UniTherm IE0245 Operating instructions

Type
Operating instructions
Fiber 2025
Safety Data Sheet
MSDS Number: CL-22-SP
Revision Date: 5-25-16
Page 1 of 4
1. PRODUCT AND COMPANY IDENTIFICATION
2. HAZARDS IDENTIFICATION
Route of Entry: This material may enter the body through inhalation of nuisance dust.
Target Organs: Respiratory system
Inhalation: Sore, raspy throat
Skin Contact: Redness and possible rash; itching
Eye Contact: Itching and redness
Ingestion: N/A
NFPA: Health = 1, Fire = 0, Reactivity = 0
HMIS III: H*1/F0/PH0
GHS Signal Word:
WARNING
GHS Classications:
Health, Respiratory or skin sensitization, 1 Skin
Health, Skin corrosion/irritation, 2
Health, Serious Eye Damage/Eye Irritation, 2 B
Health, Specic target organ toxicity - Single exposure, 3
GHS Phrases:
H317 - May cause an allergic skin reaction
H315 - Causes skin irritation
H320 - Causes eye irritation
H335 - May cause respiratory irritation
GHS Precautionary Statements:
P264 - Wash _ thoroughly after handling.
P333+313 - If skin irritation or a rash occurs: Get medical advice/attention.
P337 - If eye irritation persists: _
Company Identication
UniTherm International Inc.
711 Jones Street
Lewisville, Texas 75057
EMERGENCY TELEPHONE NUMBER:
For emergency involving spill, leak, re,
exposure, or accident call CHEMTREC
(800) 424-9300, day or night
Product Identication
Product Name: Fiber 2025
Common Name(s): Glass Fabric
Fiber 2025
Safety Data Sheet
MSDS Number: CL-22-SP
Revision Date: 5-25-16
Page 2 of 4
P337+313 - Get medical advice/attention
3. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Fibrous Glass (CAS 65997-17-3)
Exposure Limits: OSHA PEL 15 mg/m3 (total), 5 mg/m3 (respirable). ACGIH TLV 1 f/cc
4. FIRST AID MEASURES
Inhalation: Remove person to fresh air. If condition persists, seek medical attention.
Skin Contact: Rinse with copious quantities of cool water. If rash or itching persists, seek
medical attention.
Eye Contact: Rinse with water. Do not rub eyes. Seek medical attention.
Ingestion: Not applicable.
5. FIRE FIGHTING MEASURES
Flash Point (Method Used): >250 C by TOC Flammable Limits
LEL: N/A UEL: N/A
Extinguishing Media: Water, carbon dioxide, or dry chemical
Special Fire Fighting Procedures: Thermal decomposition of ber coating may produce
an irritating mixture of smoke and fumes.
Unusual Fire and Explosion Hazards: None
6. ACCIDENTAL RELEASE MEASURES
Material is a solid in roll form. If accidently released, rewind material back onto roll.
7. HANDLING AND STORAGE
Handling Precautions: Use adequate material handling equipment.
Storage Requirements: Store in dry place. Use may be at temperature extremes based on
product data, but storage should be at ambient temperature.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls: Local exhaust; dust collection
Fiber 2025
Safety Data Sheet
MSDS Number: CL-22-SP
Revision Date: 5-25-16
Page 3 of 4
Personal Protective Equip: HMIS PP, B | Safety Glasses, Gloves
Safety glasses; cotton gloves; long sleeve clothing
Wash thoroughly with soap and water after handling.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Light Tan Fabric
Physical State: Solid
Spec Grav. /Density: 2.5
Boiling Point: N/A
Vapor Pressure: N/A
pH: N/A
Odor: No Odor
Solubility: Negligible
Freezing/Melting Pt.: > 1000°F
Vapor Density: N/A
10. STABILITY AND REACTIVITY
Stability: Material is stable.
Conditions to Avoid: None known.
Materials to Avoid: Strong-oxidizing agents.
Hazardous Decomposition: Carbon monoxide; carbon dioxide
Hazardous Polymerization: Will Not Occur.
