current user
default setting. To save the value as the new user default setting,
touch Submit.
Back When the Back button is shaped like this, no other navigation is
possible from this screen except to go back. If any other choice is
made on the navigation bar, the screen closes.
For example, in Sample screen one, all the selections for scanning
have been made. One of the preceding green buttons should be
touched. The only other button available is Back. Touch Back to return
to the previous screen, and all the settings for the scan job made on
Sample screen one are lost.
Back When the Back button is shaped like this, both forward and backward
navigation is possible from this screen, so there are other options
available on the screen besides selecting Back.
Button Button name Function or description
Scan the
ADF
Scan the
flatbed
Submit
Back
Back
Using the LCD touch-screen buttons
15
Learning about the MFP
Sample screen two
Information on touch-screen buttons
Button Button name Function or description
Down arrow Touch the down arrow to move down to the next item in a list,
such as a list of menu items or values. The down arrow does
not appear on a screen with a short listing. It only appears if
the entire listing cannot be seen on one screen. On the last
screen of the listing, the down arrow is gray to indicate that it
is not active since the end of the list appears on this screen.
Up arrow Touch the up arrow to move up to the next item in a list, such
as a list of menu items or values. When on the first screen
presented with a long list, the up arrow is gray to indicate that
it is not active. On the second screen needed to show the rest
of the listed item, the up arrow is blue to show that it is active.
Unselected radio button This is an unselected radio button.
Unknown paper size. Copy from:
Letter (8.5 x 11 in.)
Legal (8.5 x 14 in.)
Executive (7.25 x 10.5 in.)
Continue
Cancel
Job
A4 (210 x 297 mm)
Folio (8. 5 x 13 in.)
Statement (5.5 x 8.5 in.)
Using the LCD touch-screen buttons
16
Learning about the MFP
Other touch-screen buttons
Selected radio button This is a selected radio button. Touch a radio button to select
it. The radio button changes color to show it is selected. In
Sample screen two, the only paper size selected is Letter.
Cancel Job See Cancel Jobs on page 12.
Continue Touch Continue after a menu item or value on a screen is
selected and more changes need to be made for a job from
the original screen. Once Continue is touched, the original
screen appears.
For example, if one touched Copy on the home screen, the
Copy screen appears like Sample screen one on page 13.
The following example shows how the Continue button
reacts.
1 Touch the select button by the Copy to box, and a new
screen appears.
2 Touch MP Feeder, and a new screen appears.
3 Touch Legal, and a new screen appears.
4 Touch Next, and a new screen appears.
5 Touch Plain Paper for the type of print media needed.
6 Touch Continue. The Copy screen returns to allow other
selections besides Copy to. The other settings on the Copy
screen available are Duplex, Scale, Darkness, Collate, and
Copies.
Touch Continue to return to the original screen and make
other setting changes for a copy job before the Copy it
button is touched to start the job.
Button Button name Function or description
Custom Allows for creating a custom button based on the
user’s needs.
Cancel Touch Cancel to cancel an action or a selection.
Touch to cancel out of a screen and return to the
previous screen.
Button Button name Function or description
Cancel
Job
Continue
Cancel
Using the LCD touch-screen buttons
17
Learning about the MFP
Select Touch to select a menu. The next screen appears
showing menu items.
Touch to select a menu item. The next screen appears
showing values.
Done Allows specifying that a job is finished. For example,
when scanning an original document, one could
indicate that the last page is scanned, and then printing
the job would begin.
Back Touch the Back button to return to the previous screen,
and no settings are saved on the screen where it was
touched. The Back button appears on each menu
screen except for the home screen.
Home Touch the Home button to return to the home screen.
The Home button appears on every screen except the
home screen. See the Home screen and Home
screen buttons on page 10 for more information.
Grayed out button When this button appears, it looks faded with a faded
word on it. It means the button is not active or
unavailable on this screen. It was probably active on
the previous screen, but the selections made on the
previous screen caused it to be unavailable on the
current screen.
Gray button Touch this button to select the action appearing on the
button.
