Rust-Oleum Automotive 311281 User manual

Brand: Rust-Oleum Automotive

Model: 311281

Type: User manual

This manual is also suitable for

TECHNICAL DATA PCG-08

PEEL COAT

RUGGED COAT

Form: GDH-1226

Rev.: 112816

.DESCRIPTION AND USES .

Rust-Oleum

Peel Coat

Rugged Coat is a textured, removable

coating that creates a rugged, exterior look and protection from

scratches and road debris. This premium formula is easy to peel,

safe to wash and can be applied to metal, plastic, chrome, glass

and other surfaces. Peel Coat is a temporary coating that's

designed to last for 6 months.

.PRODUCTS .

SKU Description

311281 Rugged Coat Black

311282 Rugged Coat Sand

311283 Rugged Coat Red

311284 Rugged Coat Blue

..PRODUCT APPLICATION .

PAINTING CONDITIONS

Use outdoors or in a well ventilated area such as an open

garage. Use when temperature is between 50-90°F (10-

32°C) and humidity is below 65% to ensure proper drying.

Do not apply to galvanized metal. Avoid spraying in very

windy and dusty conditions. Cover surrounding area to

protect from spray mist.

SURFACE PREPARATION

Wash the surface with a commercial detergent or soap

and water prior to the application

..PRODUCT APPLICATION (cont.) .

APPLICATION

Shake can vigorously for one minute after the mixing ball

begins to rattle. If mixing ball fails to rattle DO NOT

STRIKE CAN. Contact Rust-Oleum. Shake often during

use. Hold can 14-20" from surface and spray in a steady

back-and-forth motion, slightly overlapping each stroke.

Keep the can the same distance from the surface and in

motion while spraying. Target 50% coverage on the first

coat. Apply 4 or more light coats to build desired coating

thickness and ensure coats are sufficiently dried before

moving to the next maximize texture. For best results,

apply 1 more final coat using short burst sprays. Allow

coating to dry for about 10 minutes between coats. More

coats will result in a thicker coating which is easier to

remove when desired. Allow the coating to cure for 24

hours before washing. Do not use near open flame.

DRY & RECOAT

Dry and recoat times are based on 70°F (21°C) and 50%

relative humidity. Allow more time at cooler temperatures.

Dries to the touch in 20 minutes and can be handled in 1

hour.

REMOVAL

The film can be peeled off once the coating has fully cured. This

coating has been formulated for temporary use and is

recommended to be removed within 6 months or less. A

microfiber cloth or mineral spirits may assist in the removal of

coating in intricate areas.

CLEAN-UP

When finished spraying, clear the spray valve by turning

can upside down and pushing the button for 5 seconds.

Allow wet paint to dry and once dry, peel away or clean up

wet paint with mineral spirits. Properly discard empty

container. Do not burn or place in home trash compactor.

CLOGGING

If the valve clogs, twist and pull off spray tip and rinse in a

solvent such as mineral spirits. Do not insert any object

into can valve opening.

TECHNICAL DATA

PEEL COAT

RUGGED COAT

Rust-Oleum Corporation Form: GDH-1226

11 Hawthorn Parkway Phone: 877•385•8155 Rev.: 112816

Vernon Hills, Illinois 60061 www.rustoleum.com

An RPM Company

PHYSICAL PROPERTIES .

PEEL COAT RUGGED COAT

Resin Type

Synthetic Rubber

Pigment Type

Varies with color

Solvents

Blend of Acetates, Aliphatic and Aromatic Hydrocarbons

MIR

1.33 Max

Fill Weight

11 ounces

Recommended Dry Film

Thickness (DFT) Per Coat

0.5-1.0 mils (per coat)

(12.5-25µ per coat)

Practical Coverage

at Recommended DFT

8 sq.ft./can

(0.75 m

/can)

Dry Times at 70-80°F

(21-27°C) and 50%

Relative Humidity

Touch

20 minutes

Handle

1 hour

Recoat

20 minutes

Dry Heat Resistance

200°F (93°C)

Shelf Life

3 years

Flash Point

-156°F (-104°C)

Safety Information

For additional information, see SDS

The technical data and suggestions for use contained herein are correct to the best of our knowledge, and offered in good faith. The statements of this literature

do not constitute a warranty, express, or implied, as to the performance of these products. As conditions and use of our materials are beyond our control, we

can guarantee these products only to conform to our standards of quality, and our liability, if any, will be limited to replacement of defective materials. All