11. TOXICOLOGICAL INFORMATION
Direct contact with berglass materials or exposure to airborne berglass dust may irritate
the skin, eyes, nose and throat. Fiberglass can cause itching due to mechanical irritation
from the bers. This is not an allergic reaction to the material. Breathing bers may irritate
the airways resulting in coughing and a scratchy throat. Some people are sensitive to the
bers, while others are not.
12. ECOLOGICAL INFORMATION
No known hazards except for airborne bers caused by nuisance dust. 10 milligrams per
cubic meter for ber diameters less than 7 microns.
13. DISPOSAL CONSIDERATIONS
Incineration preferred in a federal, state, or local approved facility.
14. TRANSPORT INFORMATION
None special required.
Fiber 2025
Safety Data Sheet
MSDS Number: CL-22-SP
Revision Date: 5-25-16
Page 4 of 4
15. REGULATORY INFORMATION
COMPONENT / (CAS/PERC)/ CODES
None known
None known
16. OTHER INFORMATION
Disclaimer:
Although reasonable care has been taken in the preparation of this document, we
extend no warranties and make no representations as to the accuracy or completeness
of the information contained herein, and assume no responsibility regarding the suitability
of this information for the user’s intended purposes or for the consequences of its use.
Individuals should make a determination as to the suitability of the information for their
particular purpose(s).
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 1 of 6
1. PRODUCT AND COMPANY IDENTIFICATION
2. HAZARDS IDENTIFICATION
GHS Classication
Carcinogenicity: Category 2
Label Elements
Signal word: Warning
Hazard statements: Suspected of causing cancer.
Precautionary statements: Prevention:
Obtain special instructions before use.
Do not handle until all safety precautions have been
read and understood.
Use personal protective equipment as required.
Response:
IF exposed or concerned: Get medical advice/
attention.
Storage:
Store locked up.
Disposal:
Dispose of contents/ container to an approved waste
disposal plant.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Chemical nature: Mineral Fiber Product
HAZARDOUS COMPONENTS
Chemical Name CAS-No. Concentration (%)
Mineral wool bres 65997-17-3 >= 50 - < 70 %
non-durable glass wool ber >= 5 - < 10 %
4. FIRST AID MEASURES
Company Identication
UniTherm International Inc.
711 Jones Street
Lewisville, Texas 75057
EMERGENCY TELEPHONE NUMBER:
For emergency involving spill, leak, re,
exposure, or accident call CHEMTREC
(800) 424-9300, day or night
Product Identication
Product Name: IceRock
Common Name(s): Mineral Wool
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 2 of 6
Inhalation: If unconscious place in recovery position and seek medical advice. If
symptoms persist, call a physician.
Eye Contact: Remove contact lenses. Protect unharmed eye. If eye irritation persists,
consult a specialist.
Ingestion: Keep respiratory tract clear. Never give anything by mouth to an unconscious
person. If symptoms persist, call a physician.
Protection of rst-aiders: Do not leave the victim unattended.
5. FIRE FIGHTING MEASURES
Hazardous combustion products: No hazardous combustion products are known
Specic extinguishing methods: Standard procedure for chemical res.
Special protective equipment for reghters: Wear self contained breathing apparatus for
re ghting if necessary.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures: Avoid dust
formation.
Methods and materials for containment and cleaning up: Pick up and arrange disposal
without creating dust. Sweep up and shovel. Keep in suitable, closed containers for
disposal.
7. HANDLING AND STORAGE
Advice on safe handling: For personal protection see section 8. Smoking, eating and
drinking should be prohibited in the application area.
Conditions for safe storage: Keep in a dry, cool place.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Components with workplace control parameters
Components CAS-No. Form of
exposure
Permissible
concentration
Basis Update
Mineral wool bres 65997-17-3 TWA 1 bre/cm3 ACGIH
(2010-03-01)
non-durable glass wool ber 65997-17-3 TWA 1 bre/cm3 ACGIH
(2010-03-01)
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 3 of 6
*Any OSHA PELs with Issue Date 1989: Vacated by court of appeals in 1992.
PERSONAL PROTECTIVE EQUIPMENT
Respiratory protection: No personal respiratory protective equipment normally required.
Hand protection
Remarks: For prolonged or repeated contact use protective gloves.
Eye protection: Safety glasses
Skin and body protection: If used and stored as directed, no special protective
equipment is necessary.
Hygiene measures: Handle in accordance with good industrial hygiene and safety
practice. Written instructions for handling must be available at the work place.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: bres
Color: brown
Odor: odorless
Odor Threshold: no data available
pH: not applicable
Melting point/freezing point: > 1,150 °C
Boiling point/boiling range: not applicable
Flash point: not applicable
Evaporation rate: not applicable
Flammability (solid, gas): no data available
Upper explosion limit: not applicable
Lower explosion limit: not applicable
Vapor pressure: not applicable
Relative vapor density: not applicable
Relative density: no data available
Solubility(ies)
Water solubility: insoluble
Solubility in other solvents: no data available
Partition coefcient: n-octanol/water: no data available
Auto-ignition temperature: no data available
Thermal decomposition: no data available
Viscosity
Viscosity, dynamic: no data available
Viscosity, kinematic: no data available
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 4 of 6
10. STABILITY AND REACTIVITY
Reactivity: No decomposition if stored and applied as directed.
Chemical stability: Formaldehyde may be released by partial hydrolysis of the urea
formaldehyde polymer, especially in high temperature applications or
Possibility of hazardous reactions: Stable under recommended storage conditions. No
hazards to be specially mentioned.
Conditions to avoid: no data available
11. TOXICOLOGICAL INFORMATION
Acute toxicity
Product
Acute oral toxicity: Acute toxicity estimate: > 5,000 mg/kg
Method: Calculation method
Skin corrosion/irritation: no data available
Serious eye damage/eye irritation: no data available
Respiratory or skin sensitization: no data available
Germ cell mutagenicity: no data available
Carcinogenicity
IARC No component of this product present at levels greater than or equal to
0.1% is identied as probable, possible or conrmed human carcinogen
by IARC.
OSHA No component of this product present at levels greater than or equal to
0.1% is maintained in the OSHA Hazard Communication standard (29 CFR
1910.1200) and sections 1910.1001-1052.
NTP No component of this product present at levels greater than or equal to
0.1% is identied as a known or anticipated carcinogen by NTP.
Reproductive toxicity: no data available
STOT - single exposure: no data available
STOT - repeated exposure: no data available
Aspiration toxicity: no data available
Further information
Product
no data available
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 5 of 6
12. ECOLOGICAL INFORMATION
Ecotoxicity: no data available
Persistence and degradability: no data available
Bioaccumulative potential: no data available
Mobility in soil: no data available
Results of PBT and vPvB assessment: no data available
Other adverse effects
Product:
Additional ecological information: no data available
13. DISPOSAL CONSIDERATIONS
Contaminated packaging: Empty containers should be taken to an approved waste
handling site for recycling or disposal. Packaging that cannot be reused after cleaning
must be disposed or recycled in accordance with all federal, national and local
regulations.
14. TRANSPORT INFORMATION
International transport regulations
15. REGULATORY INFORMATION
OSHA Hazards: Carcinogen
EPCRA - Emergency Planning and Community Right-to-Know Act
CERCLA Reportable Quantity
Components CAS-No. Component RQ (lbs) Calculated product RQ (lbs)
Formaldehyde 50-00-0 100 *
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 304 Extremely Hazardous Substances Reportable Quantity
Components CAS-No. Component RQ (lbs) Calculated product RQ (lbs)
Formaldehyde 50-00-0 100 *
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 302: SARA 302: No chemicals in this material are subject to the reporting
requirements of SARA Title III, Section 302.
SARA 313: SARA 313: This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis) reporting
levels established by SARA Title III, Section 313.
IceRock
Safety Data Sheet
MSDS Number: INS-06-SP
Revision Date: 5-25-16
Page 6 of 6
US STATE REGULATIONS
Massachusetts Right To Know
formaldehyde 50-00-0 0 - 0.1 %
Pennsylvania Right To Know
Mineral wool bres 65997-17-3 50 - 70 %
Urea, polymer with formaldehyde 9011-05-6 10 - 20 %
non-durable glass wool ber 65997-17-3 5 - 10 %
formaldehyde 50-00-0 0 - 0.1 %
New Jersey Right To Know
Mineral wool bres 65997-17-3 50 - 70 %
Urea, polymer with formaldehyde 9011-05-6 10 - 20 %
non-durable glass wool ber 65997-17-3 5 - 10 %
California Prop 65 WARNING! This product contains a chemical
known to the State of California to cause cancer.
Mineral wool bres 65997-17-3
formaldehyde 50-00-0
The components of this product are reported in the following inventories:
TSCA On TSCA Inventory
DSL All components of this product are on the
Canadian DSL.
16. OTHER INFORMATION
Disclaimer:
Although reasonable care has been taken in the preparation of this document, we
extend no warranties and make no representations as to the accuracy or completeness
of the information contained herein, and assume no responsibility regarding the suitability
of this information for the user’s intended purposes or for the consequences of its use.
Individuals should make a determination as to the suitability of the information for their
particular purpose(s).
Needle Mat
Safety Data Sheet
MSDS Number: INS-23-SP
Revision Date: 5-25-16
Page 1 of 4
1. PRODUCT AND COMPANY IDENTIFICATION
2. HAZARDS IDENTIFICATION
Route of Entry: This material may enter the body through inhalation of nuisance dust.
Target Organs: Respiratory system
Inhalation: Sore, raspy throat
Skin Contact: Redness and possible rash; itching
Eye Contact: Itching and redness
Ingestion: N/A
NFPA: Health = 1, Fire = 0, Reactivity = 0
HMIS III: H1/F0/PH0
GHS Signal Word:
WARNING
GHS Classications:
Health, Skin corrosion/irritation, 2
Health, Serious Eye Damage/Eye Irritation, 2 B
Health, Specic target organ toxicity - Single exposure, 3
Health, Respiratory or skin sensitization, 1 Skin
GHS Phrases:
H315 - Causes skin irritation
H320 - Causes eye irritation
H335 - May cause respiratory irritation
H317 - May cause an allergic skin reaction
GHS Precautionary Statements:
P103 - Read label before use.
P264 - Wash _ thoroughly after handling.
P333+313 - If skin irritation or a rash occurs: Get medical advice/attention.
Company Identication
UniTherm International Inc.
711 Jones Street
Lewisville, Texas 75057
EMERGENCY TELEPHONE NUMBER:
For emergency involving spill, leak, re,
exposure, or accident call CHEMTREC
(800) 424-9300, day or night
Product Identication
Product Name: Needle Mat
Common Name(s): Insulation Mat
Needle Mat
Safety Data Sheet
MSDS Number: INS-23-SP
Revision Date: 5-25-16
Page 2 of 4
P337 - If eye irritation persists: _
P337+313 - Get medical advice/attention.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Ingredients:
Fibrous Glass (CAS 65997-17-3)
OSHA PEL: 15 milligrams per cubic meter of air (total); 5 milligrams per cubic meter of air
(respirable)
ACGIH TLV: 1 ber per cubic centimeter of air
4. FIRST AID MEASURES
Inhalation: Remove person to fresh air. If condition persists, seek medical attention.
Skin Contact: Rinse with copious quantities of cool water. If rash or itching persists, seek
medical attention.
Eye Contact: Rinse with water. Do not rub eyes. Seek medical attention.
Ingestion: Not applicable.
5. FIRE FIGHTING MEASURES
Flash Point (Method Used): >250 C by TOC Flammable Limits
LEL: N/A UEL: N/A
Extinguishing Media: Water, carbon dioxide, or dry chemical
Special Fire Fighting Procedures: Thermal decomposition of ber coating may produce
an irritating mixture of smoke and fumes.
Unusual Fire and Explosion Hazards: None
6. ACCIDENTAL RELEASE MEASURES
Material is a solid in roll form. If accidently released, rewind material back onto roll.
7. HANDLING AND STORAGE
Handling Precautions: Use adequate material handling equipment.
Storage Requirements: Store in dry place. Use may be at temperature extremes based on
product data, but storage should be at ambient temperature.
Needle Mat
Safety Data Sheet
MSDS Number: INS-23-SP
Revision Date: 5-25-16
Page 3 of 4
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering Controls: Local exhaust; dust collection
Personal Protective Equip: HMIS PP, B | Safety Glasses, Gloves
Safety glasses; cotton gloves; long sleeve clothing
Wash thoroughly with soap and water after handling.
9. PHYSICAL AND CHEMICAL PROPERTIES
Appearance: Fibrous Matting
Physical State: Solid
Spec Grav. /Density: 2.5
Boiling Point: N/A
Vapor Pressure: N/A
pH: N/A
Odor: No Odor
Solubility: Negligible
Freezing/Melting Pt.: 700+ °C (1292 + °F)
Vapor Density: N/A
10. STABILITY AND REACTIVITY
Stability: Material is stable.
Conditions to Avoid: None known.
Materials to Avoid: Strong-oxidizing agents.
Hazardous Decomposition: Carbon monoxide; carbon dioxide
Hazardous Polymerization: Will Not Occur.
11. TOXICOLOGICAL INFORMATION
OSHA classies brous glass as a nuisance dust. Many studies have been conducted
to determine long-term effects of brous glass inhalation. Although inconclusive, some
research indicated manufacturing employees rst employed more than 30 years ago in
factories that manufactured glass wool and mineral wool have increased rates of lung
cancer, compared to certain other reference populations. Further study is planned to
identify those factors associated with the reported increased rate. Similar ndings were
not reported regarding employees in textile ber manufacturing plants. Animal studies
have not demonstrated an increased rate of lung cancer when the animals breathed
large quantities of glass bers. Articial implantation or injection of ne glass bers into the
chest, abdominal cavity or trachea of laboratory animals has produced cancer.
12. ECOLOGICAL INFORMATION
No known hazards except for airborne bers caused by nuisance dust. 10 milligrams per
cubic meter for ber diameters less than 7 microns.
Needle Mat
Safety Data Sheet
MSDS Number: INS-23-SP
Revision Date: 5-25-16
Page 4 of 4
13. DISPOSAL CONSIDERATIONS
Incineration preferred in a federal, state, or local approved facility.
14. TRANSPORT INFORMATION
None special required.
15. REGULATORY INFORMATION
COMPONENT / (CAS/PERC) / CODES
None known
16. OTHER INFORMATION
Disclaimer:
Although reasonable care has been taken in the preparation of this document, we
extend no warranties and make no representations as to the accuracy or completeness
of the information contained herein, and assume no responsibility regarding the suitability
of this information for the user’s intended purposes or for the consequences of its use.
Individuals should make a determination as to the suitability of the information for their
particular purpose(s).
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 1 of 6
1. PRODUCT AND COMPANY IDENTIFICATION
2. HAZARDS IDENTIFICATION
Emergency Overview
The hazards of this product are associated mainly with its processing. Dust may form
explosive mixture in air. High concentrations of dust can irritate eyes, nose and respiratory
system and cause coughing and sneezing. Processing meta-aramid products can
release Dimethyl Acetamide (DMAC). Hazards related to DMAC include: May be harmful
by inhalation (after often repeated exposure). May be harmful in contact with skin
(after often repeated exposure). Liver and kidney injuries may occur. Processing para-
aramid products can release respirable dust and respirable bre particulate. Prolonged
inhalation of respirable dust and respirable bre particulate at high concentrations can
cause lung damage. Continual rubbing of bre particulates and dust on the skin can
cause a transitory, mild irritation with redness or itching.
Potential Health Effects
Carcinogenicity
None of the components present in this material at concentrations equal to or greater
than 0.1% are listed by IARC, NTP, or OSHA, as a carcinogen.
3. COMPOSITION/INFORMATION ON INGREDIENTS
Component CAS-No. Concentration
Meta-aramid ber or meta-aramid ber blended with
para-aramid, antistatic or other synthetic bers
100 %
Exposure limits may be applicable for the following:
Meta-aramid 25765-47-3
Para-aramid 26125-61-1
Synthetic bres
N,N-Dimethylacetamide 127-19-5
Company Identication
UniTherm International Inc.
711 Jones Street
Lewisville, Texas 75057
EMERGENCY TELEPHONE NUMBER:
For emergency involving spill, leak, re,
exposure, or accident call CHEMTREC
(800) 424-9300, day or night
Product Identication
Product Name: Black Nomex Thread
Common Name(s): Nomex Aramid Fire
Retardant Thread, Nomex Sewing Thread
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 2 of 6
4. FIRST AID MEASURES
General advice: No hazards, which require special rst aid measures. If symptoms persist,
call a physician. If irritation occurs, ush area thoroughly with water.
5. FIRE FIGHTING MEASURES
Flammable Properties
Flash point: not applicable
Thermal decomposition: > 300 °C (> 572 °F)
Fire and Explosion Hazard: Hazardous decomposition products formed under re
conditions.
Extinguishing Media: Use extinguishing measures that are appropriate to local
circumstances and the surrounding environment.
Fireghting Instructions: Wear self contained breathing apparatus for re ghting if
necessary.
6. ACCIDENTAL RELEASE MEASURES
NOTE: Review FIRE FIGHTING MEASURES and HANDLING (PERSONNEL) sections before
proceeding with clean-up. Use appropriate PERSONAL PROTECTIVE EQUIPMENT during
clean-up.
Safeguards (Personnel): None.
Spill Cleanup: Avoid dust formation. Clean up dusts and bres with high efciency
particulate air (HEPA) ltered vacuum equipment, or by wet cleaning.
Accidental Release Measures: Do not let product enter drains.
7. HANDLING AND STORAGE
Handling (Personnel): Avoid dust formation. Do not touch moving threadlines.
Entanglement with this bre can severely cut or even sever ngers. Avoid breathing dust
or vapor.
Storage: Keep away from direct sunlight.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Engineering controls: Ensure adequate ventilation. Recirculated air should be ltered to
remove respirable dust. Provide for appropriate exhaust ventilation and dust collection at
machinery. Static charges can cause explosions in solvent and dust laden atmospheres.
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 3 of 6
Provide grounding of equipment to prevent static build-up.
Personal protective equipment
Eye protection: Safety glasses with side-shields
Respiratory protection: When workers are facing concentrations above the exposure
limit they must use appropriate certied respirators.
Exposure Guidelines
Exposure Limit Values
Meta-aramid
AEL * (DUPONT) 10 mg/m3 8 hr. TWA Total dust.
AEL * (DUPONT) 5 mg/m3 8 hr. TWA Respirable dust.
Para-aramid
AEL * (DUPONT) 2 bers/cm3 8 & 12 hr. TWA Respirable bers.
AEL * (DUPONT) 5 mg/m3 8 & 12 hr. TWA Non-brous particulate
and/or nonrespirable
bres.
N,N-Dimethylacetamide
PEL (OSHA) 10 ppm 35 mg/m3 8 hr. TWA
Skin designation applies.
Skin designation applies.
TLV (ACGIH) 10 ppm TWA
AEL * (DUPONT) 10 ppm 8 & 12 hr TWA Skin
* AEL is DuPont’s Acceptable Exposure Limit. Where governmentally imposed
occupational exposure limits, which are lower than, the AEL are in effect, such limits shall
take precedence.
9. PHYSICAL AND CHEMICAL PROPERTIES
Form: Nonwoven fabric, woven fabric, bres, yarn
Color: Black, pigmented
Odor: None
Melting point/range: N/A
Specic Gravity: 1.38
Water solubility: Insoluble
10. STABILITY AND REACTIVITY
Conditions to avoid: Temperature > 200 °C (> 392 °F).
Heating can release hazardous gases.
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 4 of 6
Incompatibility: Strong acids and strong bases
Decomposition: Decomposition temperature: > 300 °C (> 572 °F).
Hazardous decomposition products Carbon monoxide, nitrogen
oxides (NOx), Hydrogen cyanide (hydrocyanic acid).
11. TOXICOLOGICAL INFORMATION
Skin sensitization: Did not cause sensitization on laboratory animals.
Negative in human patch test.
Meta-aramid
Oral ALD: > 11,000 mg/kg, rat
Inhalation ALC: > 238 mg/m3, rat
lung effects
Skin irritation: non-irritant
Carcinogenicity: Did not show carcinogenic effects in animal experiments.
Para-aramid
Oral ALD: > 7,500 mg/kg, rat
Skin irritation: Species: rabbit, No skin irritation
non-irritant
Eye irritation: non-irritant
Repeated dose toxicity: Inhalation, rat
lung effects
Carcinogenicity: Animal testing did not show any carcinogenic effects.
Mutagenicity: Tests on bacterial or mammalian cell cultures did not show
mutagenic effects.
N,N-Dimethylacetamide
Dermal LD50: 2,240 - 9,600 mg/kg, animals (unspecied species)
Oral LD50: 3,000 - 6,000 mg/kg, rat
Inhalation 1 h LC50: 8.81 mg/l female, rat
Value applicable only if respirable particles are formed.
Inhalation 4 h LC50: 2.2 mg/l female, rat
Skin irritation: Species: rabbit
Mild skin irritation
Eye irritation: Species: rabbit
irritant
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 5 of 6
Repeated dose toxicity: Dermal
Central nervous system depression, Liver effects, Skin
effects
Oral
Pathologic changes, Stomach, Testes, Liver, Kidney,
Abnormal decrease in number of red blood cells
(anaemia)
Inhalation
Kidney effects, Liver effects, Retinal damage
Carcinogenicity: Did not show carcinogenic effects in animal experiments.
Mutagenicity: Did not cause genetic damage in cultured bacterial cells.
Did not cause genetic damage in cultured mammalian
cells. Evidence suggests this substance does not cause
genetic damage in animals.
Toxicity to reproduction: Animal testing showed no reproductive toxicity.
Teratogenicity: Animal testing showed effects on embryo-foetal
development at levels equal to or above those causing
maternal toxicity.
12. ECOLOGICAL INFORMATION
Aquatic Toxicity
Para-aramid: This product has no known eco-toxicological effects.
N,N-Dimethylacetamide 96 h LC50: Fathead minnow 1,500 mg/l
13. DISPOSAL CONSIDERATIONS
Waste Disposal: Can be landlled or incinerated, when in compliance with local
regulations. Do not ush into surface water or sanitary sewer system.
14. TRANSPORT INFORMATION
None special required.
15. REGULATORY INFORMATION
TSCA Status: Product is an article as dened at 40CFR720.3(c) and is not subject to TSCA
Inventory requirements.
SARA 313 Regulated Chemical(s): SARA 313: This material does not contain any chemical
components with known CAS numbers that exceed the threshold (De Minimis) reporting
levels established by SARA Title III, Section 313.
California Prop. 65: Chemicals known to State of California to cause cancer, birth defects
or any other harm: none known
Black Nomex Thread
Safety Data Sheet
MSDS Number: THRD-08-SP
Revision Date: 5-25-16
Page 6 of 6
16. OTHER INFORMATION
Disclaimer:
Although reasonable care has been taken in the preparation of this document, we
extend no warranties and make no representations as to the accuracy or completeness
of the information contained herein, and assume no responsibility regarding the suitability
of this information for the user’s intended purposes or for the consequences of its use.
Individuals should make a determination as to the suitability of the information for their
particular purpose(s).
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

UniTherm IE0245 Operating instructions

Type
Operating instructions

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI