RAIN GUARD CR-0613PK User manual

Brand: RAIN GUARD

Model: CR-0613PK

Type: User manual

This manual is also suitable for

CR-0612

RAIN GUARD CR-0613PK is a water-based, silane/siloxane graffiti & water repellent that combines high-quality penetrating chemical solids with an acrylic surface treatment component, to create a clear, deep-penetrating, and non-film-forming chemically-reactive masonry water repellent that contains no silicone oils, paraffin wax, or urethanes.

This material is Ready To Use - Do Not Dilute. It provides superior grade, heavy-duty graffiti and water-repellent performance on a wide variety of vertical surfaces. It is mold and mildew resistant, and its protection is not affected by weathering or UV light. It is also breathable, which means that it does not trap moisture.

Manufactured by:

RAINGUARD INTERNATIONAL

1201 Dove Street, Suite 625, Newport Beach, CA 92660

Tel 949.515.8800 Fax 949.675.3450

[email protected] www.rainguard.com

Page 1

BLOK-LOK™ With Graffiti Control with

VandlClean Graffiti Cleaner

COVERAGE RATES (THEORETICAL):

All Substrates___ Sq Ft/ Gallon

Two Coats average 100

Special Considerations:

 Use of fluted or scored block or raked joints will in-

crease surface areas by 20%-30% or more and de-

crease coverage rates. Allow for this increased sur-

face area when determining material requirements.



Extremely porous surfaces may require multiple

coats.

Warranty Period:

Water Repellency—10 years

Graffiti Protection— 2 years

Division 3, 4, 7 & 9

CR-0620

CSI Reference:

art Number:

 Exclusive MICRO-LOK formulation

 Mold and Mildew Inhibitor

 Protection not effected by weathering or UV light

 Single product provide protection against water and graffiti

 V.O.C. compliant

 Contains no known carcinogens

 Does not darken surfaces

 Breathable – does not trap moisture

Use and Care Manual

PRODUCT DESCRIPTION

Rainguard BLOK-LOK with Graffiti Control is a water-based, silan-

e/siloxane graffiti & water repellent that combines high-quality

penetrating chemical solids with an acrylic surface treatment com-

ponent, to create a clear, deep-penetrating, and non-film-forming

chemically-reactive masonry water repellent that contains no sili-

cone oils, paraffin wax, or urethanes.

MICRO-LOK creates a micro-molecular chemical and mechanical

bond between the water-repellent chemicals and the

substrate. BLOK-LOK penetrates deep into porous masonry

surfaces to pro-vide long-lasting and virtually indestructible

water-repellent pro-tection that is not affected by weather or

sunlight. The acrylic surface component make graffiti easy to

remove with Rainguard’s VandlClean Graffiti Cleaner.

BLOK-LOK provides superior grade, heavy-duty graffiti and water-

repellent performance on a wide variety of vertical surfaces. This

material is Ready To Use - Do Not Dilute.

PRODUCT FEATURES:

RECOMMENDED USES:

 Bare wood

 Brick

 Concrete

 EFIS or cement plaster

 Masonry block

 Stucco

 Porous stone

 Unglazed tile

PRECAUTIONS & LIMITATIONS

All surfaces to be coated should be clean of any

dirt and grime, efflorescence, lime run, form oils

and release agents, grease, mud, excess mortar, and

mold and mildew, etc. All cracks should be pointed

or caulked. All voids, bee holes, masonry surface

de-fects, and openings such as conduits, pipes,

drains, door frames, vents, air conditioner

openings, electrical openings, control joints, or any

dissimilar materials should be repaired using

urethane or other approved patching. May be

applied to fresh concrete after 48 hours.

DO NOT DILUTE.

BLOK-LOK with Graffiti Control IS

SUPPLIED READY TO USE.

Page 2

Silane/Siloxane

100%

40%

Milky White

Slight Ammonia Odor

<15 g/L V.O.C. Compliant

Non-Flammable

Approximately 7.5

9.6 Seconds No. 4 Ford Cup

Approximately 8.7 lbs./gal.

Approx 1 Hour

5 to 7 days

ASTM E-514-86 98.7% Leak Red

TECHNICAL DATA

Material Type

Active Content

Volume Solids

Color of Material

Odor

V.O.C.

Flash Point

pH Value

Viscosity

Weight

Surface Dry/Recoat

Full Chemical Cure

TEST DATA

Wind Driven Rain

Water Pen Fed Spec

SS-W-110C 75% Min Req

96.8% Leak Red Chloride Ion Intr

Salt Ponding NCHRP No. 244 Allowed 25% - Obtained 13.0%

Water Abs CMU ASTM C140-75 89% Effective

Water Vapor Trans ASTM D-1653 100% Vapor Perm

Water Repellency ASTM C67-80A 97% Effective

Weathering ASTM G-53

2500 Hours – N

o Change

Surface Burning ASTM E84 Flame Spread 0, Smoke developed 0

LIMITED WARRANTY PROCEDURES/INFORMATION The

information contained herein is offered in good faith and is

believed to be accurate. To be eligible for a Rainguard Warranty

the following must occur:

1. A site visit must be conducted by an employee or agent of

Rainguard and a Field Inspection Report completed.

2. A Warranty Application must be fully completed by the

applicator.

3. Field Inspection Report, Warranty Application, and a copy

of the distributor’s invoice must be submitted to and ap-

proved by Rainguard.

This material is only warranted when applied in accordance with

the manufacturer’s guidelines and warranty procedures. With-

out adherence to these specific guidelines, no expressed or im-

plied warranty of this product is given. Please contact Rainguard

for additional information.

PRECAUTIONS & LIMITATIONS

Do not apply to surfaces if moisture content is greater than

22% as measured with an electronic moisture meter. Do not

apply materials in climates where freezing temperatures have

existed prior to application. Allow adequate time for surfaces

to thaw. Establish that air, surface, and material temperatures

are above 35°F (2°C) and at least 5°F above the dew point prior

to painting. Do not apply at temperatures below 35°F or when

temperatures are expected to drop below 35°F within 48 hours

of application. Do not apply if rain, snow, or lower

temperatures are expected within 48 hours. Do not apply if

relative humidity is greater than 80%.

Use material in a well-ventilated area. Protect the work of

other trades. Protect shrubbery and other plants with drop

cloths. Pro-tect automobiles and all other areas not to be coated

from over-spray. Remove overspray from any windows,

automobiles, metal, etc. as soon as possible should it occur.

To prevent permanent staining, clean spills or leaks in a timely

manner.

Store materials in a well-protected area between 45° and 90°

F. Avoid freezing temperatures, direct sunlight, and moisture.

Keep away from heat sources.

TEST PANEL

Always apply material to a mock wall or test panel. Test wall or

actual surface area to determine acceptable color, surface

po-rosity, application rates, and methods before starting

general application.

FOLLOW THESE SIMPLE STEPS

1. BLOK-LOK wi

th Graffiti Control should be applied using low-

pressure airless spray equipment.

2. Avoid atomizing material by using a spray tip size of .035

to .051. Spray head should be held 8 to 12 inches from the

surface so that the flood coat runs down the wall approxi-

mately 6-12 inches below the point of application.

3. Avoid application in windy weather.

4. Trigger gun off at the end of each pass to avoid using exces-

sive materials. Stop all applications only at corners, joints,

seams, or edges.

5. Apply second coat wet on wet after first coat has been al-

lowed to penetrate for 5 minutes. Immediately roll or brush

out runs and drips to ensure even appearance.

VandlClean Graffiti Cleaner

Product Description:

Rainguard VANDLCLEAN Graffiti cleaner is an environmentally-friendly, biodegradable graffiti cleaner de-signed to

dissolve spray paint, marker, pen, pencil, ink, or glue. It is 100% water-neutralized (neutralized with wa-ter) and

is safe for use near waterways, rivers, canals, and reservoirs. VANDLCLEAN Graffiti Cleaner is a citrus-based,

pleasantly-scented, concentrated cleaner and degreaser designed for a wide range of cleaning chores on any

surface not harmed by water alone. Natural orange extracts coupled with biodegradable surfac-tants, dirt-

suspending agents, and builders produce a formidable cleaner for everyday applications. When com-pared with

other name brand products and other commonly used hard surface cleaners, VANDLCLEAN Graffiti Cleaner

demonstrates conclusive proof that citrus performs more efficiently and effectively. It is suitable for removing

graffiti from brick, cement, wood, or any porous surface. VANDLCLEAN Graffiti Remover may damage PVC

surfaces (plastics), so it is recommended that a small area be tested prior to use.

Application:

Non-Porous Metallic Surfaces

On previously painted surfaces, polished metal, stainless steel, aluminum, or any other type of non-porous sur-

face, spray VANDLCLEAN Graffiti Cleaner directly to the affected surface, and allow to remain until graffiti begins

to dissolve (one to two minutes). Wipe the surface clean of the graffiti.

Non-Porous Painted Surfaces

On painted surfaces, remove graffiti in small sections to ensure that the graffiti remover does not damage the

surface. In a case where the graffiti remover dissolves the underlying paint, immediately neutralize the cleaned

area with water. Use a clean section of the rag to remove any remaining graffiti residue once the majority of the

graffiti has been removed. Always wash the surface with water to neutralize the graffiti cleaner when the job is

completed.

Porous Surfaces (Brick or Concrete)

For brick or concrete surfaces, use a stiff brush to apply the graffiti remover into the porous surface. Apply the

product liberally and work the product into the porous surface using a twisting motion of the brush. Allow the

product to seep into the surface for a minimum of 20-30 minutes, then test to see if graffiti is dissolving. If graffiti

has dissolved, you may use high-pressure water to wash the graffiti from the surface. If a pressure washer is not

available, we recommend washing (scrubbing) the treated surface with warm water and an industrial-grade de-

greaser or soap. Rinse with fresh water when finished.

DO NOT USE HIGH PRESSURE WATER; DAMAGE TO SURFACE OF SUBSTRATE. MAY RESULT. IF ALL OF

THE GRAF-FITI IS NOT REMOVED IN THE FIRST ATTEMPT, PERFORM A SECOND APPLICATION WHEN

DRY. WE RECOM-MEND ROOM TEMPERATURE/WARM WATER (21°C-65°C / 70°F-150°F).

STEAM OR HOT WATER MAY DAMAGE THE SURFACE OR GROUTED AREAS.

Sandstone or Porous Concrete Surfaces

Use a stiff brush to apply the graffiti remover into porous surface. Apply the product liberally, and work the

product into the porous surface using a twisting motion of the brush. Allow the product to seep into the surface

for a minimum of 20-30 minutes, and then test to see if graffiti is dissolving.

DO NOT USE HIGH-PRESSURE WATER TO REMOVE GRAFFITI FROM THE SURFACE.

SANDSTONE IS EXTREMELY SOFT AND WILL BE DAMAGED BY HIGH-PRESSURE WATER.

We recommend washing (scrubbing) the treated surface with warm water and an industrial grade degreaser or

soap. Rinse with fresh water when finished. If shadows remain, allow surface to dry and perform a second re-

moval procedure.

Page 3

Mixing:

DO NOT DILUTE. Rainguard VANDLCLEAN Graffiti Cleaner is 100% biodegradable and neutralized in wa-ter.

Water will neutralize the cleaner, making it ineffective. Once graffiti removal is complete, the surface should

be thoroughly washed down with water to neutralize any remaining active product.

Coverage:

Coverage of the remover will vary depending on how heavily the graffiti is painted on the surface. Multiple

appli-cations may be required to completely remove graffiti. Allowing the product to remain in place long

enough will maximize the coverage of the remover.

Storage and Handling:

Rainguard VANDLCLEAN Graffiti Cleaner is non-hazardous. Keep the VANDLCLEAN Graffiti Cleaner product

in a sealed container and store in a cool, dry, well-ventilated storage in compliance with all current and

local regulations. Keep out of direct sunlight, moisture, or rain. Maintain material in sealed containers at

all times. Do not store materials in unlabeled containers. The expected shelf-life of Rainguard VANDLCLEAN

Graffiti Cleaner is 24 months from the date of manufacture if stored as indicated above, in unopened and

sealed containers. Liquid products should be agitated before use if they have been stored for an extended

period.

Precautions:

CAUTION: Contains Delimonene, surfactants, lifters, and purified water. Avoid contact with eyes and

mucus membranes. In case of contact, flush with water. In case of contact with eyes, flush with water for 15

minutes. If swallowed, give large quantities of water and seek immediate medical attention. KEEP

OUT OF REACH OF CHILDREN. VANDLCLEAN Graffiti Cleaner is an ideal product for high-pressure

or steam-cleaning appli-cations. VANDLCLEAN will keep nozzles clean and free from corrosion.

Page 4

RAIN GUARD CR-0613PK User manual

Brand: RAIN GUARD

Model: CR-0613PK

Type: User manual

This manual is also suitable for

CR-0612

Download PDF

report

RAIN GUARD CR-0613PK User manual

This manual is also suitable for

RAIN GUARD CR-0613PK User manual

Related papers

Other documents