2. Steves & Sons
  3. SIP0000012211
SIP0000012211

Steves & Sons SIP0000012211 Operating instructions

  • Hello! I am an AI chatbot trained to assist you with the Steves & Sons SIP0000012211 Operating instructions. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
1. PREPARE THE OPENING
• Thethreesidesoftheroughopeningmustbeinthesameplaneforproper
installationandoperationofthedoor(SeegureA).
• Theroughframedopeningshouldbeabout1to2incheswiderandtallerthan
thedoorunititself.
• Theoorareashouldbeclean,dryandlevel.Applygenerousamountsofcaulk
tooorwherethethresholdwillrest(SeegureA).
2. BEFORE YOU INSTALL THE DOOR UNIT
• Ifyourunithasanytypeofbraceunderthesillorskidprotectors,please
removeatthispoint.
• Beforeinstallingthedoorunityoumustremovethescrewfromthepre-hanging
plugbeforeyoubegininstallation(SeegureB).
• However,donotremovethepre-hangingplugitselfuntiltheunitistemporarily
fastenedinplace.ThePre-hangingplugisnecessarytoholdthedoorclosed
duringinstallation.
• Ifyourdoorunithasasecurityplatefastenedtothelockjamb,donotremoveit
(SeegureC).
5. PERMANENTLY FASTEN THE UNIT
• Important:Werecommendreplacingonescrewoneachjamb-sidehingewitha
3"or3-1/2"screw(notprovided)tosecurelyfastentheunitonthehingeside
ofthedoorunit.Besureyouhaveshimmedbehindeachhinge.
• Besureyouhaveshimmedthelocksideofthedoorunitinatleast3places
alongtheverticallockjamb(SeegureD).
• Oncealignmentiscorrect,permanentlyscrewtheunitintoplaceusing2"dry
wallscrews(notprovided)throughthejambandtheshimsthenintothestud.
6. COMPLETION STEPS
• Installlocksethardwareinaccordancewithhardwaremanufacturer’s
instructions.
• Applyinteriorandexteriorcasingormoldingasdesired.Note:Yourdoorunit
mayalreadyhaveexteriorbrickmoldapplied.
• Caulkaroundtheentireframe/brickmoldoftheexteriorwall,usingahigh
qualityexteriorgradecaulk.Caulkwherethejambsandthresholdmeet,and
ontheexterioredgeofthethreshold.Thenifneededaddabeadofcaulk
betweenthejambandthethreshold(SeegureE).
• Followthepaintmanufacturer’sinstructionsforpaintingornishingthejamb.
• Removeadhesivebackingfromdustpad(includedwiththeseinstructions).
• Placedustpadrightabovethesillwiththethickeredgeundertheweather-
stripping,makingsurethethinneredgedoesnotprotrudepastthejamb.
(SeegureE).
• Donotpaintornishthebottomdoorsweep,weather-stripping,ordustpad.
Ifthesepiecesarepaintedornishedyourdoorwillnotsealproperly.
• Makesureyouleavethedooropenlongenoughtoensureproperdryingafter
paintingornishingthejamb.Thisisimportant,wetpaintornishwillstickto
theweather-strippingthenalteritsperformance.
3. SETTING THE UNIT
• Fromoutsideyourhome,centerthedoorunitintheopeningandtiltinto
position.Assureuniformspacingaroundtheunit(SeegureC).
• Shimunitinplacebydrivingtheshimsfromtheinteriorside.Besuretoshim
behindeachhinge(SeegureD).Note:shimmingtheheaderisnotnecessary.
• Plumbandsquareoneverticaljamb,thentemporarilyfastentheunitintoplace
using3"drywallscrews(notsupplied).
4. CHECK FOR PROPER ALIGNMENT
• Plumbandsquaretheotherverticaljamb.Shimbetweenjambandrough
openingtoassureproperalignment.Alsoshimbehindeachhinge.
• Removepre-hangplugfromtheborehole.Openandclosethedoor.There
shouldbeuniformspacing(1/8")betweendoorandjambonthetwosidesand
thetopofthedoor.Makeanynecessaryadjustmentstotheunitnow,toassure
uniformspacingaroundthedoor,beforeproceeding.
• Besurethedoorsweepcontactsthethresholdevenly.Makenecessary
adjustmentsnow,beforeproceeding.
• Testtheadjustablethreshold(SeegureE).Totest,placeasheetofpaper
overthethresholdandclosethedoorthen,pullonthepaper.Ifthethreshold
adjustmentiscorrecttherewillbesometensiononthepaperasyoupullit.
Ifthepapertears,thethresholdistoohigh.Ifthereisnotensionatallonthe
paperwhenyoupullit,thethresholdistoolow.Toadjustthethreshold,tighten
orloosenallscrewsonthesill,1/2aturnatatime(lefttoloosenandright
totighten.Thenrepeatthepapertest.Rememberyouwantthepapertohave
sometensionasyoupullit,withouttearingthepaper.
PRE-HUNG SINGLE DOOR INSTALLATION INSTRUCTIONS
FIGURE A:
Caulk
Pre-hangingPlug:
Leaveinplaceuntilunit
istemporarilyfastened.
Pre-hangingPlugScrew:
Removethescrew
beforefasteningtheunit.
FIGURE B:
FIGURE E:
BottomDoorSweep
ThresholdScrews:
Adjustallsillscrews
halfturnupordown,
onlyifnecessary.
Caulkafter
installation
iscomplete.
LGP092409
Installdust
padhere.
Weather-stripping
FIGURE C:
SecurityPlate
(Donotremove)
FIGURE D:
Shimateveryarrowlocation.
(Besuretoshim
behindeachhinge)
IMPORTANT: READ THE INSTRUCTIONS COMPLETELY THROUGH BEFORE BEGINNING TO INSTALL THE DOOR UNIT.
/