GARO 380280 User manual

Type
User manual

GARO 380280 is a pole-mount fixture designed for easy installation of GARO Entity PRO charging stations. It can accommodate one or two charging stations, making it suitable for various EV charging scenarios. The fixture is compatible with 60 mm poles and features pre-drilled holes for secure mounting. It also includes cable grommets to ensure proper cable management and protection. With its sturdy construction and ease of use, GARO 380280 offers a reliable solution for EV charging infrastructure.

GARO 380280 is a pole-mount fixture designed for easy installation of GARO Entity PRO charging stations. It can accommodate one or two charging stations, making it suitable for various EV charging scenarios. The fixture is compatible with 60 mm poles and features pre-drilled holes for secure mounting. It also includes cable grommets to ensure proper cable management and protection. With its sturdy construction and ease of use, GARO 380280 offers a reliable solution for EV charging infrastructure.

Art no:380280
Pole mount fixture
Entity PRO
Installation instructions
2
EN
About this manual
The purpose of this manual is to provide you with the neces-
sary information to install the pole attachment for the Entity
PRO models Charging stations.
This document contains general descriptions which are
verified to be accurate at the time of printing. However,
because continuous improvement is a goal at GARO, we
reserve the right to make product modifications at any time.
Product function description.
GARO offers two pole mount fixtures. The charging stations
will be centered on the Pole.
The EPPFS is the first choice when you install a single GARO
Entity PRO Charging Station.
The EPPFD is the first choice when you install two GARO
Entity PRO charging station back-to-back.
It is possible to install two GARO Entity PRO charging sta-
tions back-to-back on a EPPFS, but a “daisychain” installa-
tion (where one cable is used from one pole to another) is
easier to implement with the EPPFD
Tools and equipment needed
Torx driver (T25, T30)
Wrench (8 mm)
Flat screwdriver
Power cable
Ethernet cable*
Control cable*
* If applicable
To install the Entity PRO
charging station
This manual does not contain instructions on how to install
a Garo Charging station. To install the Entity PRO charging
station refer to the installation manual. The installation of a
charging station must be done by an authorized electrician.
Follow national regulations.
Pole
Any 60 mm tube can be used to mount the pole mount
fixture. Poles and ground anchors can be ordered from
www.garo.se.
Make sure that the pole is firmly attached to the ground
before you attach the pole mount fixture.
Dimensions
EPPFS
88 mm
427 mm
160 mm
427 mm
EPPFD
EN
3
1. Install the Pole mount fixture
The mounting process and toques used are the same for
both the single and double pole mount fixtures .
Before you start the installation, make sure that the ca-
bles are prepared and positioned according to national
regulations.
60 mm
1
Note: Make sure that the pole is attached firmly to the
ground.
2
Note: The short screws are for single CS installation and
the longs screws are for double CS installation.
3
6 Nm
4
4
EN
5
A
B
6
Note: Only if an ethernet cable (RJ45) (A) and/or a
control cable (B) is used.
7
6 Nm
8
EN
5
3
Note: Only if you install two CS on the pole mount
fixture. Do this on installation brackets of the charging
stations. Use a cable grommet to seal the hole to the
steelplate.
2. Prepare the CS bracket for
installation on the pole mount
fixture
1
Note: Only if an ethernet cable is used.
2
Note: Only if an control cable is used.
6
EN
3. Attach CS bracket(s) to the
pole mount fixture
You can attach one or two charging station(s) to both
the single (EPPFS) and the double (EPPFD) pole mount
fixture. The double version (EPPFD) is recomended for
daisychaining (when several CS & poles are installed
using the same power cable)
3.1 Attach a CS bracket to the single
(EPPFS) pole mount fixture
4 Nm
1
Note: A second CS can be installed on the back of the
mounting plate of the pole mount fixture. In that case the
long screws must be used.
3.2 Attach two CS brackets to the double
(EPPFD) pole mount fixture
1
Note: Only remove the water protection plate when
you attach two CS on the pole attachment.
4 Nm
4 Nm
A
B
2
Note: Thread the cables through CS bracket (A) before
you attach the bracket to the pole mount fixture and CS
bracket (B).
EN
7
4. Cable routing
There are several ways (depending on the CS version)
to route the power cables when you install two charging
stations and plan for daisy-chaining. Make sure that
cable grommets are used at the holes of the incoming
and outgoing power cables.
Note: For outlet versions only: Do not pinch the power
cable wires. Do not route the wires on the same side of
the connection terminal as the outlet.
8
EN
9
EN
GARO E-Mobility AB
Box 203
335 33 Gnosjö, Sweden
Phone +46 370 332 00
info@garo.se
www.garo.se
GARO Finland Oy
Itälahdenkatu 18 a,
FI-00210 HELSNKI, Finland
Telephone: +358 20 752 9030
E-mail: myynti@garo.fi
www.garo.fi
GARO Electric Ireland Ltd
19/307 Northwest Business Park,
Blanchardstown, IE-DUBLIN 15, Irland
Telephone: +35 31 882 00 30
E-mail: info@garo.ie
www.garo.ie
GARO AS
Sankt Hallvardsvei 3,
NO-3414 LIERSTRANDA, Norway
Telephone: +47 32 89 64 50
E-mail: gar[email protected]
www.garo.no,
GARO Polska Sp z.o.o.
Wislawy Szymborskiej 18,
PL-70-784 SZCZECIN, Poland
Telephone: +48 91 881 17 70 , +48
91 424 33 35
Email: info@garo.com.pl
www.garo.com.pl
GARO Electric Ltd
Sales & Customer Service
Unit 16 Urban Express Park,
Aston Hall Road,
Birmingham,
B6 7FH
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

GARO 380280 User manual

Type
User manual

GARO 380280 is a pole-mount fixture designed for easy installation of GARO Entity PRO charging stations. It can accommodate one or two charging stations, making it suitable for various EV charging scenarios. The fixture is compatible with 60 mm poles and features pre-drilled holes for secure mounting. It also includes cable grommets to ensure proper cable management and protection. With its sturdy construction and ease of use, GARO 380280 offers a reliable solution for EV charging infrastructure.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI