CUMMINS QD 10000 HDKCA Installation guide

English

Original Instructions 5-2017 A043D717 (Issue 6)

InstallationInstallation ManualManual

Onan Generator Set for RV

HDKCA (Spec F-H)

HDKCB (Spec F-H)

Table of Contents

1. IMPORTANT SAFETY INSTRUCTIONS ....................................................................................... 1

1.1 Overview ................................................................................................................................. 1

1.2 Warning, Caution, and Note Styles Used in This Manual ..................................................... 1

1.3 General Safety Precautions.................................................................................................... 1

1.4 Automatic Generator Start Control Hazards ........................................................................... 3

1.5 Electrical Shock and Arc Flash Can Cause Severe Personal Injury or Death ....................... 3

1.6 Generator Voltage Is Deadly .................................................................................................. 4

1.7 Engine Exhaust/Carbon Monoxide Is Deadly ......................................................................... 4

1.8 Diesel Fuel Is Combustible ..................................................................................................... 5

1.9 Battery Gas Is Explosive......................................................................................................... 5

1.10 Moving Parts Can Cause Severe Personal Injury or Death ................................................. 6

1.11 CARB .................................................................................................................................... 6

1.12 Generator Set Warning Labels ............................................................................................. 6

2. INTRODUCTION............................................................................................................................ 9

2.1 About This Manual.................................................................................................................. 9

2.2 Related Literature ................................................................................................................... 9

2.3 Installation Codes and Standards for Safety ........................................................................ 10

2.4 Electromagnetic Compatibility Compliance........................................................................... 11

2.5 Specifications........................................................................................................................ 11

2.5.1 Diesel Model Specifications ....................................................................................... 11

2.6 List of Acronyms ................................................................................................................... 12

3. LOCATION, MOUNTING, AND VENTILATION ........................................................................... 15

3.1 Location ................................................................................................................................ 15

3.1.1 Typical Generator Set Locations - Class A RV.......................................................... 16

3.1.2 Typical Generator Set Locations - Class C RV ......................................................... 16

3.2 Mounting ............................................................................................................................... 16

3.2.1 Insulating Materials .................................................................................................... 17

3.2.2 Fire and Exhaust Barriers .......................................................................................... 17

3.3 Ventilation ............................................................................................................................. 17

3.3.1 Air Recirculation ......................................................................................................... 18

4. EXHAUST CONNECTIONS......................................................................................................... 19

4.1 Tailpipe Installation ............................................................................................................... 19

4.2 Vehicle Clearances - Class A RV ......................................................................................... 22

5. FUEL CONNECTIONS................................................................................................................. 23

5.1 Bio-diesel Fuels B5 – B20 .................................................................................................... 24

6. ELECTRICAL CONNECTIONS.................................................................................................... 27

6.1 AC Power Output Connections............................................................................................. 27

6.1.1 Wiring Methods .......................................................................................................... 28

Table of Contents 5-2017

6.1.2 Connecting to Shore Power ....................................................................................... 28

6.2 Remote Control Connections................................................................................................ 29

6.3 Starting Battery Connections ................................................................................................ 31

6.3.1 Battery Compartment................................................................................................. 31

6.3.2 Battery Cable Sizes ................................................................................................... 32

6.3.3 Battery Cables............................................................................................................ 32

6.3.4 Battery Cable Connections at the Generator Set ...................................................... 34

6.3.5 Generator Set (Equipment) Grounding ...................................................................... 34

7. INSTALLATION REVIEW AND STARTUP .................................................................................. 35

7.1 Installation Review ................................................................................................................ 35

7.2 Startup .................................................................................................................................. 35

7.3 Hot Air Recirculation Test ..................................................................................................... 36

7.3.1 Test Method ............................................................................................................... 36

7.3.2 Test Requirement....................................................................................................... 37

APPENDIX A. OUTLINE DRAWINGS .............................................................................................. 39

A.0 Outline Drawing 0500-4040.................................................................................................. 41

APPENDIX B. WIRING DIAGRAMS ................................................................................................. 43

B.0 Wiring Diagrams ................................................................................................................... 44

1 Important Safety Instructions

1.1 Overview

Thoroughly read the Operator Manual before operating the generator set. It contains important instructions

that should be followed during operation and maintenance. Safe operation and top performance can only

be achieved when equipment is properly operated and maintained. The owners and operators of the

generator set are solely responsible for its safe operation.

