Cygnett CY4058PPWIR User manual

Type
User manual

Cygnett CY4058PPWIR is a Qi-enabled wireless charger capable of delivering up to 15W of power, allowing for fast and efficient charging of compatible devices. It features multiple output modes, including 5W, 7.5W, 10W, and 15W, to accommodate different devices' power requirements. An indicator light provides visual feedback on the charging status, with solid green indicating active charging, solid red indicating a fully charged device, and flashing red indicating the detection of a foreign object.

Cygnett CY4058PPWIR is a Qi-enabled wireless charger capable of delivering up to 15W of power, allowing for fast and efficient charging of compatible devices. It features multiple output modes, including 5W, 7.5W, 10W, and 15W, to accommodate different devices' power requirements. An indicator light provides visual feedback on the charging status, with solid green indicating active charging, solid red indicating a fully charged device, and flashing red indicating the detection of a foreign object.

Installation instructions
charging device onto the wireless charging output (A) and your
device should begin to wirelessly charge automatically.
To achieve fast charging, please ensure you are using a charger that
is capable of fast charging at least 20W. For optimum charge speed,
adjust your device so that it is aligned to the centre of the wireless
charging output. Please ensure that the case on your phone is not
performance. Some cases interfere with wireless charging if they
contain metallic material or are overly thick.
AWireless output
B
A
B
Name PowerBase III 15W Wireless
Charger
Item Number CY4058PPWIR, CY4059PPWIR,
CY4060PPWIR, CY4061PPWIR
5.0V3.0A (15.0W), 9.0V2.22A
(20.0W), 12.0V1.67A (20.0W)
Wireless Output 5.0W, 7.5W, 10.0W, 15.0W (15.0W
Max)
Total output 15.0W Max
Working Frequency Band After evaluation, the product
exposure required while used
20cm away from the human body.
Max Output Power -18.5dBµA/m@10m
FCC ID 2AEDZCY40XXPPWIR
Caution
Please read all warnings for your safety and optimal user experience.
Please read and follow these instructions carefully and retain for
your records.
Do not expose to extreme weather conditions.
Do not use this product if you observe visible defects.
Do not short circuit the product or store it in a receptacle where
it may be short circuited by other metallic or conductive objects.
Do not operate the product if it has been wet or otherwise
damaged, to prevent against electric shock, explosion and/or
injury.
Never attempt to dismantle the unit.
Children should be supervised to ensure that they do not play
with the product.
Do not use if broken, damaged, or exposed to liquids.
Not to be used in extremely high ambient temperatures.
Do not use with damaged or faulty accessories.
Do not place close to a magnetic strip or strip card as it could
cause magnetic failure.
Please keep charger a safe distance of at least 80cm from any
implantable medial devices to avoid medical device interference.
In the case of the device overheating, place disconnect
immediately.
Please note
by the party responsible for compliance could void the user’s
authority to operate the equipment
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separate between the equipment and receiver.
that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
Cygnett and the Cygnett logo are trademarks of Cygnett Pty Ltd.
Other brands and product names are trademarks or registered
trademarks of their respective holders. Made in China.
Cygnett Pty Ltd,
858 Lorimer St, Port Melbourne,
Victoria, 3207, Australia
Cygnett UK Limited,
London, WC2H 9JQ
Cygnett USA Inc,
3838 W Carson St,
Ste 220, Torrance, CA 90503
Cygnett EU,
2718RD Zoetermeer, The Netherlands
PowerBase III
15W Wireless Charger
USER MANUAL
Indicator Light Status
Flashes 3 times and Powered on and on standby
Solid green Wirelessly charging a device
Solid red Fully charged a device
Flashing Red Foreign object detected on
wireless output
FCC RF RADIATION EXPOSURE STATEMENT CAUTION
To maintain compliance with the FCC’s RF exposure guideline, place
the product at least 20cm from nearby persons.
112-205
  • Page 1 1

Cygnett CY4058PPWIR User manual

Type
User manual

Cygnett CY4058PPWIR is a Qi-enabled wireless charger capable of delivering up to 15W of power, allowing for fast and efficient charging of compatible devices. It features multiple output modes, including 5W, 7.5W, 10W, and 15W, to accommodate different devices' power requirements. An indicator light provides visual feedback on the charging status, with solid green indicating active charging, solid red indicating a fully charged device, and flashing red indicating the detection of a foreign object.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI