NICOR Lighting STP-10-120-WH-PC Installation guide

NICOR Lighting
Brand
NICOR Lighting
Model
STP-10-120-WH-PC
Category
Motorcycle Accessories
Type
Installation guide

NICOR Lighting STP-10-120-WH-PC is a LED Mini Step Light designed for wet locations, both indoors and outdoors. It features a compact design and can be installed within 1.2m (4ft) of the ground. The fixture is easy to install, requiring only a single gang box and basic wiring. It comes with interchangeable face plates for vertical or horizontal mounting, and the photocell must be installed at the top of the fixture for both orientations. The STP-10-120-WH-PC operates on AC120V 60Hz power supply and provides reliable starting and protection against electrical shocks.

NICOR Lighting STP-10-120-WH-PC is a LED Mini Step Light designed for wet locations, both indoors and outdoors. It features a compact design and can be installed within 1.2m (4ft) of the ground. The fixture is easy to install, requiring only a single gang box and basic wiring. It comes with interchangeable face plates for vertical or horizontal mounting, and the photocell must be installed at the top of the fixture for both orientations. The STP-10-120-WH-PC operates on AC120V 60Hz power supply and provides reliable starting and protection against electrical shocks.

1) WARNING: RISK OF SHOC
K
Electric current can cause serious injury unless handled properly. For your safety always remember to:
-Turn off the power supply at the fuse or circuit breaker box before you install the fixture.
-Turn off the power supply again when you change lamps or perform other maintenance.
-Ground the fixture to avoid potential electric shocks and to ensure reliable starting.
-Double check all connections to be sure they are all tight and correct.
-Wear rubber-soled shoes and work on a sturdy wooden ladder.
2
)
This fixture is desi
g
ned for use in a circuit
p
rotected b
y
a fuse or circuit breaker. It is also desi
g
ned
to be installed in accordance with local electrical codes. If
y
ou are unsure about the wirin
g
,
consult a
q
ualified electrician and check
y
our local electrical code
.
3
)
Account for small
p
arts and destro
y p
ackin
g
material, as these ma
y
be hazardous to children
.
4) WARNING: RISK OF FIRE
Wire must be suitable for at least 60°C . Consult a qualified electrician before installing.
5) Installation environment : suitable for wet location (caulking around the face plate is required),
able to install inside power box of shelter, indoors or outdoors.
6) Installation postion : install within1.2m (4ft) of the ground.
7) This unit is to be used at AC120V 60Hz power supply only.
8) Make sure the louver always faces down when installing this fixture.
1
)
Connect House Black
(
HOT
)
wire to Black
(
LINE
)
wire with connector.
Connect House White
(
Neutral
)
wire to White
(
NEUTRAL
)
wire with connector
Connect Green
/Yellow
wire to Bare
(g
round
)
wire with connecto
r
2
Insert Fixture into the Wall Sin
le-Gan
Box. Secured with mountin
screws
2
.
3
)
Choose either the *Vertical or Horizontal Face Plate. Secure to the bracket
.
4) Turn Power On.
INSTALLATION INSTRUCTIONS
PREPARATION OF LIGHT FIXTURE FOR INSTALLATION
WARNINGS AND SAFETY PRECAUTIONS
S
LED MINI STEP LIGHT
IMPORTANT SAFETY INFORMATION
FOR YOUR PROTECTION, READ CAREFULLY
GREEN/YELLOW
GROUND(GREEN/YELLOW)
STP-10-120-WH
STP-10-120-WH-PC
CAUTION: For your safety and proper operation of this fixture, read instructions
carefully before you start. Note and understand all safety information in bold print.
(*If installing STP-120-WH-PC, align photocell opening on faceplate to photocell on fixture.)
WARNING: Before wiring to the power supply, turn off the electricity at fuse or circuit breaker box. Ensure grounding
to avoid potential electrical shock and to ensure reliable lamp starting. INSTALL THIS FIXTURE ONLY IN A SINGLE
GANG BOX. STP-120-WH-PC MUST BE INSTALLED WITH PHOTOCELL AT TOP OF FIXTURE FOR BOTH
HORIZONTAL AND VERTICAL PRODUCTS.
  • Page 1 1

NICOR Lighting STP-10-120-WH-PC Installation guide

NICOR Lighting
Brand
NICOR Lighting
Model
STP-10-120-WH-PC
Category
Motorcycle Accessories
Type
Installation guide

NICOR Lighting STP-10-120-WH-PC is a LED Mini Step Light designed for wet locations, both indoors and outdoors. It features a compact design and can be installed within 1.2m (4ft) of the ground. The fixture is easy to install, requiring only a single gang box and basic wiring. It comes with interchangeable face plates for vertical or horizontal mounting, and the photocell must be installed at the top of the fixture for both orientations. The STP-10-120-WH-PC operates on AC120V 60Hz power supply and provides reliable starting and protection against electrical shocks.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents