INPUT VOLTAGE: 9v/3a 12V/2.5
Aairpods output: 1-3w
USB OUTPUT: 5V 2A
Frequency: 110-205KHZ
net weight: 420g
DUAL COIL WIRELESS CHARGING OUTPUT:
5W, 7.5 W, 10W, 15w
Led power: 2W
MATERIAL: ABS + PC
Product Size: 228 * 142 * 23.5 mm
Parameter
specification
Charging mode Points to note
IPHONE:iPhone 13/13 Pro/13 Pro Max/12/12 Pro/12 Pro Max/11/11
Pro/11 Pro Max/Xs/Max/Xr/X/8/8 Plus
Samsung：Galaxy S20/S20+ /S20 Ultra/S 10/S10+/S9/S9+/S8/S8+/S7/S7
edge/S6 edge Plus/Note 10/9/8/7/5
Any phone that supports Qi wireless charging。
Please pay attention to the following issues, otherwise it may
lead to abnormal charging, high charging temperature, intermit-
tent charging, or even non-charging.
1. Use QC2.0/3.0 quick charger adapter (9v/3a) for better
charging performance. 5v/1a adapters are not supported.
2.This product supports the QC and PD protocols.
3.Touch the switch button, click on the light to turn on/off, and
switch the light level.
4.For wireless charging, there should be no metal or magnetic
objects within a distance of 4cm from the center point on the
back of the phone.
5.The lower the temperature, the faster the charge. Charging
speed is faster in winter than in summer.
6.Please do not charge in the hot and humid environment to avoid
circuit damage.
7.Please keep it out of the reach of children to avoid unneces-
sary accidents.
Compatibility Configuration list
Wireless Charger, charging cable, user manual
The instruction and pictures are the sketch map,
the final product is subject to the physical object.
Thank you for your purchase of our products, this product is a
smart phone wireless charger, allowing you to easily experience
the fun of digital products.
Please read this user manual carefully before using this
product and keep it properly for reference.
SWITCH/LAMP dimming adjustment
Atmosphere Lamp
AirPuds wireless charging station
(also can charge mobile phone)
You can fold it up
Wireless charging station
Clock (24-hour system)
It can be used for storage
Schematic
diagram
Cooling Hole
6 silicone pads
Made in China
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority
to operate the equipment.
This device complies with Part 15 of the FCC Rules.Operation
is subject to the following two conditions:
(1)this device may not cause harmful interference,and
(2)this device must accept any interference received,including
interference that may cause undesired operation.
Note:This equipment has been tested and found to comply with the
limits for a Class B digital device,pursuant to Part 15 of the
FCC Rules.These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates,uses,and can radiate radio
frequency energy,and if not installed and used in accordance with
the instructions,may cause harmful interference to radio
communications.However,there is no guarantee that interference
will not occur in aparticular installation.If this equipment does
cause harmful interference to radio or television reception,which
can be determined by turning the equipment off and on,the user is
encouraged to try to correct the interference by one or more of
the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
–Consult the dealer or an experienced radio / TV technician for help.
FCC Requirement
1
TORRAS CTEZ100 User guide
DesertWest CTEZ100 User manual
VICSEED CTEZ100 User manual
LUNAR ARTEFACTS PULSE VOLITARI Wireless Charger User guide
Itek MP-132A User manual
Veho UF-2 User manual
IBD T11 User manual
Mio S20 User manual
NAUTICA S20 Portable Wireless Speaker User manual
CHOETECH T575-F 2-in-1 Magnetic Wireless Charging Stand User manual
