Moog Videolarm POD8C Product Instructions

Brand: Moog Videolarm

Model: POD8C

Category: Camera housings

Type: Product Instructions

This manual is also suitable for

POD8CFW

PRODUCT INSTRUCTIONS

ELECTRICAL SPECIFICATIONS (OUTDOOR ONLY):

Power 24VAC, Class 2 Only

52 watts at 24 VAC (accessories)

Heater: 50 watts

Blower: 1.7 watts

Input Connectors (outdoor units):

BNC

(2) 4 position Molex connectors (power)

(1) Phone style plug (control)

GENERAL INSTRUCTIONS:

Tools Required: .100" Flat Head Screwdriver

Phillips Head Screwdriver

PREPARING PENDANT MOUNT BRACKET FOR POD8C

(For wall mount, POD8CW, see page 3)

1. Carefully remove the housing from the packaging material.

Check to be sure all parts are present.

2. This unit includes a 1 1/2" NPT housing coupling for a standard

1 1/2" NPT pipe. The POD8C can be used with other brackets

designed with 1 1/2" male pipe threads, such as the Panasonic

WM20G and PWM30G brackets.

3. Attach the housing coupling to the bracket or pendant pipe

(Figure 1).

NOTE: Pipe threads should be clean and rust free. Use a

sealer (such as Teﬂ on™ tape or silicone sealer) on the

threads.

Figure 1

Add thread

sealing tape

Be sure the bracket is properly and securely mounted

to a supporting structure capable of rigidly holding the

weight of the entire unit.

INSTALLING QUICK RELEASE BRACKET AND PAN/TILT

CAMERA ASSEMBLY (ALL MODELS)

1. Open the housing by loosening the (3) captive screws located

on the housing ring next to the lower clear dome. Be careful

not to back these all the way out. Twist the dome slightly in a

counterclockwise motion to remove (Figure 2).

Figure 2

Loosen screws only,

do not remove

Remove dome by

twisting coun ter -

clock wise

2. Install the pan/tilt unit quick- release bracket. It is recom-

mended that this be done before installing the housing.

3. Spacers are provided to adjust the level of the WV-CS854

camera. Attach the spacers, two-high, to the main housing

bracket (Figure 3).

MODEL: Outdoor Dome Housing

POD8C(W), POD8CF(W), PID8C

Manufactured by:

Before attempting to connect or operate this product, please read these instructions completely.

81-IN3074

5/19/04

Figure 3

2525 Park Central Blvd. • Decatur, Ga 30035 • (770) 987-7550 • 800-554-1124 U.S. & Canada • www.videolarm.com • Fax 800-826-0366

for

NOTE: This unit is designed for operation in an

upright position. Installing the unit

upside down may cause damage to the

internal equipment, and will void the war-

ranty.

- 2 -

Safety Screw

4. Connect the quick-release bracket to the spacers using the (4) 8 x

32 x 1/2" bolts and #8 star washers (Figure 4).

Figure 4

5. Attach the unitized camera to the quick-release bracket. Secure

the safety screw (Figure 5). Connect the BNC, power, control,

and alarm cables. Make sure all wiring is clear of the blowers and

heater on the housing bracket. Use the cable tie provided to

secure the wires and connectors.

Figure 5

NOTE: Remove the plastic dome from the WV-CS854 unitized

camera to ensure the best optical picture.

INSTALLING FIXED CAMERA BRACKET (ALL MODELS)

1. Loosen the two pan adjustment screws and rotate the bracket to

the desired viewing location.

2. Tilt and height adjustments can be made using the two screws

located on the upper portion of the ﬁ xed camera bracket. Loosen-

ing the screws allows the bracket itself to slide up and down the

bracket arms (height adjustment) and back and forth on the cam-

era bracket (tilt). Adjust to the desired location (Figure 7).

3. The camera can also be adjusted back and forth via the slot

located on the bottom of the bracket (Figure 8).

4. Attach the camera to the bracket using the 1/4-20 hex bolt

provided. Make ﬁ nal adjustments and lock down the pan, tilt, and

height adjustment screws (Figure 10).

IMPORTANT NOTE: Put the dome in place to assure the camera

does not touch it. To reattach the dome you must twist it, if the

dome comes in contact with the camera its position could change.

Figure 6

Figure 7

Figure 8

Figure 10

Pan

adjustment

screw

Tilt

adjustment

screw

Pan

adjustment

screw

1/4-20 hex bolt

NOTE: A 90˚ BNC connector is included in the packet to assist in

ﬁ tting the camera (Figure 9).

Figure 9

- 3 -

Figure 12

Twist and

Secure

1. A wall mount bracket comes standard with this unit, and a

template is included to use as a guide for mounting the bracket

to a wall. Choose the desired location for installation and mark

the drill holes using the template. Screw (2) bolts (not

provided) about 3/4 of the way into the (2) top holes. Run

approximately 8" of wiring out of the wall.

2. Open the access door on the bottom of the wall mount by

loosening the screw nearest the mounting plate.

3. Slip the housing onto the top (2) bolts and pull the wires from the

wall through the rectangular hole in the wall mount bracket.

Screw bolts and washers through the bottom (2) holes and

secure. Remove the top (2) bolts, add washers, and reattach,

tightening completely.

4. Attach the wires from the wall to the connector provided, using the

wiring color code chart as a guide.

5. Once all wiring connections are made, place the wires inside the

wall mount bracket and close the access door. Secure with the

screw removed earlier.

6. Clean the outside of the dome.

INSTALLING THE HOUSING ASSEMBLY

FOR WALL MOUNT POD8CW (Figure 11)

FOR PENDANT MOUNT, POD8C (Figure 12)

1. Mount the housing assembly to the mounting bracket and

housing coupling. A safety cable is included with the housing to

temporarily hold it while making wiring connections. Loop the

safety cable over one of the set screws on the housing coupling

and make the appropriate connections using the (2) screw-down

connectors supplied.

2. Undo the safety cable and twist the housing onto the housing

coupling. Secure all (3) setscrews provided on the housing

coupling (Figure 4).

3. Clean the outside of the dome.

Wiring Color Code

Power and Control Inputs

1 24 VAC Live Black

2 24 VAC Live White

3 Green Green

4 Not Used

1 24 VAC Live Red

2 24 VAC Live White

3 Green Green

4 Not Used

1 Ground Brown

2 TXB (RS485) Red

3 TXA (RS485) Orange

4 RXB (RS485) Yellow

5 RXB (RS485) Green

CAMERA POWER

ACCESSORY POWER

CONTROL

Figure 11

POD8C

Pan/Tilt Unit Only

1 Alarm In 1 Black

2 Ground Brown

3 Alarm In 2 Red

4 Ground Orange

5 Alarm In 3 Yellow

6 Ground Light blue or green

7 Alarm In 4 Blue

8 Ground Purple

ALARM IN (8-pin)

1 Alarm Out 1 Gray

2 Ground White

3 Alarm Out 2 Pink

4 Ground Yellow, Green, or Light blue

ALARM OUT (4-pin)

Loosen screw to open

access door

- 4 -

FOR INDOOR PENDANT, PID8C

1. Select desired location to install housing.

2. The housing coupling is designed for a 1.0” NPT thread pipe.

Install the required length of pipe. Feed all power, control and

video wires through the pipe leaving approximately 12” of extra

wire extending from the end.

3. Install the housing top to the 1” pipe. Feed all wires into housing

(Figure 5).

4. Attach the quick release bracket for the unitized camera system

(See page 2).

5. Make electrical connections to the bracket, trim ming wire leads as

required.

6. Clean the inside of the dome. Reattach the hous ing dome and

secure the (3) captive screws. Do not over tighten the screws.

Figure 13

Parts List

1. Housing

2. Housing Coupling

3. Housing Packet

a. (2) Mates for screw down connectors (not supplied with

indoor units)

