Alto-Shaam COMBITOUCH SERIES 6•10ESG Technical & Service Manual

TECHNICAL SERVICE MANUAL

COMBITHERM®

GAS

How to Use this Technical Service Manual

This manual has been compiled as a complete resource for a technician working on Combitherm Gas models. It includes

necessary product information and drawings, along with helpful troubleshooting procedures.

Introduction gives a quick overview of the Combitherm Gas line to aid in model identification.

Sections 1 through 5 contain information applying to all Combitherm Gas models:

– CONTROL PANEL IDENTIFICATION includes information on using the controllers and operating instructions. It is

the same material supplied to the customer.

– PREVENTIVE MAINTENANCE includes procedures for cleaning. This information is also supplied to the customer.

– SERVICE MODE AND ERROR CODES explains the special programming available to you as a technician to view

status, make adjustments and test functions on models equipped with Standard and Deluxe Controllers. Information is

also included on the use of displayed error codes to resolve problems and on the functions that can be operated under

fault conditions.

– TROUBLESHOOTING TREES are provided for the most common conditions you will be required to address.

– COMBITHERM PARTS has drawings and lists of available parts that are common to all gas models.

Sections 6 through 12 contain information that is specific to each model:

– The model’s Technical Data Sheet

– Parts Information that is unique to the model, including its door, condensation tank and pressure box

– Wiring Diagrams

– Ladder Diagrams

Navigation

On this CD, starting with the Main Table of Contents on the following page, you may click on any item that has a page

number and quickly jump to the information you need. Note that you may Return to the Main Table of Contents from the

bottom of any Section Contents page.

Printing

From this CD, you may print the Current Page or any range of pages. If you would like to print out a complete manual for

a specific model, print pages 1 – 78 (Sections 1 – 5) along with the pages in that model’s section (6.10 ESG, for example).

Here’s a tip: Because printers vary in their capacity to handle large drawings, make a test print of one of the Wiring

Diagrams before printing the model’s section.

COMBITHERM GAS TECHNICAL S ERVICE M ANUAL

TABLE OF CONTENTS
How to Use this Technical Service Manual...................................... 2
Introduction.................................................................................. 4
1 — Control Panel Identification.................................................. 5
2 — Preventive Maintenance....................................................... 49
3  — Service Mode and Error Codes............................................. 57
4 — Troubleshooting Trees ......................................................... 63
5 — Combitherm Parts............................................................... 73
6 — 6.10 ESG........................................................................... 79
7 — 10.10 ESG......................................................................... 87
8 — 7.14 ESG........................................................................... 95
9 — 10.20 ESG......................................................................... 103
10-— 12.18 ESG......................................................................... 111
12-— 20.20 ESG......................................................................... 119
COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 3

MODEL NUMBERS

This manual covers the following gas models:

CONTROLLERS

• Standard is a touch key controller.

• Deluxe is a touch key controller with programmable Rapid-Touch™ keys.

• S-Control is rotary dial controller.

FEATURES AND OPTIONS

• Recessed Door is available on all models.

• Smoker Mode is available on all models.

• Delta-T Probe (single point) is standard on models with standard or deluxe controllers.

Multi-point Probe is an option for those models.

• Core Temp Probe (single point) is optional on S-control models.

MODES

The Combitherm combination oven/steamer is a multipurpose oven used for:

COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 4

INTRODUCTION

STEAM MODE

COMBINATION MODE

CONVECTION MODE

RETHERM MODE

CORE TEMPERATURE MODE

Gas Models

6.10ESG 10.20ESG

10.10ESG 12.18ESG

7.14ESG 20.20ESG

Standard and Deluxe Control......................................................... 6

S-Control ..................................................................................... 45

Return to Main Table of Contents .................................................. 3

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 5

1

CONTROL PANEL IDENTIFICATION

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 6

 POWER ON/OFF KEY

 STEAM MODE KEY

 PROGRAMMED MENU KEY

 COOKING TEMPERATURE KEY

 DOWN ARROW KEY

 MOISTURE VENT KEY

 START / STOP KEY

 CHEF FUNCTION KEY

 TIME KEY

 COMBINATION MODE KEY

RETHERM MODE KEY 

CONVECTION MODE KEY 

PROGRAM INSTALL/EDIT KEY 

FUNCTION & OPERATING 

CONTROL PANEL DISPLAY 

CORE TEMPERATURE KEY 

UP ARROW KEY 

RAPID-TOUCH KEYS 

INDICATORS

DELUXE MODELS ONLY

ELECTRIC MODELS ONLY

CONTROL PANEL IDENTIFICATION

STANDARD

AND PROGRAMMABLE DELUXE MODELS

 ADJUSTMENT KNOB

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 7

STANDARD & DELUXE CONTROL PANEL BASIC FUNCTION



POWER ON/OFF KEY

Activates power to the oven and automatically fills

the steam generator equipped models with water

that will heat to a stand-by mode temperature of

150°F (65°C). The steam generator flush is also

activated by pressing this key.

 STEAM MODE KEY

The oven will operate in the steam mode at a

temperature range of 86°F to 248°F

(30°C to 120°C).

• Automatic steaming at 212°F (100°C)

FACTORY-SET DEFAULT.

• Quick steaming between 213°F and 248°F

(101°C and 120°C).

• Low Temperature Steaming between

86°F and 211°F (30°C and 99°C).

 START/STOP KEY

Initiates all cooking mode functions and

programmed procedures stored in memory.

Stops an activated cooking mode or

programmed procedure currently in progress,

and exits the Chef function key

.

 COMBINATION MODE KEY

Selection key for cooking with a combination

of steam and convection heat that can be set

within a temperature range of 212°F to 482°F

(100°C and 250°C).

 PROGRAMMED MENU KEY

Used to access and exit a menu list of all

stored cooking programs that can be reviewed

in display

. DELUXE MODELS ONLY

 CHEF FUNCTION KEY

Used to select programmed menu functions,

various auxiliary functions, and several chef

help instructions.

 COOKING TEMPERATURE KEY

Used to set the required cooking temperature,

to recall the set cooking temperature, or to

check the actual oven temperature in

conjunction with the down arrow key

, the

up arrow key

 or the adjustment knob .

 TIME KEY

Used to set the required cooking time or recall

the set cooking time in conjunction with the

down arrow key

, the up arrow key , or

the adjustment knob

.

 DOWN ARROW KEY

Used to decrease displayed cook temperature

, time , or core temperature  and as a

scrolling key for programming functions.

 ADJUSTMENT KNOB

Displays oven functions. Serves the same

function as the up and down arrow keys to

increase or decrease the displayed cook

temperature

, time , or core temperature .

 MOISTURE VENT KEY ELECTRIC MODELS ONLY

Immediately vents steam and condensate from the

oven compartment while cooking in the Convection

mode

 or in the Combination mode .

 RETHERM MODE KEY

Food rethermalization or reheating mode will

operate with automatic steam injection at a

temperature range of 248°F and 320°F

(120°C and 160°C).

 CONVECTION MODE KEY

Selection key for convection cooking without

steam at a temperature range of 86°F to 482°F

(30°C and 250°C).

 PROGRAM INSTALL AND EDIT KEY

Used to create, change, duplicate, and delete

programmed menus.

DELUXE MODELS ONLY.

 • • • • • • • CONTROL PANEL DISPLAY

 CORE TEMPERATURE KEY

Used to set the required internal product

temperature, to recall the internal product

temperature set by the operator, or to display

the current internal temperature of the product

in conjunction with the down arrow key

, the

up arrow key

, or the adjustment knob .

 UP ARROW KEY

Used to increase displayed cook temperature

, time , or core temperature  and as a

scrolling key for programming functions.

 • • • • • • • RAPID-TOUCH KEYS DELUXE MODELS ONLY.

One-touch cooking for immediate access to

frequently used operator set programs including

cooking modes, cleaning, and other oven functions.

CONTINUED

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 8

 FUNCTION & OPERATING INDICATORS

A. GOLD-N-BROWN FEATURE

This indicator will illuminate when the browning function is set by the operator in a

timed or programmed cooking cycle in either convection mode or combination mode.

B. COMBI SMOKER (ON EQUIPPED MODELS)

This indicator will illuminate when the smoking function is set by the operator in a

timer, probe or programmed cooking cycle in either convection mode or combination

mode.

C. REDUCED FAN SPEED

This indicator will illuminate whenever the operator sets a reduced fan speed to

protect products affected by high-velocity air movement.

D. CONFIRMATION OF OVEN OPERATION

This indicator illuminates whenever the oven is operating in any mode.

E. KEY LOCK

This indicator will illuminate when operator has locked any mode key or function to

prevent unauthorized or accidental changes.

F. MOISTURE VENT

This indicator will illuminate whenever the Moisture Vent Key 

is pressed by the operator to eliminate excessive moisture.

G. ENERGY LOCK

FOR USE WITH OVENS INSTALLED UNDER AN ALTO-SHAAM VENTLESS HOOD.

This indicator is a safety feature that will illuminate and prevent the oven from being

operated unless the ventless oven hood is operating.

STANDARD & DELUXE CONTROL PANEL BASIC FUNCTIONS

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 9

SET UP MENU

Following installation, the control should be set with the date and time. In addition to the date and time,

the set-up function provides the operator with the ability to adjust a number of other Combitherm

operating conditions to conform with the needs of the individual installation.

SET-UP PROCEDURES

PRESS THE ON/OFF POWER KEY

TO THE ON POSITION.

PRESS THE CHEF FUNCTION KEY.

Rotate the adjustment knob

until the set up symbol is

highlighted within the display.

PRESS THE CHEF FUNCTION KEY.

Press the up  and down  arrow keys

or rotate the adjustment knob to select

“YES” for the set up function.

PRESS THE CHEF FUNCTION KEY TO

CONFIRM THE SET UP FUNCTION.

Press the up

 and down  arrow keys

or rotate the adjustment knob to

highlight one of the following

adjustment functions:

SET UP ADJUSTMENT CHOICES

SIGNAL TONE

VOLUME

TIME

DATE

PROGRAM INDEX

DEFAULT/MEMO SETTINGS

TEMPERATURE DISPLAY

NETWORK ADDRESS

LANGUAGE

SIGNAL TONE

Rotate the adjustment knob until the signal tone symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SIGNAL TONE SELECTION.

Press the up  and down  arrow keys or rotate the adjustment knob to select each tone offered.

Stop rotation at each individual setting to hear an audio playback. Select the tone desired.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SELECTED SIGNAL TONE SETTING.

Set up

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 10

ALWAYS BEGIN SET UP ADJUSTMENTS FROM THE SET UP MENU .

VOLUME

Rotate the adjustment knob until the volume symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE VOLUME SELECTION.

Press the up  and down  arrow keys or rotate the adjustment knob to select each volume level

offered. Stop rotation at each individual setting to hear an audio playback. Select the volume

desired with consideration of the noise level within the kitchen during peak production periods.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE VOLUME SETTING.

TIME

Rotate the adjustment knob until the time symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TIME SELECTION.

Press the up  and down  arrow keys to alternate between hours and minutes and rotate the

adjustment knob in each to adjust the numbers to the correct time.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SET TIME.

DATE

Rotate the adjustment knob until the date symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE DATE SELECTION.

Rotate the adjustment knob to select the preferred date format.

Press the up  and down  arrow keys to alternate between day, month and year, and rotate the

adjustment knob in each to adjust the numbers to the correct settings.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE SET DATE.

PROGRAM INDEX

Rotate the adjustment knob until the program index symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE PROGRAM INDEX SELECTION.

Press the up

 and down  arrow keys or rotate the adjustment knob to select the preferred index format:

“YES” for a listing of programs entered alphabetically with the program install/edit key.

“NO” for a listing of programs entered numerically with the program install/edit key.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE PROGRAM INDEX SETTING.

SET-UP PROCEDURES

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 11

SET-UP PROCEDURES

ALWAYS BEGIN SET UP ADJUSTMENTS FROM THE SET UP MENU .

DEFAULT/MEMO SETTING

Rotate the adjustment knob until the default/memo symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE DEFAULT/MEMO SELECTION.

Rotate the adjustment knob to “NO” for memo. This setting will display the last operator set values for

time and temperature in each cooking mode.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE MEMO SETTING.

TO CHANGE THE DEFAULT SETTINGS

Rotate the adjustment knob to select “YES”.

A numbered list of default descriptions will appear in the display. Rotate the adjustment knob

until the setting to be changed is highlighted. Press the up

 arrow key to highlight the time or

temperature to be changed. Rotate the adjustment knob to change the default to the setting

desired. Press the down  arrow key to save the new default setting.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE NEW DEFAULT SETTINGS.

COOKING

MODE

OVEN

TEMPERATURE

CORE

TEMPERATURE

COOKING

TIME

COMBITHERM FACTORY SET DEFAULT SETTINGS

DELTA-T 122°F 172°F

FREE

MODE (50°C) (77°C)

RETHERM 275°F 158°F

5 MINUTES

MODE (135°C) (70°C)

PREHEAT 374°F

FREE —

MODE (140°C)

CONVECTION 338°F 158°F

30 MINUTES

MODE (170°C) (70°C)

COMBINATION 302°F 158°F

70 MINUTES

STEAM MODE (150°C) (70°C)

STEAM 212°F 158°F

25 MINUTES

MODE (100°C) (70°C)

The default/memo setting allows the operator to choose

between a display showing the factory set defaults for

time and temperature or the last operator set values for

time and temperature in each cooking mode. This

adjustment function also allows the operator to change

the defaults from those set at the factory to settings that

better meet the needs of the individual operation.

Cooking product with operator set defaults for time and

temperature can help reduce operator error. Cooking

with the oven in the memo setting is particularly useful

when several batches are cooked in succession. The

memo setting eliminates the necessity to set time and

temperature for each batch.

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 12

ALWAYS BEGIN SET UP ADJUSTMENTS FROM THE SET UP MENU .

TEMPERATURE DISPLAY

Rotate the adjustment knob until the temperature display symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TEMPERATURE DISPLAY SELECTION.

Press the up  and down  arrow keys or rotate the

adjustment knob to select either Fahrenheit or Celsius.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE TEMPERATURE DISPLAY SETTING.

NETWORK ADDRESS

Press the up  and down  arrow keys or rotate the adjustment knob until the network address

symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE NETWORK ADDRESS SELECTION.

The current network address will appear in the display.

Rotate the adjustment knob to select 1 through 99 and assign

a different network number for each PC to be connected.

PRESS THE CHEF FUNCTION KEY TO CONFIRM EACH NETWORK ADDRESS.

LANGUAGE

Press the up  and down  arrow keys or rotate the adjustment knob

until the language symbol is highlighted within the display.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE LANGUAGE PROGRAM SELECTION.

Rotate the adjustment knob to select the required language.

PRESS THE CHEF FUNCTION KEY TO CONFIRM THE LANGUAGE SETTING.

CHINESE

DUTCH

ENGLISH*

FRENCH

GERMAN

ITALIAN

JAPANESE

KOREAN

POLISH

PORTUGUESE

RUSSIAN

SPANISH

SWEDISH

*U.S. FACTORY SETTING

NOTE

: SOME OF THE LANGUAGE SELECTIONS SHOWN ABOVE MAY NOT BE AVAILABLE ON ALL MODELS.

SET-UP PROCEDURES

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 13

DO NOT USE THE ATTACHED HAND-

HELD HOSE TO SPRAY ANYTHING OTHER

THAN THE INTERIOR OF THE COMBITHERM

OVEN COMPARTMENT.

DO NOT USE THE SPRAY HOSE

ON THE SURFACE OF A HOT COOKING

COMPARTMENT. ALLOW THE OVEN TO

COOL TO A MINIMUM OF 150°F (66°C).

NOTE: USE AUTHORIZED COMBITHERM OVEN CLEANER ONLY.

UNAUTHORIZED CLEANING AGENTS MAY DISCOLOR OR HARM INTERIOR SURFACES OF THE

OVEN. READ AND UNDERSTAND LABEL AND MATERIAL SAFETY DATA SHEET BEFORE USING

THE OVEN CLEANER.

FOR OPERATOR SAFETY

NOTE AND OBSERVE ALL SAFETY PRECAUTIONS LOCATED THROUGHOUT THIS GUIDE.

IMPORTANT SAFETY PRECAUTIONS

NOTE: Automatic steam venting is a standard

safety feature built into all Combitherm

oven models. This feature vents all

steam from the oven compartment

IMMEDIATELY BEFORE COOKING

TIME EXPIRES.

This function is provided in all

programmed and timed production

when operating in any Steam,

Combination, Convection, and Retherm

cooking mode. Automatic steam

venting does not function if the oven

door is opened before time expires or

when the oven has been set to

continuous operation.

HOT STEAM CAUSES BURNS

ROTATE THE DOOR HANDLE TO THE

FIRST OPEN ROTATION POSITION ONLY.

WAIT UNTIL THE STEAM IS VENTED BEFORE

FULLY OPENING THE DOOR.

DO NOT

HANDLE PANS CONTAINING LIQUID

OR SEMILIQUID PRODUCTS POSITIONED

ABOVE THE EYE LEVEL OF THE OPERATOR.

SUCH PRODUCTS CAN SCALD AND CAUSE

SERIOUS INJURY.

METAL PARTS OF THIS EQUIPMENT

BECOME EXTREMELY HOT WHEN IN

OPERATION. TO AVOID BURNS,

ALWAYS USE HAND PROTECTION

WHEN OPERATING THIS APPLIANCE.

AT NO TIME SHOULD THE INTERIOR OR

EXTERIOR BE STEAM CLEANED, HOSED

DOWN, OR FLOODED WITH WATER OR

LIQUID SOLUTION OF ANY KIND. DO NOT

USE WATER JET TO CLEAN.

SEVERE DAMAGE OR

ELECTRICAL HAZARD COULD RESULT.

WARRANTY BECOMES VOID IF APPLIANCE IS FLOODED.

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 14

The Steam mode provides the operator with the ability to steam, poach, or blanch.

This mode will automatically steam at the boiling point of water; quick-steam above the

boiling point for faster cooking results; or low temperature steam, below the boiling point,

for more delicate products such as pâté, mousse, seafood, or custard.

PRESS THE ON/OFF POWER KEY TO THE ON POSITION.

PRESS THE STEAM MODE KEY.

Automatic Steam temperature of 212°F (100°C) will appear in the display.

The last set time or oven control default setting for time will appear in the display.

PRESS THE START KEY TO STEAM AT THE SETTINGS SHOWN.

TO CHANGE THE SETTINGS SHOWN:

PRESS THE TEMPERATURE KEY.

The cooking temperature will appear highlighted within the oven display.

Press the up  and down  arrow keys or rotate the adjustment knob to select

the desired cooking temperature.

• Automatic Steaming 212°F (100°C)

• Quick-steaming 213°F to 248°F (101°C to 120°C)

• Low Temperature Steaming 86°F to 211°F (30°C to 99°C)

TO COOK BY TIME:

PRESS THE TIME KEY.

The cooking time will appear highlighted within the oven display.

Press the up  and down  arrow keys or rotate the adjustment knob to

select the time desired…

or

Set control for continuous operation by rotating the adjustment knob to the right until

appears in the display.

TO COOK BY INTERNAL PRODUCT TEMPERATURE:

PRESS THE CORE TEMP KEY.

The previously set core temperature or oven control default setting will appear

highlighted within the oven display.

Press the up  and down  arrow keys or rotate the adjustment knob to

select the internal temperature desired and insert the product probe.

PRESS THE START KEY TO BEGIN COOKING IN THE STEAM MODE.

• The set cooking temperature will appear in the display. To adjust the set temperature, press the key

once and make corrections as required. To display the actual oven temperature, press the key twice.

• The remaining cooking time will appear in the display. To display the set time or to change the set

values for time during operation, press the time key once and make corrections as required.

• The actual internal product temperature will appear in the display. To display the set internal product

temperature or to change the set values for core temperature during operation, press the key once

and make corrections as required.

When the cooking time has expired or the operator set internal temperature has been reached, a buzzer

will sound indicating the end of the operating mode.

• To stop the buzzer, press the start/stop key or open the oven door.

STEAM MODE

STEAM ● LOW TEMPERATURE STEAM ● QUICK STEAM

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 15

This mode will steam a full or partial load of a single product, or multiple products

without transfer of flavors. When steaming multiple products, however, individual

product cooking times must be taken into consideration. The non-pressurized

atmosphere of the Combitherm also provides the ability to open the door during the

steam mode in order to monitor products more closely throughout the steaming process.

STEAM

Perforated, 2-1/2" deep pans

(65mm) are particularly suitable

for use in this program mode.

These pans will provide a shorter

cooking time and will prevent

product over-cooking at the

bottom of the pan.

Separate ice-encased vegetables

before steaming to assure more

even cooking.

A variety of products can be

steamed at the same time but

attention must be paid to the

different cooking times required

for each food product.

Butter and season vegetables

after steaming.

Steam long-grain rice using

approximately 1-part rice to

approximately 1-1/2-parts water

or seasoned liquid.

Steam durum wheat noodles in

unperforated pans using 1-part

noodles to 5-parts cold water.

QUICK STEAMING

Quick steaming is suitable

for hearty, root-type vegetables

such as potatoes, legumes,

and cabbage.

Quick steaming provides a

cooking time which is

approximately 10-percent shorter

than the regular steam mode

temperature of 212°F (100°C).

Set the steam cooking

temperature between 221°F

(105°C) and 230°F (110°C) for

small loads and between 230°F

(110°C) and 248°F (120°C) for

full loads.

LOW TEMP STEAM

The low temperature steam mode

will function whenever the oven

compartment temperature is

below 212°F (100°C).

Proof yeast dough at a

temperature setting of 90°F to

110°F (32°C to 43°C).

It will take longer to steam

products using the low

temperature steam mode.

Steaming sausages in low

temperature steam prevents

cracked or peeling skins.

Use low temperature steam for

delicate foods such as shrimp,

fish, seafood, and crème caramel.

For best results, low temperature

steam all delicate food items at a

temperature of 210°F (99°C)

or below.

STEAM MODE

CHEF OPERATING TIPS

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 16

The Combination mode will prove to be the most versatile and widely used mode

the Combitherm oven has to offer. It will produce the best possible results on the

widest variety of products — all within the shortest period of time. The unique control

function of this mode enables the operator to roast or bake with a combination of

steam and convection heat. In addition to shorter cooking times, this combination of

steam and heat offers less product shrinkage and more moisture retention than obtained

in a standard convection oven.

PRESS THE ON/OFF POWER KEY TO THE ON POSITION.

PRESS THE COMBINATION MODE KEY.

The last set values or oven control default setting for temperature will appear in the display.

The last set time or oven control default setting for time will appear in the display.

PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.

TO CHANGE THE SETTINGS SHOWN:

PRESS THE TEMPERATURE KEY.

The cooking temperature will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob to

select the desired cooking temperature.

• 212°F to 482°F (100°C to 250°C)

TO COOK BY TIME:

PRESS THE TIME KEY.

The cooking time will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob to select

the time desired…

or

Set control for continuous operation by rotating the adjustment knob to the right until

appears in the display.

TO COOK BY INTERNAL PRODUCT TEMPERATURE:

PRESS THE CORE TEMP KEY.

The core temperature will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob to

select the internal temperature desired and insert the product probe.

PRESS THE START KEY TO BEGIN COOKING IN THE COMBINATION MODE.

• The set cooking temperature will appear in the display. To adjust the set temperature, press the key

once and make corrections as required. To display the actual oven temperature, press the key twice.

• The remaining cooking time will appear in the display. To display the set time or to change the set

values for time during operation, press the time key once and make corrections as required.

• The actual internal product temperature will appear in the display. To display the set internal

product temperature or to change the set values for core temperature during operation, press the

key once and make corrections as required.

When the cooking time has expired or the operator set internal temperature has been reached, a

buzzer will sound indicating the end of the operating mode.

• To stop the buzzer, press the start/stop key or open the oven door.

COMBINATION MODE

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 17

Due to the automatic steam adjustment, the

door can be opened at any time during a

cooking operation. Be certain to observe the

safety warning when opening the oven door.

The Combination mode is particularly efficient

when used for baking, broiling, grilling, stewing,

braising, and roasting.

When using the Combination mode, cooking

temperatures can be reduced 10- to 20-percent

below the temperatures used for conventional

cooking methods.

Cooking time will be reduced approximately

40-percent when cooking at the same temperature

used for convection oven cooking and up to 50- to

60-percent less time when cooking at the same

temperature used for a conventional oven.

Food browning in the Combitherm begins

at a cooking temperature of approximately

248°F (120°C).

A higher cooking temperature results in heavier

browning but also results in greater product

weight loss. To achieve additional browning use

the Moisture Vent Key or set Gold-n-Brown into

the product procedure. Gold-n-Brown is

particularly useful for adding color to high moisture

products such as chicken and other poultry items

or for additional browning of full loads and other

moist products.

The Combination mode provides even browning

without the necessity to turn the pans.

For more even cooking, do not cook in pans

deeper than 4-inches (100mm).

The Combination mode injects the optimum amount of steam

automatically. There is no need to select moisture levels. Foods do not

dry out. Flavors are retained with no transfer of flavors when mixing

product loads.

COMBINATION MODE

CHEF OPERATING TIPS

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 18

The Convection mode operates with hot circulated air within a temperature range

of 86° to 482°F (30° to 250°C). For many applications, better results may be

achieved with the Combination mode; therefore, the operator may want to consider

using the Convection mode on a more limited basis.

PRESS THE ON/OFF POWER KEY TO THE ON POSITION.

PRESS THE CONVECTION MODE KEY.

The last set values or oven control default setting for temperature will appear in the display.

The last set time or oven control default setting for time will appear in the display.

PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.

TO CHANGE THE SETTINGS SHOWN:

PRESS THE TEMPERATURE KEY.

The cooking temperature will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob

to select the desired cooking temperature.

• 86° to 482°F (30° to 250°C)

TO COOK BY TIME:

PRESS THE TIME KEY.

The cooking time will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob to select the

time desired…

or

Set control for continuous operation by rotating the adjustment knob to the right until

appears in the display.

TO COOK BY INTERNAL PRODUCT TEMPERATURE:

PRESS THE CORE TEMP KEY.

The core temperature will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob to

select the internal temperature desired and insert the product probe.

PRESS THE START KEY TO BEGIN THE COOKING MODE.

• The set cooking temperature will appear in the display. To adjust the set temperature, press the key

once and make corrections as required. To display the actual oven temperature, press the key twice.

• The remaining cooking time will appear in the display. To display the set time or to change the set

values for time during operation, press the time key once and make corrections as required.

• The actual internal product temperature will appear in the display. To display the set internal product

temperature or to change the set values for core temperature during operation, press the key once

and make corrections as required.

When the cooking time has expired or the operator set internal temperature has been reached, a buzzer

will sound indicating the end of the operating mode.

• To stop the buzzer, press the start/stop key or open the oven door.

To check the length of time the product has been operating in the core temperature mode, press and hold the

time key along with the core temperature key . The time period will appear at the top of the display.

CONVECTION MODE

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 19

The Convection mode works best with foods

containing little moisture or for very moist food

which require a dryer finished product.

For baking, preheat the Combitherm at a

temperature of 36°F to 54°F (20°C to 30°C) above

the baking temperature required. Once preheated,

reset the temperature as required.

A higher cooking temperature results in heavier

browning but also results in greater product weight

loss. To achieve additional browning use the

Moisture Vent Key or set the Browning Feature

into the product procedure.

To prevent the surface of food from excessive

drying, the fan will not engage if the internal

oven temperature is above 212°F (100°C)

and the set oven temperature is below

212°F (100°C).

The Convection Mode can be used to roast or bake products needing very

short cooking times or for high moisture products such as muffins, cakes,

and cookies, or for browning the surface of the product.

CONVECTION MODE

CHEF OPERATING TIPS

S ECTION 1 – CONTROL PANEL I DENTIFICATION • COMBITHERM GAS TECHNICAL S ERVICE M ANUAL • 20

The Retherm mode can be used to rethermalize (regenerate) portioned food on

plates, trays, or platters within a short period of time. Steam is automatically injected

into the oven compartment as required. Items are brought up to proper serving

temperatures without dry edges or condensate forming on the plates.

PRESS THE ON/OFF POWER KEY TO THE ON POSITION.

PRESS THE RETHERM MODE KEY.

The last set values or the default settings will appear in the display.

PRESS THE START KEY TO COOK AT THE SETTINGS SHOWN.

TO CHANGE THE SETTINGS SHOWN:

PRESS THE TEMPERATURE KEY.

The cooking temperature will appear highlighted within the oven display.

Press the up

 and down  arrow keys or rotate the adjustment knob

to select the desired cooking temperature.

• 248° to 320°F (120° to 180°C)

TO COOK BY TIME:

PRESS THE TIME KEY.

The cooking time will appear highlighted within the oven display.

Press the up  and down  arrow keys or rotate the adjustment knob to select the

time desired…

or

Set control for continuous operation by rotating the adjustment knob to the

right until appears in the display.

TO COOK BY INTERNAL PRODUCT TEMPERATURE:

PRESS THE CORE TEMP KEY.

The core temperature will appear highlighted within the oven display.

Press the up  and down  arrow keys or rotate the adjustment knob to

select the internal temperature desired and insert the product probe.

PRESS THE START KEY TO BEGIN THE RETHERM MODE.

• The set cooking temperature will appear in the display. To adjust the set temperature, press the key

once and make corrections as required. To display the actual oven temperature, press the key twice.

• The remaining cooking time will appear in the display. To display the set time or to change the set

values for time during operation, press the time key once and make corrections as required.

• The actual internal product temperature will appear in the display. To display the set internal product

temperature or to change the set values for core temperature during operation, press the key once

and make corrections as required.

When the cooking time has expired or the operator set internal temperature has been reached, a buzzer

will sound indicating the end of the operating mode.

• To stop the buzzer, press the start/stop key or open the oven door.

To check the length of time the product has been operating in the core temperature mode, press and hold the

time key along with the core temperature key . The time period will appear at the top of the display.

RETHERM MODE

Page is loading ...

Alto-Shaam COMBITOUCH SERIES 6•10ESG Technical & Service Manual

This manual is also suitable for

Alto-Shaam COMBITOUCH SERIES 6•10ESG Technical & Service Manual

Related papers

Other documents