Generator set operation, maintenance, and installation must comply with all applicable local, state, and

federal codes and regulations. Electricity, fuel, exhaust, moving parts, and batteries present hazards which

can result in severe personal injury or death. Only trained and experienced personnel with knowledge of

fuels, electricity, and machinery hazards should perform generator set installation or adjustment

procedures; or remove, dismantle, or dispose of the generator set.

1.2 Warning, Caution, and Note Styles Used in This

Manual

The following safety styles and symbols found throughout this manual indicate potentially hazardous

conditions to the operator, service personnel, or equipment.

DANGER

Indicates a hazardous situation that, if not avoided, will result in death or serious injury.

WARNING

Indicates a hazardous situation that, if not avoided, could result in death or serious injury.

CAUTION

Indicates a hazardous situation that, if not avoided, could result in minor or moderate injury.

NOTICE

Indicates information considered important, but not hazard-related (e.g., messages relating to

property damage).

1.3 General Safety Precautions

WARNING

Operation of equipment is unsafe when mentally or physically fatigued. Do not operate

equipment in this condition, or after consuming any alcohol or drug.

1. Important Safety Instructions 5-2017

WARNING

Maintaining or installing a generator set can cause severe personal injury. Wear personal

protective equipment such as safety glasses, protective gloves, hard hats, steel-toed boots, and

protective clothing when working on equipment.

WARNING

Running the generator set without the cover or service door can cause severe personal injury or

equipment damage. Do not operate the generator set with the cover or service doors removed.

WARNING

Coolants under pressure can cause severe scalding. Do not open a radiator or heat exchanger

pressure cap while the engine is running. Let the engine cool down before removing the coolant

pressure cap. Turn the cap slowly and do not open it fully until the pressure has been relieved.

WARNING

Hot metal parts can cause severe burns, Avoid contact with the radiator, turbo charger, and

exhaust system.

WARNING

Starting fluids, such as ether, can cause explosion and generator set engine damage. Do not use.

WARNING

Ethylene glycol, used as engine coolant, is toxic to humans and animals. Clean up coolant spills

and dispose of used antifreeze in accordance with local environmental regulations.

WARNING

Used engine oils have been identified by some state and federal agencies to cause cancer or

reproductive toxicity. Do not ingest, breathe the fumes, or contact used oil when checking or

changing engine oil.

CAUTION

To prevent accidental or remote starting while working on the generator set, disconnect the

negative (-) battery cable at the battery using an insulated wrench.

CAUTION

Unsecured or loose fasteners can cause equipment damage. Make sure all fasteners are secure

and properly torqued.

CAUTION

Oily rags and other material can cause fire and restrict cooling. Keep the generator set, drip pan,

and compartment clean.

1. Important Safety Instructions5-2017

CAUTION

Accumulated grease and oil can cause overheating and engine damage presenting a potential

fire hazard. Keep the generator set clean and repair any oil leaks promptly.

NOTICE

Keep multi-class ABC fire extinguishers handy. Class A fires involve ordinary combustible

materials such as wood and cloth. Class B fires involve combustible and flammable liquid fuels

and gaseous fuels. Class C fires involve live electrical equipment. (Refer to NFPA No. 10 in

applicable region.)

1.4 Automatic Generator Start Control Hazards

WARNING

Accidental starting can cause severe personal injury or death. Turn off the AGS whenever

performing maintenance or service, when the vehicle is stored between uses, is awaiting service,

or is parked in a garage or other confined area.

Unexpected starting may occur if the generator set is equipped with an inverter-charger or other Automatic

Generator Start (AGS) control. This may cause exposure to:

• Unexpected generator starting

• Moving parts hazards

• Electric shock

• Exhaust carbon monoxide (CO)

1.5 Electrical Shock and Arc Flash Can Cause Severe

Personal Injury or Death

WARNING

Electrical shocks and arc flashes can cause severe personal injury or death. Adhere to the

following guidelines:

• Only qualified service personnel certified and authorized to work on power circuits should

work on exposed energized power circuits.

• All relevant service material must be available for any electrical work performed by certified

service personnel.

• Exposure to energized power circuits with potentials of 50 VAC or 75 VDC or higher poses a

significant risk of electrical shock and electrical arc flash.

• Refer to standard NFPA 70E, or equivalent safety standards in corresponding regions, for

details of the dangers involved and for safety requirements.

1. Important Safety Instructions 5-2017

1.6 Generator Voltage Is Deadly

WARNING

Improperly connected generator electrical output connections can cause equipment damage,

severe personal injury, or death. Electrical connections must be made by a trained and

experienced electrician in accordance with applicable codes.

WARNING

Improper installations can cause equipment damage, severe personal injury, or death. All

installations must be conducted by trained and experienced personnel in accordance with the

installation instructions and all applicable codes.

WARNING

Back feed to shore power can cause electrocution and damage to equipment. The generator set

must not be connected to shore power or to any other source of electrical power. An approved

switching device must be used to prevent interconnections.

WARNING

Live electrical equipment can cause electrocution. Use caution when working on live electrical

equipment. Remove jewelry, make sure clothing and shoes are dry, stand on a dry wooden

platform or rubber insulating mat, and use tools with insulated handles.

1.7 Engine Exhaust/Carbon Monoxide Is Deadly

WARNING

Substances in exhaust gases have been identified by some state and federal agencies to cause

cancer or reproductive toxicity. Do not breathe in or come into contact with exhaust gases.

WARNING

Carbon monoxide is a poisonous gas. Inhalation of this gas can cause severe personal injury or

death. Adhere to the following bullet points to make sure carbon monoxide is not being inhaled

by occupants of the vehicle as well as others working on or around the generator set.

• Inspect for exhaust leaks, and test and confirm that all carbon monoxide detectors are

working in accordance with the manufacturer's instructions or owner's manual, prior to

every startup, and after every 8 hours of running.

• Never occupy the vehicle while the generator set is running unless the vehicle is equipped

with a working carbon monoxide detector.

• Never operate the generator set when the vehicle is in a confined space, such as a garage,

basement, or building of any kind.

• Make sure the exhaust system is installed in accordance with the generator set installation

manual.

• Never use engine cooling air for heating a working or living space compartment.

Carbon Monoxide (CO) is odorless, colorless, tasteless, and non-irritating. It cannot be seen or smelled.

Exposure, even to low levels of CO for a prolonged period can lead to asphyxiation (lack of oxygen).

1. Important Safety Instructions5-2017

Mild effects of CO poisoning include:

• headache

• dizziness

• drowsiness

• fatigue

• chest pain

• confusion

More extreme symptoms include:

• vomiting

• seizure

• loss of consciousness

1.8 Diesel Fuel Is Combustible

WARNING

Diesel fuel is highly combustible. Adhere to the following bullets to avoid igniting fuel and fuel

vapors.

• Do not smoke or turn electrical switches on or off where fuel fumes are present or in areas

sharing ventilation with fuel tanks or equipment.

• Keep flame, sparks, pilot lights, arc-producing equipment and all other sources of ignition

well away from fuel lines and sources.

• Fuel lines must be secured, free of leaks, and separated or shielded from electrical wiring.

WARNING

Flammable vapor can cause a diesel engine to over speed and become difficult to stop, resulting

in possible fire or explosion, and severe personnel injury or death. Do not operate a diesel-

powered generator set where a flammable vapor environment can be created by fuel spill, leak,

etc.

