Comtrend WAP-60AX Installation guide

Comtrend
Brand
Comtrend
Model
WAP-60AX
Type
Installation guide

Comtrend WAP-60AX is a high-performance WiFi 6 mesh-enhanced extender that boosts your existing network to eliminate dead zones and provide seamless coverage throughout your home. With speeds up to 4200 Mbps, it's ideal for 4K streaming, gaming, and other bandwidth-intensive applications. The WAP-60AX features a built-in 2.5 Gigabit Ethernet port for fast wired connections to your devices, and it's easy to set up using the WPS button or the Comtrend app.

Comtrend WAP-60AX is a high-performance WiFi 6 mesh-enhanced extender that boosts your existing network to eliminate dead zones and provide seamless coverage throughout your home. With speeds up to 4200 Mbps, it's ideal for 4K streaming, gaming, and other bandwidth-intensive applications. The WAP-60AX features a built-in 2.5 Gigabit Ethernet port for fast wired connections to your devices, and it's easy to set up using the WPS button or the Comtrend app.

! ! ! ! !Page 1
Quick Install Guide
WAP-60AX WiFi AX4200 Mesh-Enhanced Extender
Understanding the WAP-60AX
LED
LED Status
Description
Power
GREEN
On
The device is powered up.
Off
The device is powered down.
RED
On
There has been a POST (Power On Self Test) failure (not bootable) or device malfunction A
malfunction is any error of internal sequence or state that will prevent the device from normal
operation.
5G
GREEN
On
(5GHz) Wi-Fi is enabled in AP mode.
(5GHz) Wi-Fi is connected with an AP in Repeater mode.
Off
(5GHz) Wi-Fi is disabled in AP mode.
(5GHz) No connection in Repeater mode.
Blink
(5GHz) Wi-Fi is transmitting/receiving.
2.4G
GREEN
On
(2.4GHz) Wi-Fi is enabled in AP mode.
(2.4GHz) Wi-Fi is connected with an AP in Repeater mode.
Off
(2.4GHz) Wi-Fi disabled in AP mode.
(2.4GHz) No connection in Repeater mode.
Blink
(2.4GHz) Wi-Fi is transmitting/receiving.
WPS
GREEN
On
(2.4GHz+5GHz) WPS connection is successful.
Off
No WPS association process is ongoing.
Blink
(2.4GHz+5GHz)WPS connection is in progress.
AP
GREEN
On
The device is working in AP mode.
Off
The device is not working in AP mode.
Repeater
GREEN
On
The device is working in Repeater mode.
Off
The device is not working in Repeater mode.
2.5GE
GREEN
On
The 2.5 Gigabit Ethernet is connected.
Off
The 2.5 Gigabit Ethernet is not connected.
Blink
The 2.5 Gigabit Ethernet is transmitting/receiving.
Port/Button
Description
Reset
Factory Reset Function: Press and hold this button for over 10 seconds.
LAN
Optional: Use this port to connect an Internet- enabled device (e.g. laptop, set-top-box, etc.).
A
AP/Repeater Switch
On/Off Button
Reset Button
LED Details are
Below
! ! ! ! !Page 2
Initial Device Setup via Ethernet Pairing
NOTE: The following application uses a WAP-60AX in Extender Mode along
with a Comtrend Gateway to create a proper connection. For instructions
on additional setup applications, please visit us online using the QR Code
at the bottom of Page 2.
1. Setup the WAP-60AX by plugging the power adapter into it and
connecting it to an outlet. Press the Power Button to the ON position
(IN). Set the WAP-60AX to Repeater Mode by sliding the AP/Repeater
Switch to the down position.
2. Use the included Ethernet cable to connect one end into the LAN port
of the Comtrend Gateway and the other end into the LAN port of the
WAP-60AX. Wait until the WAP-60AX’s Repeater LED is solid GREEN. This
could take anywhere between 2-8 minutes. Once solid GREEN, the
WAP-60AX is successfully paired with the Comtrend Gateway.
3. After the WAP-60AX is paired, move it to the nearest outlet where
additional WiFi coverage is needed. Once it is plugged in, the Repeater
LED should light up solid GREEN. This may take another 2-8 minutes.
4. If you are setting up more than one WAP-60AX, then please follow instructions 1-3 with the additional WAP-60AX units.
Your WAP-60AX is now setup! Enjoy!
Troubleshooting
The following information should help you diagnose basic setup or installation problems.
POWER Indicator is OFF: If the Power LED goes off, please make sure that your power outlet is working properly (perhaps by testing with another
device). Then, plug in your WAP-60AX again and make sure to press the Power Button to the ON position (IN).
2.5G ETHERNET LED is OFF: If the 2.5G ETHERNET LED fails to light up, check that the LAN port of the WAP-60AX unit is connected firmly to the LAN port
of the other device. To check the condition of the Ethernet cable, use another cable to test the same connection.
WPS LED is OFF: If the WPS LED(s) fails to light up, press and release the WPS Button on the device setup in AP Mode. Within two minutes press and
release the WPS Button on the device setup in Repeater Mode (during this time both WPS LEDs will blink). Upon successful connection the WPS LEDs
will light up solid GREEN on both of the Wireless Access Points.
AP LED is OFF: WAP-60AX in Repeater Mode. Set the Wireless Access Point to AP Mode by sliding the AP/Repeater Switch to the up position.
REPEATER LED is OFF: WAP-60AX in AP Mode. Set the Wireless Access Point to Repeater Mode by sliding the AP/Repeater Switch to the down position.
RESET: If you have tried the above and are still experiencing problems, you can reset both devices to factory default by using a pin to push in the
Reset Button for more than 5 seconds, then release the button.
FOR MORE HELP: For instructions on advanced features such as changing the WiFi settings, FAQ, etc., please visit our product online at:
http://us.comtrend.com
YouTube Channel: https://www.youtube.com/user/ComtrendConnection
Facebook: https://facebook.com/Comtrend
Support: Visit our website or call (949) 753-9640
For additional setup instructions, please scan the below QR Code and click “Resources.”
Link to: https://us.comtrend.com/wap-60ax-wifi-6-mesh-enhanced-extender/
B
C
D
WAP-60AX
Comtrend Gateway
  • Page 1 1
  • Page 2 2

Comtrend WAP-60AX Installation guide

Comtrend
Brand
Comtrend
Model
WAP-60AX
Type
Installation guide

Comtrend WAP-60AX is a high-performance WiFi 6 mesh-enhanced extender that boosts your existing network to eliminate dead zones and provide seamless coverage throughout your home. With speeds up to 4200 Mbps, it's ideal for 4K streaming, gaming, and other bandwidth-intensive applications. The WAP-60AX features a built-in 2.5 Gigabit Ethernet port for fast wired connections to your devices, and it's easy to set up using the WPS button or the Comtrend app.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents