Utilitech 148007 User manual

Type
User manual

This manual is also suitable for

Utilitech 148007 is a powerful and versatile utility transfer pump designed to move water quickly and efficiently. With its heavy-duty construction and durable components, this pump is ideal for a variety of applications, including:

  • Transferring water from one location to another
  • Draining flooded areas
  • Watering lawns and gardens
  • Filling pools and hot tubs

The Utilitech 148007 features a 1/2 horsepower motor that delivers up to 2600 gallons of water per hour. The pump is also self-priming, meaning it can be used to pump water from a depth of up to 25 feet.

The Utilitech 148007 comes with a variety of attachments, including a garden hose adapter, a discharge hose, and a strainer. This makes it easy to connect the pump to a variety of water sources and discharge points.

Utilitech 148007 is a powerful and versatile utility transfer pump designed to move water quickly and efficiently. With its heavy-duty construction and durable components, this pump is ideal for a variety of applications, including:

  • Transferring water from one location to another
  • Draining flooded areas
  • Watering lawns and gardens
  • Filling pools and hot tubs

The Utilitech 148007 features a 1/2 horsepower motor that delivers up to 2600 gallons of water per hour. The pump is also self-priming, meaning it can be used to pump water from a depth of up to 25 feet.

The Utilitech 148007 comes with a variety of attachments, including a garden hose adapter, a discharge hose, and a strainer. This makes it easy to connect the pump to a variety of water sources and discharge points.

1. Pump (A) should be located within 15 ft. of the water
source, and strainer (C) should be used at the end of
the inlet line. Attach hose adapters (B) and reinforced
suction hose (not provided) to pump. Make sure inlet
connection is air tight. NOTE: Regular garden hose
should not be used on pump (A) inlet. It will collapse
when the pump runs. Hoses that expand and contract
will not allow the pump to operate.
3. PUMP MUST BE PRIMED BEFORE USING!
Remove priming plug from the top of pump (A).
Fill pump (A) housing with clean water. Reinstall
plug.
DO NOT RUN DRY.
4. Plug in power cord to grounded outlet. Pump
(A) will prime in a few minutes, depending on
suction line length.
SW1113 B
QUICK START
GUIDE.
SEE INSTRUCTION
MANUAL FOR
COMPLETE DETAILS.
WARNING:
FOR YOUR PROTECTION, ALWAYS DISCONNECT
PUMP FROM POWER SOURCE BEFORE HANDLING.
IN
OUT
2. Attach discharge hose (not provided) to pump
(A) outlet. A standard 3/4 in. garden hose may be
used as a discharge line.
CAUTION: Keep the total length as short as
possible for best performance.
IN
OUT
5. If the pump (A) does not pump water after ve
minutes, turn o the pump and repeat steps 1
through 3.
DO NOT RUN DRY.
ITEM #0955642
UTILITY
TRANSFER
PUMP
MODEL #
148007
Printed in China
A
B
C
Use only rigid pipe or
reinforced hose on the
pump inlet. Hoses that
expand and contract will
not allow the pump to
operate.
Toll Free Help Line: 1-866-994-4148
A
A
A
A
1. La bomba (A) se debe ubicar dentro de los 4,57
metros de la fuente de agua y el colador (C) se
debe usar al nal de la tubería de entrada. Fije los
adaptadores de manguera (B) y la manguera de
succión reforzada (no se proporciona) a la bomba.
Asegúrese de que la conexión de entrada esté
cerrada herméticamente. NOTA: no se debe usar
una manguera para jardín común en la entrada de la
bomba (A). Colapsará cuando la bomba arranque. Las
mangueras que se expanden y contraen no permitirán
que la bomba funcione.
3. ¡DEBE CEBAR LA BOMBA ANTES DE
UTILIZARLA!
Retire de la parte superior de la bomba (A).Llene
la carcasa de la bomba (A)
con agua limpia. Vuelva a
instalar el tapón.
NO HAGA FUNCIONAR
LA BOMBA EN SECO.
4. Conecte el cable de alimentación a un
tomacorriente con conexión a tierra. La bomba
(A) se cebará en unos minutos según el largo
del tubo de succión.
GUÍA DE INICIO
RÁPIDO. CONSULTE
LOS DETALLES
COMPLETOS EN
EL MANUAL DE
INSTRUCCIONES
ADVERTENCIA:
PARA SU PROTECCIÓN, DESCONECTE SIEMPRE LA BOMBA
DE LA FUENTE DE SUMINISTRO ELÉCTRICO ANTES DE
MANIPULARLA.
Entrada
Salida
2. Fije la manguera de descarga (no se proporciona)
a la salida de la bomba (A). Se puede usar una
manguera para jardín estándar de 1,90 cm como
tubería de descarga.
PRECAUCIÓN: Mantenga el largo total lo más corto
posible para obtener un mejor rendimiento.
Entrada
Salida
5. Si la bomba (A) no bombea agua después de cinco
minutos, apague la bomba y repita los pasos del 1
al 3.
NO HAGA FUNCIONAR
LA BOMBA EN SECO.
ARTÍCULO #0955642
BOMBA DE
TRANSFERENCIA
PARA USO
GENERAL
MODELO #
148007
Hecho en China
A
B
C
Línea gratuita de ayuda: 1-866-994-4148
Utilice únicamente tubos rígidos
o mangueras reforzadas en
la entrada de la bomba. Las
mangueras que se expanden y
contraen no permitirán que la
bomba funcione.
A
A
A
A
  • Page 1 1
  • Page 2 2

Utilitech 148007 User manual

Type
User manual
This manual is also suitable for

Utilitech 148007 is a powerful and versatile utility transfer pump designed to move water quickly and efficiently. With its heavy-duty construction and durable components, this pump is ideal for a variety of applications, including:

  • Transferring water from one location to another
  • Draining flooded areas
  • Watering lawns and gardens
  • Filling pools and hot tubs

The Utilitech 148007 features a 1/2 horsepower motor that delivers up to 2600 gallons of water per hour. The pump is also self-priming, meaning it can be used to pump water from a depth of up to 25 feet.

The Utilitech 148007 comes with a variety of attachments, including a garden hose adapter, a discharge hose, and a strainer. This makes it easy to connect the pump to a variety of water sources and discharge points.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

in other languages