b. (1) Adapter plate

c. (8) 1/2" standoffs

d. (8) 8 x 32 x 3/8" Mounting screws with star washers

e. (3) 6 x 32 x 3/8" Mounting screws with star washers

f. (2) 1/4 x 20 x 3/8" HH Bolts

g. (2) 1/4” Flat washers

h. (2) 1/4" Split Lock washers

i. Instruction Manual

j. (2) Jumpers

Feed all wiring

into housing

- 5 -

17 1/4 x 20 FH SS Bolt 90-BTSR01 1

18 Housing Pendant Bracket 30-VL926 1

19 1/4 Split Lock Washer 92-WSSL01 1

20 1/4 Flat Washer 92-WSFL01 1

21 Housing Gasket 96-PSGK05 1

22 1/4 x 20 x 1/2" Set Screw 90-BTSS05 2

23 1/4 Flat Washer 92-WSFL01 4

24 1/4 Split Lock Washer 92-WSSL01 4

25 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

26 1 1/2" Housing Coupling 30-VL1938 1

27 Upper Housing Gasket 96-PSGK04 1

28 1/4 x 20 x .375" HH Bolts 90-BTHH39 2

n/s 1/4 Flat Washer 92-WSFL01 2

n/s 1/4 Split Lock Washer 92-WSSL01 2

Item No. Description Part No. Qty

1 Wall Mount Bracket Assembly 50-WM10B 1

2 POD8 Housing Top 30-VL2156 1

3 Dome Support Ring 30-VL1695 1

4 25W, 24VAC w/Leads 72-HT1752 2

5 POD8 Clear Dome 20-DCFD8/06 1

n/s POD8 Tinted Dome 20-DTFD8/06 1

n/s 9.25" O-ring 96-RSORG11 2

6 Plastic Ring Plugs 30-VL1696 6

7 PCB 76-POD8PCB 1

8 FD8 Upper Housing Bracket 30-VL1744 1

9 Housing Gasket 96-PSGK05 3

10 Housing Fan 71-VLBL03 1

12 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

12 1/4 Split Lock Washer 92-WSSL01 4

12 1/4 Flat Washer 92-WSFL01 4

13 10 x 32 x .75 Phil PH SS 90-BTRP28 3

15 Captive Screw 30-VL1749 3

n/s Captive Screw Spring 92-SPR01 3

n/s Captive Screw Retainer 94-FSRT04 3

16 Main Housing Bracket 30-VL2141 1

n/s Housing Ring 1" Lanyard Spring 92-SPR02 1

n/s Lanyard Spring Screws 90-BTPEM01 2

Pendant Assembly

Wall Mount Assembly

EXPLODED VIEWS OF HOUSING

29 PID8 Upper Housing Bracket 30-VL1013 1

30 Indoor Housing Coupling 30-VL1744 1

31 1/4 Flat Washer 92-WSFL01 1

32 1/4 Split Lock Washer 92-WSSL01 4

33 1/4 x 20 x .75" HH Bolts 90-BTHH27 4

Indoor Pendant As sem bly

- 6 -

2.000

3.250

R .733

2.132

2.981

1.537

5.500

Mounting Template

- 7 -

SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS

1. Read Instructions - All the safety and operating in struc tions

should be read before the unit is operated.

2. Retain Instructions - The safety and operating in struc tions

should be retained for future reference.

3. Heed Warnings - All warnings on the unit and in the operating

instructions should be ad hered to.

4. Follow Instructions - All operating and user in struc tions should

be followed.

5. Electrical Connections - Only a qualiﬁ ed electrician should make

electrical connections.

6. Attachments - Do not use attachments not rec om mend ed by the

product man u fac tur er as they may cause hazards.

7. Cable Runs - All cable runs must be within permissible

distance.

8. Mounting - This unit must be properly and securely mount ed to

a supporting structure capable of sustaining the weight of the

unit. Accordingly:

a. The installation should be made by a qualiﬁ ed service person,

and should conform to all local codes.

b. Care should be exercised to select suitable hardware to

install the unit, tak ing into account both the composition of

the mount ing surface and the weight of the unit. Be sure to

periodically examine the unit and the sup port ing structure to

make sure that the integrity of the in stal la tion is intact. Failure

to comply with the foregoing could result in the unit separating

from the support structure and falling, with resultant damages

or injury to any one or anything struck by the falling unit.

UNPACKING

Unpack carefully. Electronic components can be damaged

if improperly handled or dropped. If an item appears to have

been damaged in shipment, replace it properly in its carton

and notify the shipper.

Be sure to save:

1. The shipping carton and packaging material. They are

the safest material in which to make future ship ments of

the equipment.

2. These Installation and Operating Instructions.

SERVICE

For service on Panasonic/Videolarm equipment contact:

Panasonic Technical Center

54 West Gude Dr.

Rockville MD 20850-1150

Phone: 301-762-5125

Fax: 301-251-0347

1-800-528-6747

9:00 AM - 5:00 PM EASTERN TIME

CAUTION: TO REDUCE THE RISK OF

ELECTRICAL SHOCK, DO NOT EXPOSE

COMPONENTS TO WATER OR MOISTURE.

The lightning flash with an ar row head symbol,

within an equi lat er al triangle, is intended

to alert the user to the pres ence of non-

insulated "dangerous volt age" within the

product's enclosure that may be of sufficient

mag ni tude to con sti tute a risk of electric shock

to persons.

The exclamation point within an equi lat er al

triangle is intended to alert the user to presence

of important operating and main te nance

(ser vic ing) in struc tions in the literature

ac com pa ny ing the ap pli ance.

PANASONIC TECHNICAL SUP PORT

CAUTION

RISK OF

ELECTRIC SHOCK!

Moog Videolarm POD8C Product Instructions

Brand: Moog Videolarm

Model: POD8C

Category: Camera housings

Type: Product Instructions

This manual is also suitable for

POD8CFW

Download PDF

report

Moog Videolarm POD8C Product Instructions

This manual is also suitable for

Moog Videolarm POD8C Product Instructions

Related papers

Other documents