In-Sink-Erator SD150 User manual

Type
User manual
ISE
IN SINK ERATOR
MODEL SS-
150
Commercial Disposer
1-1/2 H.P. (Includes Models SS-150-1, SS-150-2, SS-150-3)
ORDER BY PART NUMBER, NOT CODE NUMBER
(Minimum Parts Order $3.00)
(All Parts F.O.B. Agency/Depot) (Include Signal and Model Number of Disposer when ordering)
EFFECTIVE May,
1976
MODEL SS-150 Commercial Disposer
1-1/2. H.P. (Includes Models SS-150-1, SS-150-2, SS-150-3)
Parts List
Code
No.
Part No.
No.
Reqd
.
Description
Code
No.
Part No.
No.
Reqd.
Description
1 11004 1 Mounting Flange 35 13075-K
1 Stator Assembly
2 11016 1 Gasket, Mounting
115/230 Volt, 60 Cycle, Single Phase
3 11024-A
1 Body, Container 36 13075-J
1 Stator Assembly
4 1491 6 Bolt, Mounting
208 Volt, 60 Cycle, Single Phase
5 11227 1 Pipe Plug 37 13076-E
1 Stator Assembly
6 11006 1 Seal, Body - Shredder
208 Volt, 60 Cycle, Three Phase
7 12443
Body and Cover Assembly 38 12433 1 Terminal Box Mounting Bracket
8 11251
Stationary Shredder
115/230 Volt, 60 Cycle, Single Phase
9 11260
Nut, Shredder
208 Volt, 60 Cycle, Single Phase
10 12445
Washer 39 12433-A
1 Terminal Box Mounting Bracket
11 12142
Washer, Fibre
208 Volt, 60 Cycle, Three Phase
12 11310
Rotor Shredder 40 12433-E
1 Terminal Box Mounting Bracket
13 12401
Upper End Bell, Includes
230/460 Volt, 60 Cycle, Three Phase
Codes 14-16-17-18 41 12384 1 Bushing
14 12321
Face Seal 42 11448 4 Screw
15 12318
Spacer Sleeve 43 11868 1 Capacitor
16 12319
Centrifugal Moisture Shield 44 12390 1 Overload Protector
17 12610
Bearing Assembly, Upper
(Use above serial #43241 only)
18 12326 1 Oil and Water Retainer
230/460 Volt, 60 Cycle, Three Phase
19 11322 2 Woodruff Key 44 12428 1 Overload Protector
20 12611
Bearing - Seal Kit Includes
(Use below serial »43241 only)
Codes 9-10-11-14-15-16-17.18-19
230/460 Volt, 60 Cycle, Three Phase
21 11444 6 Washer 45 12429 1 Overload Protector
22 11524 6 Bolt
(Use above serial S41080 only)
23 11459 1 Gasket, Outlet
208 Volt, 60 Cycle, Single Phase
24 1145B 1 Outlet Flange 45 12644 1 Overload Protector
25 1491 4 Bolt - Outlet Flange
(Use below serial ft41080 only)
26 12950 1 Rotor and Shaft Assembly
208 Volt, 60 Cycle, Single Phase
230/4AO Volt, 60 Cycle, Three Phase 45 12429 1 Overload Protector
208 Volt, 60 Cycle, Three Phase
(Use above serial #42116 only)
27 12949 1 Rotor and Shaft Assembly
115/230 Volt, 60 Cycle, Single Phase
Includes Codes 28 and 29 45 12644 1 Overload Protector
115/230 Volt, 60 Cycle, Single Phase
(Use below serial #42116 only)
208 Volt, 60 Cycle, Single Phase
115/230 Volt, 60 Cycle, Single. Phase
28 1537 2 Spring, Centrifugal Switch 46 12428 1 Overload Protector
29 12348 1 Centrifugal Switch Assembly
208 Volt, 60 Cycle, Three Phase
(Use below Serial #56471) 47 12378 1 Clamp, Overload
115/230 Volt, 60 Cycle, Single Phase 48 5765 2 Screw
29 12348 1 Centrifugal Switch Assembly 49 12372
Terminal Box
(Use below Serial M5509) 50 12383
Grommet
208 Volt, 60 Cycle; Single Phase 51 12381
Screw
29 12954 1 Centrifugal Switch Assembly 52 12415
Bearing lower
(Use above Serial #56471) 53 12399
Spring, Pre-load
115/230 Volt, 60 Cycle, Single Phase 54 12684
End Frame, lower
29 12954 1 Centrifugal Switch Assembly 55 12395
Fan
(Use above Serial B55509) 56 12635
Retaining Ring
208 Volt, 60 Cycle, Single Phase 57 12490 3 Tube, Spacer
30 7422 2 Screw 58 12382 3 Bolt, Thru
31 12393 1 Start Switch 59 12432 1 Cover, Bottom
32 1836-A
2 Screw 60 12586 2 Plug
33 12426 1 Shell - Trim 61 11757-B
2 Leg (Optional)
34 13077-E
1 Stator Assembly 62 12564 1 Ground Screw
230/460 Volt, 60 Cycle, Three Phase
ORDER BY PART NUMBER, NOT CODE NUMBER
(Minimum Parts Order $3.00)
(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
ISE
IN SINK ERATOR
IN
-
SINK
-
ERATOR
DIVISION
EMERSON ELECTRIC CO.
4700-21 ST STREET RACINE,
WISCONSIN 53406
PHONE: (414) 554-5432
Form No. C12A
-
70H
Printed in U.S.A.
COMMERCIAL DISPOSER
MODEL
CANADIAN
MODEL
SS
-
150
-
11
115/230/60/1
SS
-
150
-
17
SS
-
150
-
12
208/60/1
SS
-
150
-
18
SS
-
150
-
13
230/460/60/3
SS
-
150
-
19
SS
-
1
50
-
14
208/60/3
SS
-
1
50
-
20
ISE
IN-SINK-ERATOR
Start with Serial
#70,000
September, 1979
ORDER BY PART NUMBER, NOT CODE NUMBER
(All Parts F.O.B. Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
Code
No.
Part No.
No.
Req’d
Description
Code
No.
Part No.
No.
Req’d
Description
1 11004 1 Mounting Range 42 12433-A
1 Terminal Box Mounting Bracket
2 11016 1 Gasket, Mounting
208 Volt, 60 Hz. Three Phase
3 11024-A 1 Body Container 43 12384 1 Bushing
4 1491 6 Bolt. Mounting 44 11448 4 Screw
5 11227 1 Pipe Plug 45 11861 1 Capacitor (Single Phase only)
6 11006 1 Seal, Body-Shredder 46 12429 1 Overload Protector
7 12443 1 Body and Cover Assembly
115/230 Volt, 60 Hz. Single Phase
8 11251 1 Stationary Shredder 47 12429 1 Overload Protector
9 11260 1 Nut. Shredder
208 Volt, 60 Hz. Single Phase
10 12443 1 Washer 48 12390 1 Overload Protector
11 12142 1 Washer. Fibre
230/460 Volt, 60 Hz. Three Phase
I2 12946 1 Rotor Shredder 49 12428 1 Overload Protector
13 13082 1 End Bell, Upper. Includes Codes
201 Volt, 60 Hz. Three Phase
14 thru 21 50 12378 1 Clamp, Overload
14 12936 1 Shield 51 5765 2 Screw
15 12937 6 Screw 52 12372 1 Terminal Box
16 12934-A 1 Seal Assembly 53 12383 1 Gr ommet
17 12935 1 Sleeve, Spacer 54 12381 1 Screw
18 12860 1 O'Ring 55 1241S 1 Bearing, Lower
19 12319 1 Centrifugal Moisture Shield 56 12399 1 Spring, Pre-load
20 12610 1 Bearing Assembly, Upper 57 12684 1 End frame, Lower
21 12326 I Oil & Water Retainer 51 1239S 1 Fan
22 11322 3 Woodruff Key 59 1263S 1 Retaining Ring
23 13080 1 Bearing Seal Kit. Includes Codes 9, 10 60 12490 3 Tube Spacer
11, 14, I5, 16, 17, 18, 19, 20, 21, 22 61 12382 3 Bolt, Thru
24 11444 6 Washer 62 12432 1 Cover, Bottom
25 11524 6 Bolt 63 12964 1 Ground Screw
26 11459 1 Gasket Outlet 64 11757-8 2 Leg (Optional)
27 11458 1 Outlet Flange
28 13369 4 Bolt. Outlet Flange
CANADIAN ONLY
29 12949 1 Rotor & Shaft Assembly 65 13075-N
1 Stator Assembly
(Includes Code #30)
115/230 Volt. 60 Hz. Single Phase
208 Volt, 60 Hz. Single Phase 66 13075-M
1 Stator Assembly
115/230 Volt, 60 Hz. Single Phase
201 Volt, 60 Hz. Single Phase
30 12954 1 Centrifugal Switch Assembly 67 13077-M
1 Stator Assembly
31 12950 1 Rotor & Shaft Assembly
230/460 Volt, 60 Hz. Three Phase
208 Volt, 60 Hz. Three Phase 68 13076-H
1 Stator Assembly
230/460 Volt, 60 Hz. Three Phase
201 Volt, 60 Hz. Three Phase
32 7422 2 Screw 69 12949-A
I Rotor & Shaft Assembly
33 12393 1 Start Switch
(15/230 Volt, 60 Hz. Single Phase &
34 1836-A 2 Screw
208 Volt, 60 Hz. Single Phase
35 12426 1 Shell - Trim 70 12950-A
1 Rotor & Shaft Assembly
36 13075-K 1 Stator Assembly
230/460 Volt, 60 Hz. Three Phase &
1 15/ 230 Volt, 60 Hz. Single Phase
208 Volt, 60 Hz. Three Phase
37 13075-J 1 Stator Assembly 71 11925 1 Overload Protector
208 Volt, 60 Hz. Single Phase
115/230 Volt, 60 Hz. Single Phase &
38 13077-E 1 Stator Assembly
208 Volt, 60 Hz. Single Phase
230/460 Volt, 60 Hz, Three Phase 72 12421 1 Overload Protector
39 13076-E 1 Stator Assembly
230/460 Volt, 60 Hz. Three Phase
208 Volt, 60 Hz. Three Phase 73 12618 1 Overload Protector
40 12433 1 Terminal Box Mounting Bracket
208 Volt, 60 Hz. Three Phase
208 Volt, 60 Hz. Single Phase
41 12433-E I Terminal Box Mounting Bracket
230/460 Volt, 60 Hz. Three Phase
ORDER BY PART NUMBER HOT CODE NUMBER
(All Parts FOB Agency/Depot) (Includes Serial and Model Number of Dispenser when ordering)
MODEL
CANADIAN
MODEL
SS-150-11
115/230/60/1
SS-150-17
SS-150-12
208/60/1
SS-150-18
SS-150-13
230/460/60/3
SS-150-19
SS-150-14
208/60/3
SS-150-20
ISE
IN SINK ERATOR
IN
-
SINK
-
ERATOR DIVISION
EMERSON ELECTRIC CO
4700-21st STREET
RACINE, WISCONSIN
53406 PHONE (4l4)
Start Date:
11/05/76
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-16
(230/460Volt / 50Hz / 3 Phase)
Engineer
Number: 13027K
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1 11004 1 Flange, Mounting 29 12950 1 Rotor & Shaft Assy
2 11016 1 Gasket, Mounting 30 12426 1 Trim, Band
3 11024A 1 Body, Assy, Upper 31 1836A 2 Screw
4 1491 6 Screw, Mounting 32 13077G 1 Stator Assy
5 11227 1 Pipe, Plug 33 12433E 1 Bracket
6 11006 1 Gasket, Shredder Assy(Mounting)
7 12443 1 Body & Cover Assy 34 12384 1 Bushing
8 11251 1 Shredder, Stationary 35 11448 4 Screw
9 11260 1 Nut 36 13422AH
1 Overload, Protector
10 12445 1 Washer 37 12378 1 Clamp, Overload
11 12142 1 Washer, Fiber 38 8221 2 Screw, Tapping
12 12946 1 Shredder Assy, Rotor 39 13396 1 Box, Terminal Assy
13 13082 1 End Bell Assy, Upper
(Incl. code 40)
(Incl. Codes 9-11 &14-22 40 12383 1 Grommet, Overload
14 12936 1 Shield 41 12381 1 Screw
15 1269 6 Screw, Tapping 42 12415 1 Bearing, Lower
16 12934A 1 Seal Assy 43 12399 1 Washer, Spring
17 12935 1 Sleeve, Spacer 44 12684 1 End Frame, Lower
18 12860 1 0-Ring 45 12395 1 Fan
19 12319 1 Slinger 46 12635 1 Ring, Retaining
20 12610 1 Bearing Assy, Upper 47 12490 3 Tube, Spacer
21 12326 1 Seal, Water & Oil 48 12382A 3 Bolt, Thru
22 11322 3 Key, Woodruff 49 12432 1 Cover, Bottom
23 13080 1 Bearing Seal Kit (Incl. 50 2466 1 Screw, Ground
Codes 9-11 & 14-22) 51 11757B 2 Tube Assy, Foot
24 11444 6 Washer, Lock
(Optional)
25 11524 6 Screw
26 11459 1 Gasket, Outlet
27 11458 1 Outlet, Flange
28 13369 4 Bolt, Outlet Flange
Start Date:
1/85
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-24
U.S.A.
(115/208-230/60/1ø)
Engineer Number:
13387
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1 11004 1 Flange, Mounting 31 8221 2 Screw
2 11016 1 Gasket, Mounting 32 12393 1 Switch, Start
3 11024-A 1 Body Assy, Upper
(Single Phase Only)
4 1491 6 Screw, Mounting 33 1836-A 2 Screw
5 11227 1 Pipe Plug 34 12426 1 Trim, Band
6 11006 1 Gasket, Shredder 35 13075-K 1 Stator Assy
7 12443 1 Body & Cover Assy
(Single Phase)
8 11251 1 Shredder, Stationary 36 12433 1 Bracket Assy, Mounting
9 11260 1 Nut
(Single Phase)
10 12445 1 Washer 37 12384 1 Bushing
11 12142 1 Washer, Fiber 38 11448 4 Screw
12 12946 1 Shredder Assy, Rotor 39 11868 1 Capacitor
13 13082 1 End Bell Assy, Upper
(Single Phase Only)
(lncl Codes 9- 11 & 14-22) 40 13422-S 1 Overload, Protector
14 12936 1 Shield
(Single Phase)
15 1269 6 Screw, Tapping 41 12378 1 Clamp, Overload
16 12934-A 1 Seal Assy 42 5765 2 Screw, Tapping
17 12935 1 Sleeve, Spacer 43 12372
Box, Terminal
18 12860 1 O-Ring 44 12383
Grommet, Overload
19 12319 1 Slinger 45 12381
Screw
20 12610 1 Bearing Assy, Upper 46 12415
Bearing, Lower
21 12326 1 Seal, Water & Oil 47 12399
Washer, Spring
22 11322 3 Key, Woodruff 48 12684
End Frame, Lower
23 13080 1 Bearing Seal Kit 49 12395
Fan
(Incl Codes 9- 11 & 14- 22) 50 12635
Ring, Retaining
24 11444 6 Washer, lock 51 12490 3 Tube, Spacer
25 11524 6 Screw 52 12382-A 3 Bolt. Thru
26 11459 1 Gasket, Tailpipe 53 12432 1 Cover, Bottom
27 11458 1 Flange, Tailpipe 54 2466-A 1 Screw, Ground
28 13369 4 Screw, Tailpipe 55 11757-B 2 Tube Assy, Foot
29 12949-A 1 Rotor & Shaft Assy
(Optional)
(Single Phase)
(IncI Codes 30 & 46)
30 12954 2 Centrifugal Actuator
(Single Phase Only)
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL
SS-150-24 115/208/230/60/1
SS-150-25 08/230/460/60/3
ORDER BY PART NUMBER, HOT CODE NUMBER
(All Parts FOB Agency/Depot) (Include Serial and Model Number of Disposer when ordering)
COMMERCIAL DISPOSER
MODEL
SS-150-24 115/208/230/60/1
SS-150-25 208/230/460/60/3
Code
No.
Part
No.
No.
Req
Description
Code
No.
Part
No.
No
Req
Description
1 11004 1 Mounting Flange 31 12950A
1 Rotor & Shaft Assy. (Three Phase)
2 11016 1 Mounting Gasket
(Includes Code 50)
3 11024A 1 Body Container 32 8221 2 Screw
4 1491 6 Screw Mounting 33 12393 1 Switch Start (Single Phase only)
5 11227 1 Pipe Plug 34 1836A 2 Screw
6 11006 1 Gasket 35 12426 1 Trim Shell
7 12443 1 Body & Cover Assembly 36 13075K
1 Stator (Single Phase)
8 11251 1 Shredder Stationary 37 13077H
1 Stator (Three Phase)
9 11260
Nut 38 12433 1 Bracket Mounting - Terminal Box
10 1244S
Washer
(Single Phase)
11 12142 Washer Fiber 39 12433A
1 Bracket Mounting - Terminal Box
12 12946
Rotor Shredder
(Three Phase)
13 13082
Upper End Bell 40 12384 1 Bushing
(Includes Codes 9, 10, 11 & 14 thru 22) 41 11448 4 Screw
14 12936 1 Shield 42 11868 1 Capacitor (Single Phase only)
15 1269 6 Screw 43 12429 1 Overload Protector (Single Phase)
16 12934A
Seal Assembly 44 12428 1 Overload Protector (Three Phase)
17 12935
Sleeve Spacer 45 12378 1 Clamp Overload
18 12860
"0" Ring 46 5765 2 Screw
19 12319
Slinger 47 12372 1 Terminal Box
20 12610
Bearing Assembly Upper 48 12383 1 Grommet
21 12326 Oil & Water Seal 49 12381 1 Screw
22 11322 3 Key Woodruff 50 12415 1 Bearing Lower
23 13080 1 Bearing Seal Kit 51 12399 1 Spring Preload
(Includes Codes 9. 10, 11 & 14 thru 22) 52 12684 1 lower End Frame
24 11444 6 Washer 53 1239S 1 Fan
25 11524 6 Screw 54 1263S 1 Ring Retainer
26 11459 1 Gasket Outlet 55 12490 3 Tube Spacer
27 11458 1 Flange Outlet 56 12382A
3 Bolt Thru
28 13369 4 Screw 57 12432 1 Cover Bottom
29 12949 1 Rotor 8& Shaft Any. (Single Phase) 58 2466A 1 Screw Ground
(Includes Codes 30 & 50) 59 11757B
2 Leg Assembly (Optional)
30 12954 1 Centrifugal Switch
(Single Phase only)
ORDER BY PART NUMBER, NOT CODE NUMBER
(All Parts F.O.B. Agency/Depot) | Includes Serial and Model Number of Disposer when ordering)
ISE
IN SINK ERATOR
IN
-
SINK
-
ERATOR DIVISION
EMERSON ELECTRIC CO.
4700-21 ST STREET
RACINE, WISCONSIN
53406
PHONE: (414) 554-5432
Start Date:
4/87
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-26
CANADIAN
(115/208-230/60/1ø)
Engineer Number:
13387B
ORDER BY PART NUMBER. NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Flange, Mounting
31
8221
2
Screw
2 11016 1 Gasket, Mounting 32 12393 1 Switch, Start
3 11024-A
1 Body Assy, Upper
(Single Phase Only)
4 1491 6 Screw, Mounting 33 1836-A 2 Screw
5 11227 1 Pipe Plug 34 12426 1 Trim, Band
6 11006 1 Gasket, Shredder 35 13075-K
1 Stator Assy
7 12443 1 Body & Cover Assy
(Single Phase)
8 11251 1 Shredder, Stationary 36 12433-K
1 Bracket Assy, Mounting
9 11260 1 Nut
(Single Phase)
10 12445 1 Washer 37 12384 1 Bushing
11 12142 1 Washer, Fiber 38 11448 4 Screw
12 12946 1 Shredder Assy, Rotor 39 11868 1 Capacitor
13 13082 1 End Bell Assy, Upper
(Single Phase Only)
(Incl Codes 9-11 & 14-22) 40 13422-S
1 Overload, Protector
14 12936 1 Shield
(Single Phase)
15 1269 6 Screw, Tapping 4) 12378 1 Clamp, Overload
16 12934-A
1 Seal Assy 42 5765 2 Screw, Tapping
17 12935 1 Sleeve, Spacer 43 12372 1 Box, Terminal
18 12860 1 O-Ring 44 12383 1 Grommet, Overload
19 12319 1 Slinger 45 12381 1 Screw
20 12610 1 Bearing Assy, Upper 46 12415 1 Bearing, Lower
21 12326 1 Seal, Water & Oil 47 12399 1 Washer, Spring
22 11322 3 Key, Woodruff 48 12684 1 End Frame, Lower
23 13080 1 Bearing Seal Kit 49 12395 1 Fan
(lncl Codes 9-11&14-22) 50 12635 1 Ring, Retaining
24 11444 6 Washer, Lock 51 12490 3 Tube, Spacer
25 11524 6 Screw 52 12382-A 3 Bolt, Thru
26 11459 1 Gasket, Tailpipe 53 12432 1 Cover, Bottom
27 11458 1 Flange, Tailpipe 54 2466-A 1 Screw, Ground
28 13369 4 Screw, Tailpipe 55 11757-B
2 Tube Assy, Foot
29 12949-A
1 Rotor & Shaft Assy
(Optional)
(Single Phase)
(Incl Codes 30 & 46)
30 12954 2 Centrifugal Actuator
(Single Phase Only)
Start Date:
8/87
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-30
USA
(208-230/460/60/3ø)
Engineer Number:
13387G
ORDER BY PART NUMBER. NOT CODE NUMBER
CODE
NO.
PART NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART NO.
NO.
REQ.
DESCRIPTION
1 11004 1 Flange, Mounting 29 12950 1 Rotor & Shaft Assy
2 11016 1 Gasket, Mounting
(Three Phase)
3 11024-A 1 Body Assy, Upper
(IncI Codes 42)
4 1491 6 Screw, Mounting 30 1836-A 2 Screw
5 11227 1 Pipe Plug 31 12426 1 Trim, Band
6 11006 1 Gasket, Shredder 32 13077-E
Stator Assy
7 12443
Body & Cover Assy
(Three Phase)
8 11251
Shredder, Stationary 33 12433-A 1 Bracket (Terminal Box)
9 11260
Nut
(Three Phase)
10 12445
Washer 34 12384 1 Bushing
11 12142
Washer, Fiber 35 11448 4 Screw
12 12946
Shredder Assy, Rotor 36 13422-M 1 Overload, Protector
13 13082
End Bell Assy, Upper
(Three Phase)
(lncl Codes 9- 11 & 14-22) 37 12378 1 Clamp, Overload
14 12936
Shield 38 5765 2 Screw, Tapping
15 1269 6 Screw, Tapping 39 12372 1 Box, Terminal
16 12934-A
Seal Assy 40 12383 1 Grommet, Overload
17 12935
Sleeve, Spacer 41 12381 1 Screw
18 12860
O-Ring 42 12415
Bearing, lower
19 12319
Slinger 43 12399
Washer, Spring
20 12610
Bearing Assy, Upper 44 12684
End Frame, Lower
21 12326
Seal, Water & Oil 45 12395
Fan
22 11322 3 Key, Woodruff 46 12635
Ring, Retaining
23 13080 1 Bearing Seal Kit 47 12490 3 Tube, Spacer
(lncl Codes 9 - 11 & 14-22) 48 12382-A 3 Bolt, Thru
24 11444 6 Washer. Lock 49 12432 1 Cover, Bottom
25 11524 6 Screw 50 2466-A 1 Screw, Ground
26 11459 1 Gasket, Tailpipe 51 11757-B 2 Tube Assy, Foot
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw, Tailpipe
Start Date:
4/1/87
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-31
CANADIAN
(208-230/460/60/3ø)
Engineer Number:
13387H
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1
11004
Flange, Mounting
29
12950
1
Rotor &
Shaft Assy
2 11016
Gasket, Mounting
(Three Phase)
3 11024-A
Body Assy, Upper
(IncI Codes 42)
4 1491 6 Screw, Mounting 30 1836-A 2 Screw
5 11227
Pipe Plug 31 12426 1 Trim, Band
6 11006
Gasket, Shredder 32 13077-E
1 Stator Assy
7 12443
Body & Cover Assy
(Three Phase)
8 11251
Shredder, Stationary 33 12433-A 1I Bracket (Terminal Box)
9 11260
Nut
(Three Phase)
10 12445
Washer 34 12384 1 Bushing
11 12142 1 Washer, Fiber 35 11448 4 Screw
12 12946 1 Shredder Assy, Rotor 36 13422-M
1 Overload, Protector
13 13082 1 End Bell Assy, Upper
(Three Phase)
(Incl Codes 9- 11 & 14-22) 37 12378 1 Clamp, Overload
14 12936 1 Shield 38 5765 2 Screw, Tapping
15 1269 6 Screw, Tapping 39 12372 1 Box, Terminal
16 12934-A
Seal Assy 40 12383 1 Grommet, Overload
17 12935
Sleeve, Spacer 41 12381 1 Screw
18 12860
O-Ring 42 12415 1 Bearing, Lower
19 12319
Slinger 43 12399 1 Washer, Spring
20 12610
Bearing Assy, Upper 44 12684 1 End Frame, lower
21 12326
Seal, Water & Oil 45 12395 1 Fan
22 11322 3 Key, Woodruff 46 12635 1 Ring, Retaining
23 13080
Bearing Seal Kit 47 12490 3 Tube, Spacer
(IncI Codes 9- 11 & 14-22) 48 12382-A 3 Bolt, Thru
24 11444 6 Washer, Lock 49 12432 1 Cover, Bottom
25 11524 6 Screw 50 2466-A 1 Screw, Ground
26 11459
Gasket, Tailpipe 51 11757-B
2 Tube Assy, Foot
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw, Tailpipe
Start Date:
5/88
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-32
USA
(115/208-230/60/1ø)
Engineer Number:
13387J
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Fla
nge, Mounting
31
8221
2
Screw
2 11016 1 Gasket, Mounting 32 12393 1 Switch, Start
3 11024-C 1 Body Assy, Upper
(Single Phase Only)
4 1491 6 Screw, Mounting 33 1836-A 2 Screw
5 11227 1 Pipe Plug 34 12426 1 Trim, Band
6 11006 1 Gasket, Shredder 35 13075-K 1 Stator Assy
7 12443 1 Body & Cover Assy
(Single Phase)
8 11251 1 Shredder, Stationary 36 12433 1 Bracket Assy, Mounting
9 11260 1 Nut
(Single Phase)
10 12445 1 Washer 37 12384 1 Bushing
11 12142 1 Washer, Fiber 38 11448 4 Screw
12 12946 1 Shredder Assy, Rotor 39 11868 1 Capacitor
13 13082 1 End Bell Assy, Upper
(Single Phase Only)
(lncl Codes 9- 11 & 14-22) 40 13422-S 1 Overload, Protector
14 12936 1 Shield
(Single Phase)
15 1269 6 Screw, Tapping 41 12378 1 Clamp, Overload
16 12934-A 1 Seal Assy 42 5765 2 Screw, Tapping
17 12935 1 Sleeve, Spacer 43 12372 1 Box, Terminal
18 12860 1 O-Ring 44 12383 1 Grommet, Overload
19 12319 1 Slinger 45 12381
Screw
20 12610 1 Bearing Assy, Upper 46 12415
Bearing, Lower
21 12326 1 Seal, Water & Oil 47 12399
Washer, Spring
22 11322 3 Key. Woodruff 48 12684
End Frame, Lower
23 13080 1 Bearing Seal Kit 49 12395
Fan
(IncI Codes 9- 11 & 14-22) 50 12635
Ring, Retaining
24 11444 6 Washer, Lock 51 12490 3 Tube, Spacer
25 11524 6 Screw 52 12382-A 3 Bolt, Thru
26 11459 1 Gasket, Tailpipe 53 12432
Cover, Bottom
27 11458 1 Flange, Tailpipe 54 2466-A
Screw, Ground
28 13369 4 Screw, Tailpipe 55 11757-B 2 Tube Assy, Foot
29 12949-A 1 Rotor & Shaft Assy
(Optional)
(Single Phase)
(IncI Codes 30 & 46)
30 12954 2 Centrifugal Actuator
(Single Phase Only)
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1
11004
1
Fla
nge, Mounting
29
12950
1
Rotor & Shaft Assy
2 11016 1 Gasket, Mounting
(Three Phase)
3 11024-C
1 Body Assy, Upper
(IncI Codes 42)
4 1491 6 Screw, Mounting 30 1836-A 2 Screw
5 11227 1 Pipe Plug 31 12426 1 Trim, Band
6 11006 1 Gasket, Shredder 32 13077-E 1 Stator Assy
7 12443 1 Body & Cover Assy
(Three Phase)
8 11251 1 Shredder, Stationary 33 12433-A 1 Bracket (Terminal Box)
9 11260 1 Nut
(Three Phase)
10 12445 1 Washer 34 12384 1 Bushing
11 12142 1 Washer, Fiber 35 11448 4 Screw
12 12946 1 Shredder Assy, Rotor 36 13422-M 1 Overload, Protector
13 13082 1 End Bell Assy, Upper
(Three Phase)
(lncl Codes 9. 11 & 14-22) 37 12378 1 Clamp, Overload
14 12936 1 Shield 38 5765 2 Screw, Tapping
15 1269 6 Screw, Tapping 39 12372 1 Box, Terminal
16 12934-A
1 Seal Assy 40 12383 1 Grommet, Overload
17 12935 1 Sleeve, Spacer 41 12381 1 Screw
18 12860 1 O-Ring 42 12415 1 Bearing, Lower
19 12319 1 Slinger 43 12399 1 Washer, Spring
20 12610 1 Bearing Assy, Upper 44 12684 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 45 12395 1 Fan
22 11322 3 Key, Woodruff 46 12635 1 Ring, Retaining
23 13080 1 Bearing Seal Kit 47 12490 3 Tube, Spacer
(lncl Codes 9- 11 & 14-22) 48 12382-A 3 Bolt, Thru
24 11444 6 Washer, Lock 49 12432 1 Cover, Bottom
25 11524 6 Screw 50 2466-A 1 Screw, Ground
26 11459 1 Gasket, Tailpipe 51 11757-B 2 Tube Assy, Foot
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw, Tailpipe
Start Date:
5/88
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-33
USA
(208-230/460/60/3ø)
Engineer Number:
13387K
Start Date:
09/09/92
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-34
(115/208/230 Volt/ 60Hz/ 1 Phase)
Rev:12/93
Engineer Number:
13662
CODE NO.
PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
Flange, Mountin
g
30
13708
1
Centrifugal Actuator
2 11016
Gasket, Mounting 31 8221 2 Screw (8-32x1/2)
3 11024-A
Body, Assy, Upper 32 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 33 12426 1 Trim Band
5 11227 Plug, Pipe 34 1836-A 2 Screw (8-32x1/2)
6 11006
Gasket, Shredder 35 13713-D 1 Stator Assy
7 12443
Assy, Body & Cover 36 12433-J 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 37 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 38 11868 1 Capacitor
11 12142 1 Washer, Fiber 39 8221 2 Screw (8-32x1/2)
12 12946 1 Assy, Rotor Shredder 40 13396 1 Box, Terminal Assy
13 13723 1 Assy, Upper End Bell
(Incl. code 42)
(Incl. Codes 14-22) 41 12381 1 Screw (8-32x1-1/4)
14 12936 1 Shield 42 12383 1 Grommet, Overload
15 1269 6 Screw (8-18x1/2) 43 12378 1 Clamp, Overload
16 12934-A 1 Assy, Seal 44 13422-S 1 Overload Protector
17 12935 1 Sleeve, Spacer 45 2466-A 1 Screw, Ground
18 12860 1 O-Ring 46 12384 1 Bushing
19 12319 1 Slinger 47 13709 1 Bearing, Lower
20 12610 1 Assy, Upper Bearing 48 13678 1 Spring, Pre-load
21 12326 1 Seal, Water & Oil 49 13710 1 End Frame, Lower
22 11322 3 Key, Woodruff 50 13676 1 Fan
23 13080 1 Kit, Bearing Seal (Incl. 51 13677 1 Ring, Retaining
Codes 9 -11 & 14 -22) 52 12490 3 Tube, Spacer
24 11444 6 Washer, Lock 53 12432 1 Cover, Bottom
25 11524 6 Screw(1/4-20x1) 54 12382-A 3 Bolt Thru
26 11459 1 Gasket, Tailpipe 55 11757-B 2 Tube, Foot Assy.
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw (1/4-20x3/4
29 13675 1 Rotor & Shaft Assy.
(Incl. Codes 30 & 47)
Start Date:
02/26/93
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-35
(C.S.A.)
(115/208/230 Volt/ 60 Hz / 1 Phase)
Engineer Number:
13662-B
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
CODE
NO.
PART
NO.
NO.
REQ.
DESCRIPTION
1 11004 1 Flange, Mounting 30 13708 1 Centrifugal Actuator
2 11016 1 Gasket, Mounting 31 8221 2 Screw (8-32x1/2)
3 11024-A 1 Body, Assy, Upper 32 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 33 12426 1 Trim Band
5 11227 1 Plug, Pipe 34 1836-A 2 Screw(8-32x1/2)
6 11006 1 Gasket. Shredder 35 13713-D
1 Stator Assy
7 12443 1 Assy, Body & Cover 36 12433-J 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 37 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 38 11868 1 Capacitor
11 12142 1 Washer, Fiber 39 8221 2 Screw (8-32x1/2)
12 12946 1 Assy, Rotor Shredder 40 13396 1 Box, Terminal Assy
13 13723 1 Assy, Upper End Bell
(Incl. code 42)
(lncl. Codes 14-22) 41 12381 1 Screw (8-32x1-1/4)
14 12936 1 Shield 42 12383 1 Grommet, Overload
15 1269 6 Screw (8-18x1/2) 43 12378 1 Clamp, Overload
16 12934-A 1 Assy, Seal 44 13422-S
1 Overload Protector
17 12935 1 Sleeve, Spacer 45 12384 1 Bushing
18 12860 1 O-Ring 46 2466-A 1 Screw, Ground
19 12319 1 Slinger 47 13709 1 Bearing, Lower
20 12610 1 Assy, Upper Bearing 48 13678 1 Spring, Pre-load
21 12326 1 Seal, Water & Oil 49 13710 1 End Frame, Lower
22 11322 3 Key, Woodruff 50 13676 1 Fan
23 13080 1 Kit, Bearing Seal (Incl. 51 13677 1 Ring, Retaining
Codes 9-11 & 14-22) 52 12490 3 Tube, Spacer
24 11444 6 Washer, Lock 53 12432 1 Cover, Bottom
25 11524 6 Screw(1/4-20x1) 54 12382-A 3 Bolt, Thru
26 11459 1 Gasket, Tailpipe 55 11757-B
2 Tube, Foot Assy.
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw (1/4-20x3/4)
29 13675 1 Rotor & Shaft Assy.
(Incl. Codes 30 & 47)
Start Date:
9-1-92
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-36
(208/230/460 Volt/ 60 Hz/ 3 Phase)
Engineer Number:
13662-A
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
28
13369
4
Screw
(1/4
-
20x3/4)
2 11016 1 Gasket, Mounting 29 13675-C 1 Rotor & Shaft Assy
3 11024-A 1 Body, Assy, Upper
(Incl. Code 43)
4 1491 6 Screw (1/4-20x3/4) 30 12426 1 Trim, Band
5 11227 1 Pipe, Plug 31 1836-A 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 32 13714-0 1 Stator Assy
7 12443 1 Body & Cover Assy 33 12433-E 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 34 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 35 13422-M 1 Overload, Protector
11 12142 1 Washer, Fiber 36 12378 1 Clamp, Overload
12 12946 1 Shredder Assy, Rotor 37 8221 2 Screw (8-32x1/2)
13 13723 1 End Bell Assy, Upper 38 13396 1 Box, Terminal
(Incl. Codes 14 thru 22)
(Incl. code 40)
14 12936 1 Shield 39 12381 1 Screw (8-32x1-1/4)
15 1269 6 Screw (8-18x1/2) 40 12383 1 Grommet, Overload
16 12934-A 1 Seal Assy 41 12384 1 Bushing
17 12935 1 Sleeve, Spacer 42 2466-A 1 Screw, Ground
18 12860 1 O-Ring 43 13709 1 Bearing, Lower
19 12319 1 Slinger 44 13678 1 Spring, Pre-load
20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 46 13676 1 Fan
22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining
23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer
codes 9-10-11 & 14 thru 22) 49 12382-A 3 Bolt, Thru
24 11444 6 Washer, Lock 50 12432 1 Cover, Bottom
25 11524 6 Screw (1/4-20x1/2) 51 11757-B 2 Tube Assy, Foot
26 11459 1 Gasket, Tailpipe
(Optional)
27 11458 1 Flange, Outlet
Start Date:
02/26/93
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-37 (C.S.A.)
(208/230/460 Volt / 60 Hz / 3 Phase)
Engineer Number:
13662-C
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
28
13369
4
Screw
(1/4
-
20x3/4)
2 11016 1 Gasket, Mounting 29 13675-C 1 Rotor & Shaft Assy
3 11024-A 1 Body, Assy, Upper
(Incl. Code 43)
4 1491 6 Screw (1/4-20x3/4) 30 12426 1 Trim, Band
5 11227 1 Pipe, Plug 31 1836-A 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 32 13714-D 1 Stator Assy
7 12443 1 Body & Cover Assy 33 12433-E 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 34 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 35 13422-M 1 Overload, Protector
11 12142 1 Washer, Fiber 36 12378 1 Clamp, Overload
12 12946 1 Shredder Assy. Rotor 37 8221 2 Screw (8-32x1/2)
13 13723 1 End Bell Assy, Upper 38 13396 1 Box, Terminal
(Incl. Codes 14 thru 22)
(Incl. code 40)
14 12936 1 Shield 39 12381 1 Screw (8-32x1-1/4)
15 1269 6 Screw (8-18x1/2) 40 12383 1 Grommet, Overload
16 12934-A 1 Seal Assy 41 12384 1 Bushing
17 12935 1 Sleeve, Spacer 42 2466-A 1 Screw, Ground
18 12860 1 O-Ring 43 13709 1 Bearing, Lower
19 12319 1 Slinger 44 13678 1 Spring, Pre-load
20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 46 13676 1 Fan
22 11322 3 Key, Woodruff 47 13677 1 Ring, Retaining
23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer
codes 9-10-11& 14 thru 22) 49 12382-A 3 Bolt, Thru
24 11444 6 Washer, Lock 50 12432 1 Cover, Bottom
25 11524 6 Screw (1/4-20x1/2) 51 11757-B 2 Tube Assy, Foot
26 11459 1 Gasket, Tailpipe
(Optional)
27 11458 1 Flange, Outlet
Start Date:
09/09/92
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-38
(115/208/230 Volt / 60 Hz / 1 Phase)
Engineer
Number:
13662-D
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO.
PART NO. NO. REQ. DESCRIPTION
1 11004 1 Flange, Mounting 30 13708 1 Centrifugal Actuator
2 11016 1 Gasket, Mounting 31 8221 2 Screw (8-32x1/2)
3 11024-C 1 Body, Assy. Upper 32 13707 1 Switch, Start
4 1491 6 Screw (1/4-20x3/4) 33 12426 1 Trim Band
5 11227 1 Plug, Pipe 34 1836-A 2 Screw(8-32x1/2)
6 11006 1 Gasket, Shredder 35 13713-D 1 Stator Assy
7 12443 1 Assy, Body & Cover 36 12433-J 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 37 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 38 11868 1 Capacitor
11 12142 1 Washer, Fiber 39 8221 2 Screw (8-32x1/2)
12 12946 1 Assy, Rotor Shredder 40 13396 1 Box, Terminal Assy
13 13723 1 Assy, Upper End Bell
(Incl. code 42)
(lncl.Codes14-22) 41 12381 1 Screw (8-32x1-1/4)
14 12936 1 Shield 42 12383 1 Grommet, Overload
15 1269 6 Screw (8-18x1/2) 43 12378 1 Clamp, Overload
16 12934-A 1 Assy, Seal 44 13422-S 1 Overload Protector
17 12935 1 Sleeve, Spacer 45 12384 1 Bushing
18 12860 1 O-Ring 46 2466-A 1 Screw, Ground
19 12319 1 Slinger 47 13709 1 Bearing, Lower
20 12610 1 Assy, Upper Bearing 48 13678 1 Spring, Pre-load
21 12326 1 Seal, Water & Oil 49 13710 1 End Frame, Lower
22 11322 3 Key, Woodruff 50 13676 1 Fan
23 13080 1 Kit, Bearing Seal (Incl. 51 13677 1 Ring, Retaining
Codes 9-11 &14-22) 52 12490 3 Tube, Spacer
24 11444 6 Washer, Lock 53 12432 1 Cover, Bottom
25 11524 6 Screw(1/4-20x1) 54 12382-A 3 Bolt, Thru
26 11459 1 Gasket, Tailpipe 55 11757-B 2 Tube, Foot Assy.
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw (1/4-20x3/4
29 13675 1 Rotor & Shaft Assy.
(Incl. Codes 30 & 47)
Start Date:
09/01/92
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-39
(208/230/460Volt/ 60 Hz/ 3 Phase)
Engineer Number:
13662-E
CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
28
133
69
4
Screw
(1/4
-
20x3/4)
2 11016 1 Gasket, Mounting 29 13675-C 1 Rotor & Shaft Assy
3 11024-C 1 Body, Assy, Upper
(Incl. Code 43)
4 1491 6 Screw (1/4-20x3/4) 30 12426 1 Trim, Band
5 11227 1 Pipe, Plug 31 1836-A 2 Screw (8-32x1/2)
6 11006 1 Gasket, Shredder 32 13714-0 1 Stator Assy
7 12443 1 Body & Cover Assy 33 12433-E 1 Bracket Assy
8 11251 1 Shredder, Stationary
(Mounting)
9 11260 1 Nut 34 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 35 13422-M 1 Overload, Protector
11 12142 1 Washer, Fiber 36 12378 1 Clamp, Overload
12 12946 1 Shredder Assy, Rotor 37 8221 2 Screw (8-32x1/2)
13 13723 1 End Bell Assy, Upper 38 13396 1 Box, Terminal
(Incl. Codes 14 thru 22)
(Incl. code 40)
14 12936 1 Shield 39 12381 1 Screw (8-32x1-1/4)
15 1269 6 Screw (8-18x1/2) 40 12383 1 Grommet, Overload
16 12934-A 1 Seal Assy 41 12384 1 Bushing
17 12935 1 Sleeve, Spacer 42 2466-A 1 Screw, Ground
18 12860 1 O-Ring 43 13709 1 Bearing, Lower
19 12319 1 Slinger 44 13678 1 Spring, Pre-load
20 12610 1 Bearing Assy, Upper 45 13747 1 End Frame, Lower
21 12326 1 Seal, Water & Oil 46 13676 1 Fan
22 11322 3 Key. Woodruff 47 13677 1 Ring. Retaining
23 13080 1 Bearing Seal Kit (Incl. 48 12490 3 Tube, Spacer
codes 9-10-11 & 14 thru 22) 49 12432 1 Cover, Bottom
24 11444 6 Washer, Lock 50 12382-A 3 Bolt, Thru
25 11524 6 Screw (1/4-20x1/2) 51 11757-B 2 Tube Assy, Foot
26 11459 1 Gasket, Tailpipe
(Optional)
27 11458 1 Flange, Outlet
Start Date:
04-21-93
ISE
IN-SINK-ERATOR
COMMERCIAL DISPOSER
MODEL NO. SS150-40 (EXPORT)
(115/230 Volt / 50 Hz / 1 Phase)
Engineer Number:
13662-G
ORDER BY PART NUMBER, NOT CODE NUMBER
CODE NO. PART NO. NO. REQ. DESCRIPTION CODE NO. PART NO. NO. REQ. DESCRIPTION
1
11004
1
Flange, Mounting
30
14131
1
Centrifugal Actuator
2 11016 1 Gasket, Mounting 31 8221 2 Screw (8-32x1/2)
3 11024-A 1 Body, Assy, Upper 32 13707 1 Switch. Start
4 1491 6 Screw (1/4-20x3/4) 33 12426 1 Trim Band
5 11227
Plug, Pipe 34 1836-A 2 Screw(8-32x1/2)
6 11006
Gasket, Shredder 35 13713-H 1 Stator Assy
7 12443 Assy, Body & Cover 36 12433-J 1 Bracket Assy
8 11251
Shredder, Stationary
(Mounting)
9 11260
Nut 37 11448 4 Screw (8-18x1/4)
10 12445 1 Washer 38 11868 1 Capacitor
11 12142 1 Washer, Fiber 39 8221 2 Screw (8-32x1/2)
12 12946 1 Assy, Rotor Shredder 40 13396 1 Box, Terminal Assy
13 13723 1 Assy, Upper End Bell
(Incl, code 42)
(lncl. Codes 14-22) 41 12381 1 Screw (8-32x1-1/4)
14 12936 1 Shield 42 12363 1 Grommet, Overload
15 1269 6 Screw (6-18x1/2) 43 12378 1 Clamp, Overload
16 12934-A 1 Assy, Seal 44 13422-AE 1 Overload Protector
17 12935 1 Sleeve, Spacer 45 12384 1 Bushing
18 12860 1 O-Ring 46 2466-A 1 Screw, Ground
19 12319 1 Slinger 47 13709 1 Bearing, Lower
20 12610 1 Assy, Upper Bearing 48 13678 1 Spring, Pre-load
21 12326 1 Seal, Water & Oil 49 13710 1 End Frame, Lower
22 11322 3 Key. Woodruff 50 13676 1 Fan
23 13080 1 Kit, Bearing Seal (Incl. 51 13677 1 Ring, Retaining
Codes 9-11 &14-22) 52 12490 3 Tube, Spacer
24 11444 6 Washer, Lock 53 12382-A 3 Bolt, Thru
25 11524 6 Screw(1/4-20x1) 54 12432 1 Cover, Bottom
26 11459 1 Gasket, Tailpipe 55 11757-B 2 Tube, Foot Assy.
27 11458 1 Flange, Tailpipe
(Optional)
28 13369 4 Screw (1/4-20x3/4
29 13675-B 1 Rotor & Shaft Assy.
(Incl. Codes 30 & 47)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26

In-Sink-Erator SD150 User manual

Type
User manual

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI