GenTite GTM4S2RP Operating instructions

Brand
GenTite
Model
GTM4S2RP
Type
Operating instructions

GenTite GTM4S2RP is a Membrane Screw with Plate that can be used in many GenTite Roofing systems for attachment of GenTite membrane to steel, wood, and other approved decks. It is manufactured to conform to the physical property requirements of Factory Mutual Specification #4470. The screw has a #3 Phillips drive and a patented X-Point fastener tip. The plate is made of AZ55 Galvanized Steel and has a diameter of 2-3/8” (60.2mm) and a thickness of 0.036”-0.042” (0.9-1.1mm). The screw should be positioned over the GenTite membrane and installed per Gentite Application Instructions.

GenTite GTM4S2RP is a Membrane Screw with Plate that can be used in many GenTite Roofing systems for attachment of GenTite membrane to steel, wood, and other approved decks. It is manufactured to conform to the physical property requirements of Factory Mutual Specification #4470. The screw has a #3 Phillips drive and a patented X-Point fastener tip. The plate is made of AZ55 Galvanized Steel and has a diameter of 2-3/8” (60.2mm) and a thickness of 0.036”-0.042” (0.9-1.1mm). The screw should be positioned over the GenTite membrane and installed per Gentite Application Instructions.

Product Data Sheet
Membrane Screw with Plate
GenTite™ RRS
250 West 96
th
Street
Indianapolis, IN 46260
800-443-4272 ● www.GenTite.com
Page 1 of 2
05/2011
DESCRIPTION
GenTite Membrane Screw with Plate can be used in many GenTite Roofing systems for attachment of
GenTite membrane to steel, wood, and other approved decks. GenTite Membrane Screw with Plate is
manufactured to conform to the physical property requirements of Factory Mutual Specification #4470.
INSTALLATION
GenTite Membrane Screw with Plate should be positioned over the GenTite membrane and installed per
Gentite Application Instructions.
RecommendedFastenerPenetrationintoDeck
Steel Deck – Minimum of 3/4” (19.1 mm) required penetration
Wood Deck – Minimum of 1” (25.4 mm) required penetration
PRODUCTDATA
SIZE QUANTITY PRODUCT #
5” (101.6 mm) Fastener
2” (50.8 mm) round Plate
100 Each (Fastener and
Plate) per Carton
W59GT51020
STORAGE
Screws with Plates should be protected from moisture and kept dry at all times. If stored out of doors,
place on skids in a dry area and cover with a breathable tarp.
SHELFLIFE
Not applicable
PRECAUTIONARYDATA
• Refer to Material Safety Data Sheet for additional information.
• Eye protection is recommended when installing the fasteners.
Product Data Sheet
Membrane Screw with Plate
GenTite™ RRS
250 West 96
th
Street
Indianapolis, IN 46260
800-443-4272 ● www.GenTite.com
Page 2 of 2
05/2011
FASTENERPHYSICALPROPERTIES
PROPERTY MINIMUM PERFORMANCE
Material SAE 1022 Heat Treated Steel
Diameter .245” (6.2 mm)
Thread Modified Buttress
Head Style #3 Phillips Drive
Corrosion Coating Gray CR-10 applied by Electro
coating
Fastener Tip Patented X-Point
PLATEPHYSICALPROPERTIES
PROPERTY MINIMUM PERFORMANCE
Material AZ55 Galvanized Steel
Diameter 2-3/8” (60.2mm)
Thickness 0.036”-0.042” (0.9-1.1mm)
Hole Diameter ¼” (6mm)
Edge Deburred
LEEDINFORMATION
Recycled Content
Post Consumer
Post Industrial
25%
0%
  • Page 1 1
  • Page 2 2

GenTite GTM4S2RP Operating instructions

Brand
GenTite
Model
GTM4S2RP
Type
Operating instructions

GenTite GTM4S2RP is a Membrane Screw with Plate that can be used in many GenTite Roofing systems for attachment of GenTite membrane to steel, wood, and other approved decks. It is manufactured to conform to the physical property requirements of Factory Mutual Specification #4470. The screw has a #3 Phillips drive and a patented X-Point fastener tip. The plate is made of AZ55 Galvanized Steel and has a diameter of 2-3/8” (60.2mm) and a thickness of 0.036”-0.042” (0.9-1.1mm). The screw should be positioned over the GenTite membrane and installed per Gentite Application Instructions.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents