Dinan D280-0025 User manual

Type
User manual

Dinan D280-0025 Rear Toe Link Kit enhances your vehicle's performance and durability. Specifically designed for various BMW models, it provides precise rear toe adjustment, eliminating the need for factory eccentrics. Experience improved handling, stability, and tire wear with this professional-grade upgrade. Installation requires removing the stock rear toe links and replacing them with Dinan's pre-set links. Detailed instructions and necessary hardware are included.

Dinan D280-0025 Rear Toe Link Kit enhances your vehicle's performance and durability. Specifically designed for various BMW models, it provides precise rear toe adjustment, eliminating the need for factory eccentrics. Experience improved handling, stability, and tire wear with this professional-grade upgrade. Installation requires removing the stock rear toe links and replacing them with Dinan's pre-set links. Detailed instructions and necessary hardware are included.

INS280-0025 Page 1 of 3 Rev. 04/21/23
REAR TOE LINK KIT
INSTALLATION INSTRUCTIONS
PART NUMBER D280-0025
APPLICATION: 2022-23 G42 M240i & xDrive
2022-23 G42 230i & xDrive
2020-23 G20 M340i & xDrive
2019-23 G20 330i & xDrive
2021-23 G22/G23 M440i & xDrive
2022-23 G26 M440i & xDrive
2021-23 G22/G23 430i & xDrive
2022-23 G26 430i & xDrive
2019-23 G29 Z4 30i
2020-23 G29 Z4 M40i
2020-23 A90/A91 Supra 3.0L
2021-23 A90/A91 Supra 2.0L
Congratulations for being selective enough to use a Dinan Rear Toe Link Kit. We have
spent many hours developing this kit to assure that you will receive maximum
performance and durability with minimum difficulty in installation. Please take the time
to read these instructions and call us if you have any difficulties during the installation.
DO NOT WORK ON VEHICLES SUPPORTED BY A JACK ONLY. USE SECURE
JACK STANDS!
INS280-0025 Page 2 of 3 Rev. 04/21/23
________________________________________________________________
PARTS LIST
Qty Part # Description
2 D283-0039 Toe Link/Boots Assy
2 33 32 6 760 668 Nuts w/ flange
________________________________________________________________
INSTALLATION NOTES:
Some hardware may need to be replaced. Please review the factory procedure
and have those pieces on hand as needed.
An alignment will be required after installation of these links.
INSTALLATION:
1. Remove rear wheels.
2. Mark the positions of the toe adjustment eccentric bolts.
3. Remove the stock rear toe links per factory recommended procedure.
4. The two Dinan toe links have been preset to the correct length and do not require
adjustment at this time.
5. Install the Dinan rear toe links.
Be sure to start the bolts by hand a few turns first, to prevent cross-threading.
Use the new nuts provided.
6. Take care to align the eccentric bolts with the marks made in Step 2.
7. Torque fasteners to 74 ft-lbs.
8. Perform an alignment. There is no need to use the factory eccentrics to adjust the
rear toe. Adjust rear toe using the Dinan toe link for improved precision.
While holding the two main sections steady, loosen the two jam nuts on either
side of the center turnbuckle. Note that the nut near the “D” logo section has
left-hand threads.
Turn the center turnbuckle to adjust the overall length of the toe link.
Tighten jam nuts.
INS280-0025 Page 3 of 3 Rev. 04/21/23
  • Page 1 1
  • Page 2 2
  • Page 3 3

Dinan D280-0025 User manual

Type
User manual

Dinan D280-0025 Rear Toe Link Kit enhances your vehicle's performance and durability. Specifically designed for various BMW models, it provides precise rear toe adjustment, eliminating the need for factory eccentrics. Experience improved handling, stability, and tire wear with this professional-grade upgrade. Installation requires removing the stock rear toe links and replacing them with Dinan's pre-set links. Detailed instructions and necessary hardware are included.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI