Chevrolet Silverado 1500 2011 Owner's manual

Black plate (1,1)
Silverado/Sierra Hybrid - 2011
2011 Silverado/Sierra Hybrid M
In Brief . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Initial Drive Information . . . . . . . . 1-1
Hybrid Features . . . . . . . . . . . . . . . 1-2
Seats and Restraints . . . . . . . . . 3-1
Rear Seats . . . . . . . . . . . . . . . . . . . . 3-1
Airbag System . . . . . . . . . . . . . . . . . 3-1
Storage . . . . . . . . . . . . . . . . . . . . . . . 4-1
Additional Storage Features . . . 4-1
Instruments and Controls . . . . 5-1
Warning Lights, Gauges, and
Indicators . . . . . . . . . . . . . . . . . . . . 5-2
Information Displays . . . . . . . . . . 5-11
Vehicle Messages . . . . . . . . . . . . 5-11
Infotainment System . . . . . . . . . 7-1
Introduction . . . . . . . . . . . . . . . . . . . . 7-1
Climate Controls . . . . . . . . . . . . . 8-1
Climate Control Systems . . . . . . 8-1
Driving and Operating . . . . . . . . 9-1
Driving Information . . . . . . . . . . . . . 9-1
Starting and Operating . . . . . . . . . 9-2
Engine Exhaust . . . . . . . . . . . . . . . . 9-4
Automatic Transmission . . . . . . . 9-5
Brakes . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
Towing . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Vehicle Care . . . . . . . . . . . . . . . . . 10-1
Vehicle Checks . . . . . . . . . . . . . . . 10-2
Electrical System . . . . . . . . . . . . 10-13
Jump Starting . . . . . . . . . . . . . . . 10-15
Towing . . . . . . . . . . . . . . . . . . . . . . 10-19
Appearance Care . . . . . . . . . . . 10-24
Service and Maintenance . . . 11-1
Recommended Fluids,
Lubricants, and Parts . . . . . . . 11-2
Technical Data . . . . . . . . . . . . . . . 12-1
Vehicle Data . . . . . . . . . . . . . . . . . . 12-2
Index . . . . . . . . . . . . . . . . . . . . . i-1

Black plate (2,1)

Silverado/Sierra Hybrid - 2011

ii Introduction

The names, logos, emblems,

slogans, vehicle model names, and

vehicle body designs appearing in

this manual including, but not limited

to, GM, the GM logo, CHEVROLET,

GMC, the CHEVROLET and GMC

Truck Emblems, SILVERADO, Z71,

and SIERRA are trademarks and/or

service marks of General Motors

LLC, its subsidiaries, affiliates,

or licensors.

This manual describes features that

may or may not be on your specific

vehicle either because they are

options that you did not purchase or

due to changes subsequent to the

printing of this owner manual.

Please refer to the purchase

documentation relating to your

specific vehicle to confirm each of

the features found on your vehicle.

For vehicles first sold in Canada,

substitute the name “General

Motors of Canada Limited” for

Pontiac Motor Division wherever it

appears in this manual.

Keep this manual in the vehicle for

quick reference.

Your hybrid pickup is designed to be

more fuel efficient than the standard

pickup, which results in reduced

carbon dioxide emissions.

Canadian Vehicle Owners

Propriétaires Canadiens

A French language copy of this

manual can be obtained from your

dealer or from:

On peut obtenir un exemplaire de

ce guide en français auprès du

concessionnaire ou à l'adresse

suivante:

Helm, Incorporated

P.O. Box 07130

Detroit, MI 48207

1-800-551-4123

Numéro de poste 6438 de langue

française

www.helminc.com

Using this Supplement

This supplement contains

information specific to the unique

components of the vehicle. It does

not explain everything you need to

know about the vehicle. Read this

supplement along with the owner

manual to learn about the vehicle's

features and controls.

Index

A good place to look for what you

need is the Index in back of this

supplement. It is an alphabetical list

of what is in the supplement, and

the page number where you will

find it.

Litho in U.S.A.

Part No. 25965922 A First Printing

©

Black plate (1,1)

Silverado/Sierra Hybrid - 2011

In Brief 1-1

In Brief

Initial Drive Information

Transmission . . . . . . . . . . . . . . . . . . 1-1

Hybrid Features

High Voltage Safety

Information . . . . . . . . . . . . . . . . . . 1-2

Fuel Economy Gauge . . . . . . . . . 1-2

Automatic Engine Start/Stop

Feature . . . . . . . . . . . . . . . . . . . . . . 1-3

Regenerative Braking . . . . . . . . . 1-4

Battery . . . . . . . . . . . . . . . . . . . . . . . . 1-4

Service . . . . . . . . . . . . . . . . . . . . . . . 1-4

Initial Drive

Information

Transmission

Range Selection Mode

The Range Selection Mode switch

is located on the shift lever. To

enable the Range Selection feature,

move the column shift lever to the

M (Manual) position. The current

range will appear next to the M. This

is the highest attainable range with

all lower gears accessible. As an

example, when 3 (Third) gear is

selected, 1 (First) through 3 (Third)

gears are available.

Press the plus/minus buttons,

located on the steering column shift

lever, to select the desired range of

gears for current driving conditions.

See Automatic Transmission

Operation in the owner manual.

Cruise control can be used while the

vehicle is in Range Selection Mode.

See Manual Mode on page 9‑7.

Black plate (2,1)

Silverado/Sierra Hybrid - 2011

1-2 In Brief

Hybrid Features

High Voltage Safety

Information

This vehicle has a standard

12-volt battery and a high voltage

hybrid battery. Only a trained

service technician with the proper

knowledge and tools should inspect,

test, or replace the hybrid battery.

See your dealer if the hybrid battery

needs service.

The 12-volt battery cables, in the

engine compartment, are clearly

labeled. In emergency situations,

first responders can cut those

cables to disable the high voltage

hybrid battery system.

Fuel Economy Gauge

United States

Canada

This gauge indicates fuel efficiency.

To obtain the best fuel efficiency,

operate the vehicle so that the

indicator is in the high

efficiency band.

Modifying both braking and

acceleration behavior to keep the

indicator in the center of the gauge

will result in the best system

efficiency and fuel economy.

See Fuel Economy Gauge on

page 5‑4.

Black plate (3,1)

Silverado/Sierra Hybrid - 2011

In Brief 1-3

Automatic Engine Start/

Stop Feature

Start the engine as you would any

other engine. See “Starting the

Engine” in the owner manual for

more information on starting. The

hybrid system provides very quiet

engine starting. If pulling a trailer

with trailer brakes, see Trailer

Towing on page 9‑9 for more

information.

Auto Stop

The vehicle has an Auto Stop

feature. After a successful engine

start, the engine may turn off and

operate in the Auto Stop mode.

Keep your foot firmly on the brake

pedal until you are ready for the

vehicle to move.

Engine OFF and AUTO STOP

modes are indicated on the

tachometer display. When the

tachometer needle indicates OFF,

the engine is not running and will

remain off until the ignition key is

placed in the START position or a

remote vehicle start is performed.

When the tachometer needle

indicates AUTO STOP, the hybrid

system is on, the engine is not

running, but may Auto Start at any

time without notice. See Tachometer

on page 5‑3 for more information.

A chime will sound if the driver door

is opened while in Auto Stop as a

reminder that the ignition switch is

not in the LOCK/OFF position.

Always turn the ignition switch to

LOCK/OFF and remove the key

from the ignition switch when exiting

the vehicle.

Auto Start

The vehicle also has an Auto Start

feature. The engine will remain off

while in Auto Stop mode until

vehicle conditions require the

engine to run. The near-instant

starting of the engine from Auto

Stop mode is called Auto Start.

EV Mode

The vehicle also has an EV mode

which uses only the electric motor

to move the vehicle. With light

acceleration, the vehicle will drive in

EV mode. EV mode is unavailable

when the vehicle is out of fuel.

For more information on Auto Stop,

Auto Start, and EV Mode, see

Starting the Vehicle on page 9‑2.

Black plate (4,1)

Silverado/Sierra Hybrid - 2011

1-4 In Brief

Regenerative Braking

Regenerative braking enables the

electric drive motor to operate as a

generator when coasting or braking.

Energy from the moving vehicle

recharges the hybrid battery.

The hydraulic disc brakes work with

the regenerative braking to insure

effective braking.

The braking system is computer

controlled and blends the

regenerative braking with the

conventional hydraulic disc brakes

to meet any requirements for

deceleration. Because the controller

applies the hydraulic brakes through

its high pressure accumulator, you

may occasionally hear the motor

driven pump when it recharges the

system. This is normal. In the event

of a controller problem, the brake

pedal may be harder to push and

the stopping distance may be

longer.

See Regenerative Braking on

page 9‑8.

Battery

This vehicle has a standard

12-volt battery and a high voltage

hybrid battery. When a new

standard 12-volt battery is needed,

see your dealer for one that has the

replacement number shown on the

original battery's label. Only a

trained service technician with the

proper knowledge and tools should

inspect, test, or replace the hybrid

battery. See your dealer if the hybrid

battery needs service. See Battery

on page 10‑12.

Service

Never try to do your own service on

hybrid components. You can be

injured and the vehicle can be

damaged if you try to do your own

service work. Service and repair of

these hybrid components should

only be performed by a trained

service technician with the proper

knowledge and tools. See Doing

Your Own Service Work on

page 10‑2.

Black plate (1,1)

Silverado/Sierra Hybrid - 2011

Seats and Restraints 3-1

Seats and

Restraints

Rear Seats

Rear Seats . . . . . . . . . . . . . . . . . . . . 3-1

Airbag System

Replacing Airbag System Parts

After a Crash . . . . . . . . . . . . . . . . 3-1

Rear Seats

Folding Rear Seat

Notice: Folding a rear seat with

the safety belts still fastened may

cause damage to the seat or the

safety belts. Always unbuckle the

safety belts and return them to

their normal stowed position

before folding a rear seat.

Make sure that nothing is on

the seat.

To fold the seat, slowly pull the seat

cushion up.

To return the seat to the normal

seating position, slowly pull the seat

cushion down.

Make sure the safety belts are not

twisted or caught in the seat

cushion.

Airbag System

Replacing Airbag System

Parts After a Crash

If an airbag inflates or the vehicle

has been in a crash, the vehicle's

sensing system may command the

automatic hybrid battery disconnect

to open. When the battery

disconnect is open, the hybrid

battery will be off and the vehicle

will not start. The airbag readiness

light and/or SERVICE HYBRID

SYSTEM warning message may

come on in the Driver Information

Center (DIC). See “Airbag

Readiness Light” in the owner

manual and Driver Information

Center (DIC) on page 5‑11 for more

information.

To operate the vehicle, the

automatic hybrid battery disconnect

must be reconnected by a qualified

service technician and sensing

system parts will need to be

replaced. Have the vehicle serviced

right away.

Black plate (2,1)

Silverado/Sierra Hybrid - 2011

3-2 Seats and Restraints

2 NOTES

Black plate (1,1)

Silverado/Sierra Hybrid - 2011

Storage 4-1

Storage

Additional Storage Features

Tonneau Cover (Hard

Tonneau) . . . . . . . . . . . . . . . . . . . . 4-1

Tonneau Cover (Soft

Tonneau) . . . . . . . . . . . . . . . . . . . . 4-6

Additional Storage

Features

Tonneau Cover (Hard

Tonneau)

Installing the Cover

{

CAUTION

An improperly stored cargo cover

could be thrown about the vehicle

during a collision or sudden

maneuver. Someone could be

injured. If the cover is removed,

always store it in the proper

storage location. After positioning

the cargo cover back on the

vehicle, always be sure that it is

securely reattached by properly

securing the straps and latches.

1. Position the tonneau cover onto

the top of the pickup box with

the locator tabs positioned into

the front stake pockets.

If equipped, remove the front

stake pocket covers from the

bed rail protectors. The locators

must fully seat into the stake

pocket.

2. Align the front edge of the cover

with the front edge of the bed rail

so that it is centered on each

side of the truck bed.

3. Lower the front clamp from its

storage position.

Black plate (2,1)

Silverado/Sierra Hybrid - 2011

4-2 Storage

4. Tilt the clamp assembly so that

the locator is in the slot, pull

down on the assembly, and slide

the clamp under the edge of the

inner lip of the bed rail.

5. Pull the handle toward the rear

of the truck to engage the clamp.

Make sure the locator is secure

into the slot (A). If unable to

completely engage clamp, see

the tightening and loosening

procedures later in this section.

6. The clamp should be securely

engaged. Shake the handle

assembly to make sure the

handle does not move.

7. There are locking features on

the front clamps only. With the

handle in the clamped position,

push the locking tab to engage

the lock.

8. Repeat the clamp attachment

steps 3 through 7 for the

opposite side.

Black plate (3,1)

Silverado/Sierra Hybrid - 2011

Storage 4-3

Closing the Cover

1. Release both the retention

straps located on the top of the

cover behind the cab and press

into the stored position.

2. Unfold the tonneau cover to the

closed position.

3. Lower the rear set of clamp

assemblies from the stored

position.

4. Tilt the clamp assembly so that

the locator is in the slot, pull

down on the assembly, and slide

the clamp under the edge of the

inner lip on the bed rail.

5. Pull the handle toward the rear

of the truck to engage the clamp.

Make sure the locator is secured

into the slot (A). If unable to

completely engage clamp, see

the tightening and loosening

procedures later in this section.

6. The clamp should be securely

engaged. Shake the handle

assembly to make sure the

handle does not move.

7. Repeat the clamp attachment

steps 3 through 6 for the

opposite side.

8. Close the endgate.

Black plate (4,1)

Silverado/Sierra Hybrid - 2011

4-4 Storage

Opening the Tonneau Cover

1. Turn both of the rear handles

inward to release compression.

2. Pull the clamp down and turn the

assemblies to disengage them

from the lip of the pickup box.

3. Open the cover to expose the

handles.

4. Align the clamp assembly

bolt (A) with the retention

feature (B).

5. Turn the handle assembly and

clamp assembly bolt

sideways (A) into the slot of the

retention feature (B).

6. The handle should lie flat on the

panel with the handles facing

inward. Press firmly to secure.

This step must be done before

stowing the cover.

7. Fold the cover forward.

8. Remove the retaining strap from

the bow. Connect the retention

buckle ends. One end is located

on the front of the tonneau cover

behind the cab and the other

end is on the tonneau cover

9. Pull on each strap to make sure

both buckles are attached.

Black plate (5,1)

Silverado/Sierra Hybrid - 2011

Storage 4-5

Removing the Tonneau Cover

1. Open the cover by following the

procedure described previously,

under “Opening the Tonneau

Cover”.

2. Disengage the locking tabs,

located on the front handles, by

pulling them rearward.

3. Turn the handles inward to

release.

4. Pull the clamp down and turn the

assembly to disengage it from

the lip of the truck box.

5. Turn the cover to expose the

handles.

6. Align the clamp assembly

bolt (A), with the retention

feature (B).

7. Turn the handle assembly

sideways by tilting the assembly

bolt (A) into the slot of the

retention feature (B).

8. The handle should lie flat on the

panel with the handles facing

inward. Press firmly to secure.

9. Remove the tonneau cover from

the vehicle.

Black plate (6,1)

Silverado/Sierra Hybrid - 2011

4-6 Storage

Tightening the Clamp

1. Push the handle forward to

release it from the clamped

position.

2. Disengage the clamp from the

inner edge of the bed rail and

slide the assembly inward.

3. Adjust the clamp height on the

bolt by turning the entire clamp

assembly counter-clockwise.

4. Attach the clamps as indicated

in steps 4 and 5 of Installing the

Cover.

Loosening the Clamp

1. Return the handle to the fully

disengaged position.

2. Disengage the clamp from the

inner edge of the bed rail and

slide the assembly inward.

3. Adjust the clamp height by

turning the entire clamp

assembly clockwise.

4. Reattach the clamps as

indicated in steps 4 and 5 of

Installing the Cover.

Tonneau Cover (Soft

Tonneau)

Side Rail

{

WARNING

An improperly stored cargo cover

could be thrown about the vehicle

during a collision or sudden

maneuver. Someone could be

injured. If the cover is removed,

always store it in the proper

storage location. After positioning

the cargo cover back on the

vehicle, always be sure that it is

securely reattached by properly

securing the straps and latches.

Installation

1. The adjuster screw end of each

side rail should point in the

direction of the cab.

2. Place each side rail on top of the

truck box.

Black plate (7,1)

Silverado/Sierra Hybrid - 2011

Storage 4-7

3. Align the front edge of the side

rail with the front inside edge of

pickup box.

Clamp

Installation

1. Position three outer clamps (A),

on each side rail. The positions

on the siderails are marked

CLAMP.

2. Position the grooves of the

clamps on the side rails (A)

using the center groove (B).

Black plate (8,1)

Silverado/Sierra Hybrid - 2011

4-8 Storage

3. If the pickup box has molded

bed rail protectors (A), remove

the insert (C) from the outer

groove on the clamp, and

position the clamp on the side

rail (B) using the outer

groove (D).

4. Slide the inner clamp (B) into the

outer clamp (A).

5. Turn the latch (C) onto the outer

clamp.

6. Tighten the clamp by turning the

latch (C) toward the side rail.

Make sure there is no gap

between the rubber clamp pad

and the side rail.

7. If the truck box has a molded

bed rail protector, insert the latch

into the top notch on the inner

clamp.

8. Clean the vehicle's painted

surface below the pull strap

using a 50/50 mixture of rubbing

alcohol and tap water.

Black plate (9,1)

Silverado/Sierra Hybrid - 2011

Storage 4-9

9. Remove the paper from the

provided clear tape strip and

apply to the painted surface

below the pull strap.

Adjustment

If there is excessive sideways

movement of the crossrails, move

and re-install the clamps on the

loose areas using the inner groove

of the clamp.

Cover

Installation

1. Place the cover assembly into

the front pivot mounts firmly

against the adjustment screws.

2. Verify the gap between the

adjuster screws and pivot

mounts is 3/16 inch. Adjust if

needed.

Black plate (10,1)

Silverado/Sierra Hybrid - 2011

4-10 Storage

3. Loosen the wing bolt (A), then

slide the latch outboard into the

side rail. Tighten down the wing

bolt (A). Do this on both sides.

Both latches must remain

engaged and the wing bolts

tightened while the cover is on

the vehicle. Make sure by lifting

up on each end of the cover

assembly.

4. Unbuckle both straps and roll

the cover out. Make sure that

each bow falls in between the

side rails. If the bows do not fit

between the side rails, verify that

the clamps are pushed fully

outboard without any gaps

between the clamp pad and

pickup box. If additional

clearance is required, remove

the clamp closest to the

interference. Remove the orange

strip to allow access to the outer

slot of the upper clamp. Reinstall

the clamp using the outer groove

of the upper clamp. If bows are

too loose, adjust the clamp

closest to the bow with the

excessive clearance to the inner

groove of the upper clamp.

Black plate (11,1)

Silverado/Sierra Hybrid - 2011

Storage 4-11

5. When the cover is rolled out,

place the rear rail into the rear

pivot mounts. Firmly press down

on each side of the cover, until

the latches are secured into the

side rails. If latch is too tight,

loosen the tension adjustment

screws. If the latch is not

securely holding the rear rail,

tighten the tension adjustment

screws. Only the driver's side

has a latch.

6. Secure the driver side Velcro

®

of

the cover to the side rail. Then

pull the cover tight across the

bed and fasten the Velcro

®

on

the passenger side.

7. Secure the buckles by folding

them once, then slide them

under the cord located on the

cover.

Secure in Open Position

1. To open the cover, open tailgate

and push down on the cover.

The pull back on pull strap.

2. From the drivers side, roll the

cover up tightly.

3. When the cover is rolled up,

buckle both tie-down straps. Pull

both straps tight.

Black plate (12,1)

Silverado/Sierra Hybrid - 2011

4-12 Storage

Removal

1. Secure the cover (A) into the

open position.

2. Loosen wing bolts (B) on both

driver and passenger side of

front rail, then slide latches

inboard until released from the

side rail.

3. Pick the cover assembly up on

the driver side and pull the

whole assembly off the

truck box.

Adjustment

1. If the cover is too loose, turn the

tensioning screw clockwise to

tighten the tension of the vinyl.

This makes it harder to operate

the rear release latch. The

tensioning screws are located on

each side rail. Use the provided

1/4 inch key to turn the

tensioning screws.

2. Adjust the screws on both sides

to the same tension.

Page is loading ...

Chevrolet Silverado 1500 2011 Owner's manual

This manual is also suitable for

Chevrolet Silverado 1500 2011 Owner's manual

Related papers

Other documents