1.9 Battery Gas Is Explosive

WARNING

Battery gas is highly explosive and may cause personal injury or death if ignited. Take the proper

precautions to avoid personal injury.

• For personal safety, wear appropriate PPE when working on or around the generator set.

• To make sure battery gas is not ignited, do not smoke around the generator set.

• To reduce arcing when disconnecting or reconnecting battery cables, always disconnect

the negative (–) battery cable first and reconnect it last.

1. Important Safety Instructions 5-2017

1.10 Moving Parts Can Cause Severe Personal Injury or

Death

WARNING

Moving parts can cause severe personal injury or death, and hot exhaust parts can cause severe

burns. Make sure all protective guards are properly in place before starting the generator set.

WARNING

Hot moving, and electrically live parts can cause severe personal injury or death. Keep children

away from the generator set.

WARNING

Hot, moving, and electrically live parts can cause severe personal injury or death. Only trained

and experienced personnel should make adjustments while the generator set is running.

WARNING

Moving parts can catch on loose items such as clothing or jewelry. Do not wear loose clothing or

jewelry near moving parts such as PTO (power take-off) shafts, fans, belts, and pulleys.

WARNING

Moving parts can entangle appendages such as fingers. Keep the protective guards in place over

fans, belts, pulleys, and other moving parts and keep hands away from all moving parts.

1.11 CARB

CAUTION

Unauthorized modifications or replacement of fuel, exhaust, air intake, or speed control system

components that affect engine emissions are prohibited by law in the state of California.

The California Air Resources Board (CARB) has requirements regarding modification & repair of fuel

system & exhaust components including, but not limited to, adherence to evaporative emissions

requirements in mobile installations. Evaporative generator sets must be used in trailers, fifth wheel

trailers, and other non-motorized vehicles where on-board gasoline fuel storage is self-contained in the

trailer equipment. Completing the installation of the generator set fuel evaporative system provides

compliance with the California code of regulations for small off-road equipment effective January 1, 2008

and Federal Small SI regulation effective January 1, 2011. Any questions regarding the installation or

evaporative emission certification should be directed to Cummins Inc. for clarification.

1.12 Generator Set Warning Labels

Warning signs are provided on the generator set at or near the point of risk. To avoid injury, always take

the necessary precautions as indicated on the sample signs shown below.

1. Important Safety Instructions5-2017

Caution or Warning.

Indicates a risk of personal injury.

Caution or Warning of Temperature Hazard.

Indicates a risk of personal injury from high temperature.

Caution or Warning of High Voltage Hazard.

Indicates a risk of personal injury from electric

shock or electrocution.

Caution or Warning of Engine Coolant Pressure Hazard.

Indicates a risk of personal injury from hot pressurized engine coolant.

Caution or Warning.

Indicates to read Operator Manual for additional information.

Caution or Warning of No Step.

Indicates a risk of personal injury or equipment damage from stepping on

equipment.

Caution or Warning of Combustion or Explosion Hazard.

Indicates a risk of personal injury from explosion.

Caution or Warning of Belt and Rotating Part Hazard.

Indicates a risk of personal injury from entanglement in moving parts.

Caution or Warning of Chemical (ingestion or burn) Hazard.

Indicates a risk of personal injury or asphyxiation from poisonous fumes

or toxic gases.

Caution or Warning of High Voltage or Current Source Hazard.

Indicates a risk of personal injury from electrical shock or electrocution.

Caution or Warning of Fan and Rotating Part Hazard.

Indicates a risk of personal injury from entanglement in moving parts.

This page is intentionally blank.

1. Important Safety Instructions 5-2017

2 Introduction

2.1 About This Manual

This manual is a guide for the installation of the generator sets listed on the front cover. Proper installation

is essential for top performance. Read through this manual before starting the installation. Leave this

manual in the vehicle.

The installer must be qualified to perform installation of electrical and mechanical equipment.

This manual addresses the following aspects of the installation:

• Location, Mounting, and Ventilation

• Exhaust Connections

• Fuel Connections

• Electrical Connections

• Startup

See the Operator Manual for operation and maintenance and the Service Manual for service.

The information contained within the manual is based on information available at the time of printing. In

line with Cummins Inc. policy of continuous development and improvement, information may change at

any time without notice. The users should therefore make sure that before commencing any work, they

have the latest information available. The latest version of this manual is available on QuickServe Online

(https://quickserve.cummins.com).

2.2 Related Literature

Before any attempt is made to operate the generator set, the operator should take time to read all of the

manuals supplied with the generator set, and to familiarize themselves with the warnings and operating

procedures.

CAUTION

A generator set must be operated and maintained properly if you are to expect safe and reliable

operation. The Operator manual includes a maintenance schedule and a troubleshooting guide.

The Health and Safety manual must be read in conjunction with this manual for the safe

operation of the generator set:

• Health and Safety Manual (0908-0110)

The relevant manuals appropriate to your generator set are also available, the documents below are in

English:

• Operator Manual for RV Generator Set HDKCA and HDKCB (Spec F-H) (A043D713)

• Installation Manual for RV Generator Set HDKCA and HDKCB (Spec F-H) (A043D717)

• Parts Manual for RV Generator Set HDKCA and HDKCB (Spec F-H) (A043T420)

• Standard Repair Times - BJ Family (900-0621)

• Warranty Manual (1117-0005)

• Global Commercial Warranty Statement (A028U870)

2. Introduction 5-2017

2.3 Installation Codes and Standards for Safety

CAUTION

The Commercial Generator Set Warranty applies only when the generator set is installed in a

commercial or recreational vehicle. The RV Generator Set Warranty applies only when the

generator set is installed in a recreational vehicle.

The installer bears sole responsibility for the selection of the appropriate generator set, for its proper

installation, and for obtaining approvals from the authorities (if any) having jurisdiction over the installation.

The generator sets meet the basic requirements of the Standard for Safety for Engine Generator Sets for

Recreational Vehicles, ANSI/RVIA EGS-1 and are suitable for installation in accordance with:

• ANSI A1192 (NFPA No. 501C)—Recreational Vehicles

• NFPA No. 70, Article 551—Recreational Vehicles and RV Parks

• CSA Electrical Bulletin 946—Requirements for Internal Combustion Engine-Driven Electric

Generators for Use in Recreational Vehicles

Federal, state, and local codes, such as the California Administrative Code—Title 25 (RV installation),

might also be applicable. Installation codes and recommendations can change from time-to-time and are

different in different countries, states, and municipalities. Obtain the standards listed in the table below for

reference.

TABLE 1. REFERENCE CODES AND STANDARDS

Code of Federal

Regulations, Title 49:

Chapter III and

Chapter V

Superintendent of Documents

P. O. Box 371954

Pittsburgh, PA 15250-7954

NFPA 58, 70, 1192

National Fire Protection Association

470 Atlantic Avenue

Boston, MA 02210

ANSI/RVIA-EGS-1

Recreational Vehicle Industry Association

14650 Lee Road

Chantily, VA 22021

California

Administrative

Code—Title 25,

Chapter 3

State of California Documents Section

P.O. Box 1015

North Highlands, CA 95660

CAN/CSA-Z240

Recreational Vehicles

Bulletin 946

Canadian Standards Association Housing and Construction Materials Section

178 Rexdale Blvd.

Rexdale, Ontario, Canada M9W 1R3

SAE J1231, J1508,

J2044, J2599

SAE World Headquarters

400 Commonwealth Drive

Warrendale, PA 15096

2. Introduction5-2017

2.4 Electromagnetic Compatibility Compliance

Generator sets emit and receive electromagnetic (radio frequency) energy. If the generator set affects

operation of nearby devices, or nearby devices affect generator set operation, increase the distance

between them.

When used in countries where compliance to the EMC directive is required: This generator set has been

evaluated for use in the residential, commercial, and light industrial environments.

2.5 Specifications

2.5.1 Diesel Model Specifications

TABLE 2. DIESEL MODEL SPECIFICATIONS

HDKCA HDKCB

GENERATOR SET CONTROL: Integrated Microprocessor-Based Engine and Generator Control

GENERATOR: Single-Bearing, 4-Pole Rotating Field, 1800 RPM

Power (@1.0 power factor) 10,000 Watts

12,500 Watts

1,2

Frequency 60 Hz 60 Hz

Voltage 120/240 Volts 120/240 Volts

Number of Phases 1 1

Current 41.7 Amps 52.0 Amps

Line Circuit Breaker 2-pole, 45 Amp 2-pole, 50 Amp

FUEL CONSUMPTION:

No Load 1.2 l/h (0.33 gph) 1.4 l/h (0.38 gph)

Half Load 2.0 l/h (0.54 gph) 2.7 l/h (0.71 gph)

Full Load 3.0 l/h (0.78 gph) 4.8 l/h (1.28 gph)

ENGINE: 3-Cylinder In-Line, Water-Cooled, Indirect-Injection (IDI), 4-Stroke Cycle Diesel

Bore 83mm (3.27 in) 83mm (3.27 in)

Stroke 92.4mm (3.64 in) 92.4mm (3.64 in)

Displacement 1499cm

(91.44 in

) 1499cm

(91.44 in

)

Compression Ratio 23.0:1 23.0:1

Fuel Injection Timing (BTDC) 14.25° 14.25°

Firing Order 1-3-2 1-3-2

Fuel Nozzle Injection Pressure 13.731mPa (1991 psi) 13.731mPa (1991 psi)

Cylinder Compression Test 2.55mPa (370 psi) minimum 2.55mPa (370 psi) minimum

Valve Lash: Intake and Exhaust (cold)

0.18 to 0.22mm (0.0071 to 0.0087

in)

0.18 to 0.22mm (0.0071 to 0.0087

in)

Oil Capacity 5.6 liters (5.9 qt) 5.6 liters (5.9 qt)

2. Introduction 5-2017

HDKCA HDKCB

Cooling System Capacity 6.2 liters (6.6 qt) 6.2 liters (6.6 qt)

DC SYSTEM:

Nominal Battery Voltage 12 Volts 12 Volts

Minimum Battery Capacity CCA (Cold

Cranking Amps)

475 Amps down to –17 °C (0 °F)

650 Amps down to –29 °C (–20

°F)

475 Amps down to –17 °C (0 °F)

650 Amps down to –29 °C (–20

°F)

Battery Recharging Installer must provide Installer must provide

INSTALLATION:

Weight 348kg (767 lbs) 357kg (787 lbs)

Size (L x W x H)

1051 x 622 x 685mm

(41.4 x 24.5 x 27 in)

1051 x 622 x 685mm

(41.4 x 24.5 x 27 in)

Sound

70 dB(A) @ 3m (10 ft) and 54

dB(A) @ 15m (50 ft)—in "free

field site" @ half load

70 dB(A) @ 3m (10 ft) and 54

dB(A) @ 15m (50 ft)—in "free

field site" @ half load

1. Maximum power capability decreases 3.5% for each 305m (1000 ft) above 152.4m (500 ft) and 1% for each 5.5 °C

(10 °F) increase in ambient temperature above 25 °C (77 °F).

2. Ratings are at intermittent power output. Continuous power is 95% of rated power.

2.6 List of Acronyms

TABLE 3. ACRONYM DEFINITIONS

Acronym Definition

A/C Air Conditioning

AC Alternating Circuit

AGS Automatic Generator Start

BS Build Standard

CARB California Air Resource Board

CB Circuit Breaker

CCA Cold Cranking Amp

CM Commercial Mobile

CO Carbon Monoxide

DC Direct Current

EMI Electromagnetic Interface

EPA Environmental Protection Agency

GFCI Grounded Fault Circuit Interrupters

HV High Voltage

2. Introduction5-2017

Acronym Definition

LED Light-emitting Diode

LOP Low Oil Pressure

LPG Liquid Petroleum Gas

LV Low Voltage

NFPA National Fire Protection Agency

RV Recreational Vehicle

RVIA RV Industry Association

SAE Society of Automotive Engineers

SAI Secondary Air Injection

TABLE 4. ACRONYMS FOR UNITS OF MEASUREMENT

Acronym Definition

Amp Ampere

C Celsius

dBA Decibel A-Weighted

F Fahrenheit

Hz Hertz

kW kilowatt

lb Pound

M Meters

mm millimeters

RPM Revolutions per Minute

V Volts

VAC Volts Alternating Current

VDC Volts Direct Current

W Watts

This page is intentionally blank.

2. Introduction 5-2017

3 Location, Mounting, and Ventilation

The location, mounting, and ventilation of a generator set must be such that mounting is secure, engine

exhaust and fuel vapors are prevented from entering the vehicle, rain and road debris are prevented from

entering the generator set, and ready access is afforded for operating the generator set and performing

periodic maintenance.

3.1 Location

Typical locations for generator set installation are shown below.

• The location must provide:

◦ Ready access for starting and stopping the generator set and performing all periodic

maintenance.

◦ Separation from sources of flammable vapors, such as batteries and fuel tanks, which the

generator set could ignite.

◦ Access for connecting and disconnecting fuel lines, battery cables, remote control wiring, and

AC wiring.

◦ Access for removing the two fuel pump mounting screws so that the generator set does not

have to be removed to replace the fuel pump. See Figure 2.

◦ Access from below for draining engine oil.

◦ Unobstructed space below the generator set for proper cooling air flow.

• The generator set must not share a compartment or ventilation with batteries or fuel tanks. An

operating generator set can ignite flammable vapors. Make sure that in the first 305 mm (12 in) of

ground clearance there is at least 152.4 mm (6 in) of unobstructed space below the generator set

and open on at least three sides, which is required for proper cooling air flow.

• Locate or shield the generator set cooling air openings from direct rain, road splash and debris

thrown up by the road wheels.

NOTICE

Mudflaps, air ducts, and deflectors must be used to prevent road debris and tire spray from

going into the generator set.

• The generator set housing is not rain proof. If the generator set is installed where snow and rain will

hit the top of the generator set, a sheet metal or plastic cover should be used to prevent large

amounts of water from running in the seams of the generator set housing.

• Space to mount the generator set with at least 12.7 mm (1/2 in) clearance at the top and any side of

the generator set. Minimum clearances apply to any thermal or acoustic insulation with which a

compartment may be lined.

• Locating a generator set more than 5 feet above the floor and at the very back of the vehicle can

result in 'g' forces imparted to the generator set that causes physical damage to it as it travels down

the road. Generator sets located in these areas do not have warranty coverage for damage

resulting from high 'g' loads.

• Locating the generator set near the front of the coach or vehicle (directly behind or under the driver

or passenger seat) creates a situation where heat from the running propulsion engine can be drawn

into the generator set while stationary or moving. An alternate location should be selected for the

generator set.

3. Location, Mounting, and Ventilation 5-2017

• The generator set and exhaust must not be within 18 inches of a LP fuel tank without the use of

proper heat shielding. Refer to local codes and standards for additional information.

3.1.1 Typical Generator Set Locations - Class A RV

FIGURE 1. TYPICAL GENERATOR SET LOCATIONS - CLASS A RV

3.1.2 Typical Generator Set Locations - Class C RV

FIGURE 2. TYPICAL GENERATOR SET LOCATIONS - CLASS C RV

3.2 Mounting

WARNING

The generator set support structure must be designed and installed to support and restrain the

dynamic weight of the generator set. Failure to do so can result in the generator set dropping

onto the roadway causing property damage, severe personal injury, or death.

CUMMINS QD 10000 HDKCA, QD 12500 HDKCB Installation guide

Related papers

Other documents