BlueTrek COMPACT CLASSIC Owner's manual
- Category
- Mobile phones
- Type
- Owner's manual
English
1 I BLUETREK COMPACT CLASSIC
Before using your BLUETREK® COMPACT CLASSIC for the first time, you must charge it
continuously for approximately 3 hours, until the indicator change to green.
Please refer to the “Charging the BLUETREK® COMPACT CLASSIC” section of this manual.
Introduction
The BLUETREK® COMPACT CLASSIC is a wireless car kit based on Bluetooth® technology.
It complies with Bluetooth® 2.0 protocol, supporting Headset and Handsfree profile.
The BLUETREK® COMPACT CLASSIC has 3 buttons:
“TALK” button (main button)
“VOL+” button
“VOL-“ button
Powerful speaker
Rotary microphone
arm
VOL- button
VOL+ button
Indicator light
Charging Socket
TALK button
English
BLUETREK COMPACT CLASSIC I 2
Using the BLUETREK® COMPACT CLASSIC in dierent
environment
Mounting on the sun visor as a car kit
When using your BLUETREK® COMPACT CLASSIC in your car, simply mount the unit onto
the visor with the clip as shown in Diagram 1.
Mic 1
Mic 2
Diagram 1
For best voice reception, please adjust the rotary microphone arm around 45 degree, or
other position suits you most.
English
3 I BLUETREK COMPACT CLASSIC
Charging the BLUETREK® COMPACT CLASSIC
Connect the charging cable to the car charger and insert the car charger into the cigarette
lighter socket as shown in Diagram 2.
Diagram 2
English
BLUETREK COMPACT CLASSIC I 4
You can also connect the charging cable to a USB socket.
Diagram 3
While charging, the indicator light on the BLUETREK® COMPACT CLASSIC should be orange.
The green indicator light will turn on when the unit is fully charged. Subsequent charges
should take approximately 3 hours.
When the indicator light on your BLUETREK® COMPACT CLASSIC ashes in red at regular
intervals (or the voice alert is activated), the unit needs to be recharged.
English
5 I BLUETREK COMPACT CLASSIC
Pairing the BLUETREK® COMPACT CLASSIC
Before using the BLUETREK® COMPACT CLASSIC, you must pair it with your Bluetooth®
mobile phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can
communicate.
To initiate pairing:
1. Place the BLUETREK® COMPACT CLASSIC and your mobile phone within 0.3 meter (1
foot) from each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the Bluetooth®
mobile phone user manual).
3. When the BLUETREK® COMPACT CLASSIC is switched on, press and hold both the TALK
button and the VOL+ button for about 5 seconds until the indicator light ashes red and
blue alternately. And a sound can be heard in the speaker.
4. Once the mobile phone detects the car kit, a “BLUETREK COMPACT CLASSIC” message
will be displayed. Follow the phone instructions to accept the pairing. The PIN code (or
passkey) is 0000, then press “yes” or “ok”.
If pairing was successful, the indicator light will switch to blue.
If you haven’t started the discovery mode within 5 minutes, it will stop. In this case, you
must start the pairing again as step 3 above.
English
BLUETREK COMPACT CLASSIC I 6
Switching the BLUETREK® COMPACT CLASSIC ON and OFF
Switching the BLUETREK® COMPACT CLASSIC ON
Switch on the BLUETREK® COMPACT CLASSIC by lifting up
the microphone arm as shown in Diagram 4. You will hear
a beep (2 tones) in the speaker (and continuous
connecting beeps until it is connected to the handset).
During about 5 seconds, you can see the blue LED blinking
until the BLUETREK® COMPACT CLASSIC is switched on.
Once the BLUETREK® COMPACT CLASSIC is switched on,
you can see the blue LED keeps lighting.
Switch o the BLUETREK® COMPACT CLASSIC as shown
in Diagram 5.
Switching the BLUETREK® COMPACT CLASSIC OFF
Diagram 4
Diagram 5
English
7 I BLUETREK COMPACT CLASSIC
Making a call
Make sure the headset is paired to your phone and in range, dial the number on the phone
keypad and press call.
*For mobile phone with voice recognition
· Make sure the voice recognition function on your mobile is activated and your voice tags
have been recorded with the phone. To enter these, please refer to your phone’s manual.
· When there is no incoming or active call, press once on the TALK button
· Wait for the audio signal sent by the mobile phone (generally a short tone).
· Speak the name of person you wish to call.
*This function may not be available on some phones, please refer to your phone’s manual.
Answering a call
When your BLUETREK® COMPACT CLASSIC is OFF
Switch on your BLUETREK® COMPACT CLASSIC. After about 3 seconds, It will automatically
transfer the call from the phone to the car kit For some phones, you may need to press
“Connect” on the phone.
When your BLUETREK® COMPACT CLASSIC is ON
Press once on the TALK button to take the call.
English
BLUETREK COMPACT CLASSICT I 8
Ending a call
Press once on the TALK button to end an active call.
Adjusting the volume
To increase the volume during an active call, press the “VOL+” button on the BLUETREK®
COMPACT CLASSIC.
To decrease the volume during an active call, press the “VOL-“ button on the BLUETREK®
COMPACT CLASSIC.
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ or VOL- button for approximately 2 seconds. A
periodic tone can be heard in the speaker when the microphone is muted. You can still adjust
the speaker volume by pressing shortly on the VOL+ or Vol- button.
To end the mute function
When the microphone is muted, press and hold the VOL+ or VOL- button for approximately 2
seconds. The periodic tone will end.
English
9 I BLUETREK COMPACT CLASSIC
Transferring a call from the BLUETREK® COMPACT CLASSIC
to the mobile phone
With a phone in Headset Profile
During an active call, to transfer it to the phone, simply turn o your BLUETREK® COMPACT
CLASSIC.
With a phone in Hands-Free Profile
During an active call, to transfer it to the phone, double click on the TALK button.
Transferring a call from the mobile phone to your
BLUETREK® COMPACT CLASSIC
With a phone in Headset Profile
Switch on your BLUETREK® COMPACT CLASSIC.
With a phone in Hands-Free Profile
During an active call on the mobile phone, double click on the TALK button. It will take few
seconds to re-establish the connection between the mobile phone and the car kit. (Some
phones may need fulfil this function by pressing once to reconnect the mobile phone to the
BLUETREK® COMPACT CLASSIC.)
English
BLUETREK COMPACT CLASSIC I 10
Call waiting
When you hear a call waiting alert while you are on a call, press the TALK button on the
BLUETREK® COMPACT CLASSIC approximately 2 seconds to accept the second call and
place the current call on hold.
To switch between an active call and a held call, press the TALK button on the BLUETREK®
COMPACT CLASSIC approximately 2 seconds.
To end the active call and take the held call, press the TALK button once on the BLUETREK®
COMPACT CLASSIC.
Rejecting a call
Press the TALK button on your car kit for approx. 3 seconds to reject the call.
Redial the last number
With a phone in Headset Profile
This function is not available.
With a phone in Hands-Free Profile
When there is no incoming or active call, press the TALK button on your carkit for approx. 2
seconds.
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
BlueTrek COMPACT CLASSIC Owner's manual
- Category
- Mobile phones
- Type
- Owner's manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
Other documents
-
Hama 00104803 Owner's manual
-
-
-
-
-
-
-
-
Conceptronic CBTCARKIT Datasheet
-