2. Steves & Sons
  3. A6201RC-AW-WJ-6LH
A6201RC-AW-WJ-6LH

Steves & Sons A6201RC-AW-WJ-6LH Installation guide

  • Hello! I am an AI chatbot trained to assist you with the Steves & Sons A6201RC-AW-WJ-6LH Installation guide. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
Install
FIGURE A:
Caulk
Pre-hanging Plug:
Leave in place until unit
is temporarily fastened.
Pre-hanging Plug Screw:
Remove the screw
before fastening the unit.
FIGURE B:
FIGURE E:
Bottom Door Sweep
Threshold Screws:
Adjust all sill screws
half turn up or down,
only if necessary.
FIGURE C:
Security Plate
(Do not remove)
FIGURE D:
Shim at every arrow location.
(Be sure to shim
behind each hinge)
IMPORTANT: READ THE INSTRUCTIONS COMPLETELY THROUGH BEFORE BEGINNING TO INSTALL
THE DOOR UNIT.
1. PREPARE THE OPENING
• Thethreesidesoftheroughopeningmustbeinthesameplaneforproperinstallationandoperationofthedoor
(See figure A).
• Theroughframedopeningshouldbeabout1to2incheswiderandtallerthanthedoorunititself.
• Theoorareashouldbeclean,dryandlevel.Applygenerousamountsofcaulktooorwherethethresholdwill
rest (See figure A).
2.BEFOREYOUINSTALLTHEDOORUNIT
• Ifyourunithasanytypeofbraceunderthesillorskidprotectors,pleaseremoveatthispoint.
• Beforeinstallingthedoorunityoumustremovethescrewfromthepre-hangingplugbeforeyoubegininstallation
(See figure B).
• However,donotremovethepre-hangingplugitselfuntiltheunitistemporarilyfastenedinplace.ThePre-hanging
plug is necessary to hold the door closed during installation.
• Ifyourdoorunithasasecurityplatefastenedtothelockjamb,donotremoveit(SeegureC).
5.PERMANENTLYFASTENTHEUNIT
• Important:Werecommendreplacingonescrewoneachjamb-sidehingewitha3”or3-1/2”screw(notprovided)
to securely fasten the unit on the hinge side of the door unit. Be sure you have shimmed behind each hinge.
• Besureyouhaveshimmedthelocksideofthedoorunitinatleast3placesalongtheverticallockjamb(See
figure D).
• Oncealignmentiscorrect,permanentlyscrewtheunitintoplaceusing2”drywallscrews(notprovided)through
the jamb and the shims then into the stud.
3.SETTINGTHEUNIT
• Fromoutsideyourhome,centerthedoorunitintheopeningandtiltintoposition.Assureuniformspacingaround
theunit(SeegureC).
• Shimunitinplacebydrivingtheshimsfromtheinteriorside.Besuretoshimbehindeachhinge(SeegureD).
Note: shimming the header is not necessary.
• Plumbandsquareoneverticaljamb,thentemporarilyfastentheunitintoplaceusing3”drywallscrews(not
supplied).
4.CHECKFORPROPERALIGNMENT
• Plumbandsquaretheotherverticaljamb.Shimbetweenjambandroughopeningtoassureproperalignment.
Also shim behind each hinge.
• Removepre-hangplugfromtheborehole.Openandclosethedoor.Thereshouldbeuniformspacing(1/8”)
betweendoorandjambonthetwosidesandthetopofthedoor.Makeanynecessaryadjustmentstotheunit
now, to assure uniform spacing around the door, before proceeding.
• Besurethedoorsweepcontactsthethresholdevenly.Makenecessaryadjustmentsnow,beforeproceeding.
• Testtheadjustablethreshold(SeegureE).Totest,placeasheetofpaperoverthethresholdandclosethedoor
then, pull on the paper. If the threshold adjustment is correct there will be some tension on the paper as you pull it.
If the paper tears, the threshold is too high. If there is no tension at all on the paper when you pull it, the threshold
istoolow.Toadjustthethreshold,tightenorloosenallscrewsonthesill,1/2aturnatatime(lefttoloosenand
right to tighten. Then repeat the paper test. Remember you want the paper to have some tension as you pull it,
without tearing the paper.
6.COMPLETIONSTEPS
• Installlocksethardwareinaccordancewithhardwaremanufacturer’sinstructions.
• Applyinteriorandexteriorcasingormoldingasdesired.Note:Yourdoorunitmayalreadyhaveexterior
brickmoldapplied.
• Caulkaroundtheentireframe/brickmoldoftheexteriorwall,usingahighqualityexteriorgradecaulk.Caulk
wherethejambsandthresholdmeet,andontheexterioredgeofthethreshold.Thenifneededaddabeadof
caulkbetweenthejambandthethreshold(SeegureE).
• Followthepaintmanufacturer’sinstructionsforpaintingornishingthejamb.
• Removeadhesivebackingfromdustpad(includedwiththeseinstructions).
• Placedustpadrightabovethesillwiththethickeredgeundertheweather-stripping,makingsurethethinneredge
does not protrude past the jamb.
(See figure E).
• Donotpaintornishthebottomdoorsweep,weather-stripping,ordustpad.
If these pieces are painted or finished your door will not seal properly.
• Makesureyouleavethedooropenlongenoughtoensureproperdryingafterpaintingornishingthejamb.This
isimportant,wetpaintornishwillsticktotheweather-strippingthenalteritsperformance.
/