Chicago Electric 92708 User manual

Brand: Chicago Electric

Model: 92708

Category: Power adapters & inverters

Type: User manual

POWER INVERTER

400 WATT / 800 WATT PEAK

ASSEMBLY AND OPERATING INSTRUCTIONS

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at http://www.harborfreight.com

2005 by Harbor Freight Tools

of this manual or any artwork contained herein may be reproduced in any shape or

form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353

TO PREVENT SERIOUS INJURY,

READ AND UNDERSTAND ALL WARNINGS

AND INSTRUCTIONS BEFORE USE.

92708

SKU 92708 Page 2For technical questions, please call 1-800-444-3353.

Save This Manual

You will need the manual for the safety warnings and precautions, assem-

bly instructions, operating and maintenance procedures, parts list and diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the

front cover. Keep the manual and invoice in a safe and dry place for future refer-

ence.

Safety Warnings and Precautions

WARNING: When using this device, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Do not plug a battery charger into the inverter if the charger has a warning

that dangerous voltages are present at the battery terminals.

2. Keep work area clean. Cluttered areas invite injuries.

3. Keep inverter away from any direct heat source or combustible material.

4. Observe work area conditions. Do not use machines or powered products

in damp or wet locations. Don’t expose to rain. Keep work area well lit. Do not

METINOITPIRCSED

rewoPsuounitnoCsttaW004

rewoPkaePsttaW008

egatloVtupnI)elbissopstloV51-11(CDlanimoNstloV21

atloVtuptuOzH06taCAstloV021

selcatpeceRCAsteltuOdeziraloP,gnorP-3owT)2(

esuFspmA04

snoisnemiD-2xW"8/3-7xW"8/

1-5

thgieWsbl8.2

srotacidnInorewop=DELneerG

hctiwSffO/nO,epytrekcoR

erutarepmeTgnitarepOF°311-41

selbaCyrettaB)y

letamixorppa('2,GWA9

serutaeF

noitcetorpdaolrevohtiwevawenisdeifidoM-

mralaegatlovwoL-

nwodtuhsdna

;V11ta

V01tuobata

Specifications

REV 04/05

SKU 92708 Page 3For technical questions, please call 1-800-444-3353.

use electrically powered products in the presence of flammable gases or liq-

uids.

5. Keep children away. Children must never be allowed in the work area. Do

not let them handle machines, equipment, or extension cords.

6. Store idle equipment. When not in use, this product must be stored in a dry

location to inhibit rust.

7. Use the right inverter for the job. Do not attempt to force a small inverter or

attachment to do the work of a larger industrial inverter. There are certain

applications for which this inverter was designed. It will do the job better and

more safely at the rate for which it was intended. Do not modify this inverter

and do not use this inverter for a purpose for which it was not intended.

8. Dress properly. Do not wear loose clothing or jewelry as they can be caught

in moving parts. Protective, electrically nonconductive clothes and nonskid

footwear are recommended when working. Wear restrictive hair covering to

contain long hair.

9. Use eye protection. Always wear ANSI approved impact safety goggles when

using inverters.

10. Do not overreach. Keep proper footing and balance at all times. Do not reach

over or across running machines.

11. Maintain inverters with care. Keep inverters clean for better and safer per-

formance. Follow instructions for changing accessories. Inspect inverter cords

periodically and, if damaged, have them repaired by an authorized technician.

12. Disconnect power. Unplug inverter when not in use.

13. Avoid unintentional starting. Be sure the switch is in the Off position when

not in use and before plugging in any appliance.

14. Stay alert. Watch what you are doing, use common sense. Do not operate

any inverter when you are tired.

15. Check for damaged parts. Before using any inverter, any part that appears

damaged should be carefully checked to determine that it will operate properly

and perform its intended function. Check for alignment and binding of moving

parts; any broken parts or mounting fixtures; and any other condition that may

affect proper operation. Any part that is damaged should be properly repaired

or replaced by a qualified technician. Do not use the inverter if any switch does

not turn On and Off properly.

16. Servicing. This device should be serviced only by a qualified technician. Aside

from the fuse, this item does not have any user-replaceable parts.

SKU 92708 Page 4For technical questions, please call 1-800-444-3353.

17. Do not operate inverter if under the influence of alcohol or drugs. Read

warning labels on prescriptions to determine if your judgment or reflexes are

impaired while taking drugs. If there is any doubt, do not operate the inverter.

18. Guard against electric shock.

Do not open the metal case; risk of electric shock.

Prevent body contact with grounded surfaces such as pipes, ra-

diators, ranges, and refrigerator enclosures during installation.

Connect all wires securely and cover the connections with insulat-

ing rubber boots (not included).

Store inverters and metal objects away from the inverter.

19. People with pacemakers should consult their physician(s) before using

this product. Electromagnetic fields in close proximity to a heart pacemaker

could cause interference to or failure of the pacemaker.

20. Keep the Inverter well-ventilated. Do not place any objects on top of or next

to the Inverter or allow anything to cover the cooling fans; doing so can cause

the Inverter to overheat, causing a potential fire hazard and/or damage to the

Inverter. Leave adequate ventilation space underneath the Inverter as well;

thick carpets or rugs can obstruct air flow, causing the Inverter to overheat.

21. Read and adhere to all warnings and safety precautions in the owner’s

manual for the device that this inverter is used to power.

22. A vehicle’s engine must never be used in any sealed structure. Carbon

monoxide is produced during operation and is DEADLY in a closed envi-

ronment. Early signs of carbon monoxide poisoning resemble the flu, with

headaches, dizziness, or nausea. If you have any of these signs, get fresh air

immediately.

Note: Performance of this unit may vary depending on the available battery power

or appliance wattage.

Warning: The warnings, cautions, and instructions discussed in this instruc-

tion manual cannot cover all possible conditions and situations that may occur.

It must be understood by the operator that common sense and caution are

factors which cannot be built into this product, but must be supplied by the

operator.

Unpacking

When unpacking, check to make sure that the Inverter is in good condition.

If any parts are missing or broken, please call Harbor Freight Tools at the number

on the cover of this manual as soon as possible.

SKU 92708 Page 5For technical questions, please call 1-800-444-3353.

Connection

For the power inverter to work properly, your power source must provide 12 volts

DC, and the power source must provide enough current (i.e., 32 amps to operate

the load of 384 Watts or under).

Caution: This inverter must only be connected to batteries with a nominal

output voltage of 12 volts. Lower voltage will not operate the inverter prop-

erly, and more voltage could damage the inverter or the device being pow-

ered. If more than one 12 volt battery is to be used, the batteries must be

connected in a parallel circuit; batteries connected in a series circuit will pro-

duce too much voltage.

1. Place the Power Inverter on a flat surface. Make sure it has adequate ventilation

and is not in direct sunlight. Fasten the inverter securely to the surface, using

screws or some other means. If holes are to be drilled, follow safe, proper

installation techniques.

2. Connect the Battery Cable lugs to the (Positive) red and (Negative) black

terminals on the back of the Inverter. Securely tighten.

3. The Power Inverter can be used either while the engine is running or off.

Connect the Battery Cables to the Negative (black) and Positive (red) terminals

of the battery.

BACK

WARNING!

Risk of Fire!

The positive battery

terminal connection

must be the LAST

connection and must

be done with the

inverter’s switch off.

Negative

Positive

REV 06/06

SKU 92708 Page 6For technical questions, please call 1-800-444-3353.

Maintenance

1. Keep this unit clean and dry. Unplug the unit before cleaning. Clean only the

outside of this unit with a soft, dry cloth; never clean this unit with water or

harsh cleaners.

2. Aside from the fuse, this device does not contain any user replaceable parts. If

it needs service, take it to a qualified technician.

3. If the fuse needs replacement, simply disconnect the inverter, remove the fuse

cover on the back panel (see

Back

, page 5), remove the old fuse, and replace

it with another 40 Amp fuse of the same type. Replace the fuse cover and

reconnect the inverter before use.

Operation

1. Plug the 115 VAC device(s) you wish to power into the 3-prong AC Receptacles.

See

FRONT

above. The appliance(s) must not use more than 400 (total) watts

during continuous operation, otherwise it may overload the Inverter.

Caution: Some rechargeable appliances may damage the Power Inverter or

the appliance. When first using a rechargeable device, check the inverter’s

temperature for the first 10 minutes. If it becomes abnormally hot, do not use

this device with the Inverter.

2. Flip the Power Switch to the On (I) position to turn on. Do not use the appliance

until the green power LED indicator is on.

3. Turn on appliance. If an alarm sound is heard, turn off the appliance.

Caution: It is recommended that the vehicle be started every hour to recharge

the battery. Doing this will help prevent any unexpected shutdown of the

equipment. This will also help ensure that there will be enough battery power

to start the vehicle. Due to the risk of carbon monoxide inhalation (see

Warn-

ing

# 23 on page 4), do not run the vehicle’s engine within an enclosed area.

4. After use, disconnect the appliances, flip the Power Switch to the Off (O) position.

FRONT

Outlets

Power

Indicator

Switch

SKU 92708 Page 7For technical questions, please call 1-800-444-3353.

Troubleshooting Tips

1. If the low battery alarm sounds, this means that the input voltage is below the

necessary 11 V. The battery needs recharging. You should stop using the

appliance and then recharge the battery. If this is not done, the Inverter will

shut off automatically at around 10 V.

2. If you are unsure if the inverter will have the proper amount of current to run

the device, use this rough guideline: Take the power consumption of the load

in watts and divide it by 12 (input voltage). The result will be the approximate

number of amps needed to power your device.

Example: Load is rated at 312 watts. 312 watts / 12 V = 26 amps needed. You

could use this device with the inverter.

3. If your television will not start, it is important to keep in mind that some appliances

(including many televisions) may require two to six times their wattage to start

up.

4. If your audio system buzzes while using this inverter, it is because some sound

systems can not filter out the modified sine wave produced by the inverter.

Use a sound system that incorporates a higher quality power supply.

5. This inverter is made to minimize the interference with TV signals. However,

especially with weak TV signals, some interference may still be visible. To

correct this, place the inverter as far away as possible from the television

antenna and it’s cables. Next, adjust the orientation of the inverter to the antenna

cables and TV power cord to minimize the interference. Also use a shielded

antenna cable.

6. If the low battery alarm is on all the time, try these corrective measures:

Recharge battery if in poor condition. Next, check the battery connection. You

may need to clean the connectors.

7. If you are getting a low output voltage, try reducing the load to minimize watts.

You may have overloaded the inverter. Reduce your load to 390 watts. Also,

keep input voltage above 11 volts to maintain a constant flow of power.

8. If you are not getting any power output, turn the power switch Off and On

again, until the green power light comes on. Your devices may draw too much

power to operate them. The inverter may be in thermal shutdown. Let it cool

down and make sure there is adequate ventilation around the unit.

Chicago Electric 92708 User manual

Brand: Chicago Electric

Model: 92708

Category: Power adapters & inverters

Type: User manual

Download PDF

report

Chicago Electric 92708 User manual

Chicago Electric 92708 User manual

Related papers

Other documents