Button Button name Function or description
Done
Back
Using the LCD touch-screen buttons
18
Learning about the MFP
Features
Feature Feature name Description
Menus
Æ Settings
Æ Copy Settings
Æ Number of
Copies
Menu trail line A line is located at the top of each menu screen. This
feature acts as a trail. It gives the exact location within
the menus. Touch any of the underlined words to return
to that menu or menu item. The Number of Copies is not
underlined since this is the current screen.
If this feature is used on the Number of Copies screen
before the Number of Copies is set and saved, then the
selection is not saved, and it does not become the user
default setting.
Attendance message alert If an attendance message occurs which closes a
function, such as copy or fax, then a solid red
exclamation point appears over the function button on the
home screen. This feature indicates that an attendance
message exists.
Press Status/Supplies to see the current status of the
MFP.
Menus
19
Learning about the MFP
Menus
A number of menus are available to make it easy for you to change MFP settings or print reports. To access the menus and
settings, press the menu button in the lower right corner of the home screen.
When a value or setting is selected and saved, it is stored in MFP memory. Once stored, these settings remain active until
new ones are stored or the factory defaults are restored.
Note: Settings chosen for faxing, scanning, e-mailing, copying, and settings for printing from the application
may override the settings selected from the control panel.
The following diagram shows the touch screen menu index and the menus and items available under each menu. For more
information about menus and menu items, see the Menus and Messages Guide on the Software and Documentation CD.
Paper Menu
Reports
Network/Ports
Settings
Manage Shortcuts
Help
Back
?
Paper Menu
Default Source
Paper Size/Type
Configure MP
Envelope Enhance
Substitute Size
Paper Texture
Paper Weight
Paper Loading
Custom Types
Custom Names
Custom Bin Name
Universal Setup
Bin Setup
Settings
General Settings
Copy Settings
Fax Settings
E-mail Settings
FTP Settings
Print Settings
Security
Set Date and Time
Reports
Menu Settings Page
Device Statistics
Network Setup Page
Shortcut List
Fax Job Log
Fax Call Log
E-mail Shortcuts
Fax Shortcuts
FTP Shortcuts
Profiles List
NetWare Setup Page
Print Fonts
Print Directory
Network/Ports
TCP/IP
IPv6
E-mail Server Setup
Address Book Setup
Wireless
Standard Network
Network <x>
Standard USB
USB <x>
Standard Parallel
Parallel <x>
Standard Serial
Serial <x>
NetWare
AppleTalk
LexLink
Help
Print all guides
Copy guide
E-mail guide
Fax guide
FTP guide
Information guide
Print defects guide
Supplies guide
Manage Shortcuts
Manage Fax Shortcuts
Manage E-mail Shortcuts
Manage FTP Shortcuts
Manage Profile Shortcuts
Copying
20
2
Copying
The following copy topics are available in this and other chapters.
Quick copy
1 Place the original document faceup in the automatic document feeder (ADF) or facedown on the flatbed.
Adjust the paper guides when using the ADF.
2 Press Go on the numeric pad.
Note: If an LDSS profile has been installed, you may receive an error when attempting a quick copy. Contact
your system support person for access.
Multiple page copying
1 Place the original document faceup in the automatic document feeder or facedown on the flatbed.
Adjust the paper guides when using the ADF.
2 Touch Copy on the home screen, or use the numeric keypad to specify the number of copies you want.
After touching Copy or entering the number of copies, the touch screen will automatically change to the copy
settings menu.
3 Change the copy options to meet your requirements.
4 Touch Copy It.
Quick copy Reducing and enlarging copies
Multiple page copying Adjusting copy quality
Using the flatbed Setting collation options
Understanding the copy screens and options Placing separator sheets between copies
Copying from one size to another Setting paper saving options
Making transparencies Placing the date and time at the top of each page
Copying to letterhead Placing an overlay message on each page
Copying photographs Creating a custom job (job build)
Making copies using media from a selected tray Canceling a copy job
Copying mixed-sized media Copy tips
Setting the duplex option Solving copy quality problems
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123

Lexmark T642 - Monochrome Laser Printer User manual

Category
Laser/LED printers
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI