LG ACC-CF-EH5C User manual

Page is loading ...

(M4 x L6) (M3 x L5.5)

2

ENG

한국어

Page is loading ...

www.lg.com

Please read this manual carefully before operating your set and retain it

for future reference.

ACC-CF-EH5C

Fixed Ceiling

Mount Kit

OWNER’S MANUAL

(M4 x L6) (M3 x L5.5)

2

ENG

ENGLISH

CAUTION

• When installing or adjusting the height of this product, two or more people are required. If you try to install or adjust

the product alone, it may fall, causing personal injury or product damage.

1 Open the product box and remove the packaging materials and the T-con box in the order they appear.

1

2

T-con box

2 Loosen the four screws and remove the cover from ceiling mount.

3

ENGENGLISH

3 Assemble the B Type pipe, cover and ceiling mount in order. Additional A Type pipes and covers are optional.

1

2

3

A Type

B Type

4 Fasten a screw (M3 x L5.5) in each screw hole between the pipes to affix them together.

4

ENG

ENGLISH

5 Fold the connectors on the opposite side of the 16/22-pin cables to make them parallel to the cable.

22

16

22

16

22

6 Insert the connectors of the 16/22-pin cables into the tubes.

16

22

16

22

7 Pass the arranged 16/22-pin cables and HDMI cables through the pipe, and reassemble the set.

FRONT

5

ENGENGLISH

8 Connect the HDMI cable with the label marked "FRONT" to the FRONT side. Insert the 16/22-pin cable with the

red mark into the cable holder and attach it using a screw (M3 x L4.5).

22

FRONT

16

RR

22

FRONT

16

RR

9 Connect the HDMI cable without the label marked "FRONT" to the REAR side. Insert the 16/22-pin cable without

the red mark into the cable holder and attach it using a screw (M3 x L4.5).

16

22

16

22

6

ENG

ENGLISH

10 Cover the FRONT side with the side of the T-con box cover that has the IR receiver and attach it using four screws

(Φ3 x L6) on the opposite side.

16

22

16

22

11

Cover the REAR side with the other T-con box cover and attach it using two screws (Φ3 x L10).

7

ENGENGLISH

Page is loading ...

FIXING THE ANCHOR SCREWS

• Check the ceiling material and the thickness of the finish material. The provided anchor screws can only be used if the

ceiling is made of concrete. Do not mount the device on ceilings made of plaster board or medium-density fiberboard

(MDF).

1 2 3

Anchor screw for

ceiling mount

4 5

Washer/

Nut

6

1

Drill a hole 45 mm to 55 mm deep using a 14.5 mm drill bit on the position you want to install your anchor.

2

Clean out the drilled hole.

3

Insert the provided anchor screw into the hole.

4

Place the ceiling mount close to the ceiling so it matches the position of the screws.

5

Fasten the washers and nuts in order. Tighten the screws using a torque of at least 45 kgf/cm.

6

Tighten the washers and nuts until they are completely fastened.

9

ENGENGLISH

Page is loading ...

16

Attach the 16/22-pin cables using two screws (M3 x L4.5).

22

16

22

16

17

Position the jack cover so the cables fit into the cut spaces and attach it using two screws (M3 x L4.5).

1

2

11

ENGENGLISH

18

Attach the mounting brackets to the Signage box using four screws (M4 x L8).

Connect the power cable to the Signage box.

1

2

12

ENG

ENGLISH

LG ACC-CF-EH5C User manual

LG ACC-CF-EH5C User manual

Related papers

Other documents